wear-resisting Suction pipe The manufacturing of is highly automated and the production speed is very fast. The general air duct can produce 20~40 meters per minute. Due to the low price of its raw material galvanized strip steel compared with the whole galvanized steel sheet, and its factory production and specification standardization, the cost of spiral air duct is lower than that of rectangular air duct; In addition, the total cost of spiral air duct is low due to the less demand for supports and hangers and the less installation work. Since the four corners of rectangular air ducts are prone to turbulence, reducing the effective flow area, the spiral air ducts have good air fluidity and large effective flow area, so the secondary noise of spiral air ducts is low. Because the spiral air ducts are strong, the low-frequency noise caused by air duct vibration is smaller, the air flow performance is good, the system pressure drop is small, and the daily operation system consumes less power. Spiral air ducts in the market are generally divided into three categories according to their materials: galvanized spiral air ducts, stainless steel spiral air ducts and composite spiral air ducts. Among them, spiral air duct has the best quality and strong applicability, but its price is high. At present, the most widely circulated spiral air duct on the market is galvanized sheet. The galvanized sheet spiral air duct is basically the characteristic of stainless steel spiral air duct, but its price is only two thirds or even lower than that of spiral air duct. Taiyuan Suction pipe It is generally used in places where the external environment is relatively common and the requirements for air ducts are not too high. As the iron sheet is prone to chemical reaction in various environments, corrosion and rust will occur. However, zinc hardly changes in dry air. In humid air, dense basic zinc carbonate film will be formed on the surface of zinc. The spiral air duct is mainly coated with zinc on the iron sheet of the air duct to protect the iron sheet. The protective and decorative properties of zinc coating can be significantly improved after passivation treatment, dyeing or coating with light protecting agent.

The development trend of HVAC duct is wear-resisting Suction pipe Now more and more companies choose advanced spiral duct technology. The advantages of spiral air duct are as follows: 1. Good air tightness. Spiral air duct greatly reduces the connection of air duct and minimizes the leakage between connectors. The typical spiral air duct is 3-6m, but the typical rectangular air duct is only 1-1.5m; At the same time, only one connector is required to connect two spiral air ducts, while a typical rectangular air duct connector requires separate double flanges. 2. Standardized products. The production of spare parts (pipes and connectors) is highly automated and systematic, and has industrialized quality control. 3. Low installation cost. The installation of round duct only needs one third of that of rectangular duct. 4. Save space. Under the same pressure and the same installation space, the spiral air duct with a diameter of 200mm can replace the rectangular air duct with a diameter of 250x150mm. Without increasing the installation space, multiple spiral pipes can be used instead of wider rectangular pipes. Considering various factors, in most cases, spiral pipes require less space than rectangular pipes. Under the same pressure, the installation space of several spiral pipes is equal to or less than that of rectangular pipes. Most rectangular pipe systems require 4 bolts to fix, which will increase 40~80mm in each direction. 5. The pressure drop is low. As we know, spiral duct has lower ventilation resistance than rectangular duct. 6. Precision locking technology. Taiyuan Suction pipe The mold on the is made of special steel. After years of use, the surface remains unchanged, making the surface of the spiral air duct free of scratches and extending the service life. 7. The perimeter of rectangular air duct with length width ratio of 1:3 at the same section is 40% larger than that of spiral air duct, which means that spiral air duct saves more materials and reduces thermal insulation.

Taiyuan Suction pipe It is a kind of hose that can be used for sand pumping and sand suction produced with high abrasion resistant rubber. It is often used in sand blasting industry, cement, steel, minerals and other industries, but it is mainly used in river dredging, slurry transportation in mines, sand digging and sand taking and other industries to transport sharp granular solids or solid-liquid mixtures. Its product structure is composed of high wear-resistant layer, reinforced water pipe layer, skeleton steel wire and outer rubber. Today, Myers will introduce the application field of wear-resistant sand absorption rubber pipe. When the wear-resistant sand suction rubber pipe is applied in the mine pit, it is necessary to set a floating boat equipped with a sand pump in the mine pit, and use the floating sand suction rubber pipe to connect with the sand pump. The floating boat will float up and down with the rise and fall of the water level. It is required that the pipe body has good flexibility and good tear resistance and bending resistance. The offshore pipeline is connected by non floating sand suction hose until the pulp transportation destination. The overall pipeline is divided into two parts, one for surface use and the other for onshore use. The main raw material of these two kinds of hoses is high abrasion and corrosion resistant rubber, and cord reinforcement layer and steel wire skeleton layer are added in the pipe wall to ensure the pressure resistance and tear resistance of the hose. The connection mode is vulcanized flange connection, that is, the flange and the hose are a whole, so there is no need to worry about the flange falling off. Floating sand suction hose used on the water surface. This kind of hose is required to float on the water surface. Due to the large drop of the mine (100 meters) and the long conveying distance Suction pipe company The hose shall have high pressure resistance, and the design pressure is 25 kg/cm2 according to the calculation. It should be considered that the floating ship will move up and down with the rise and fall of the water level and the wave will cause lateral displacement. Its internal structure is the same as the sand suction hose used offshore, except that a floating body is installed outside the hose.

wear-resisting Suction pipe The inner and outer walls are smooth, the resistance of the air duct is small, the secondary noise is not generated during air supply and exhaust, the energy consumption is reduced, and the operation cost is saved. The product can be made on site, cut, drilled, and opened, the installation is simple, and the labor and time are saved. The user's investment cost is reduced, the construction period is shortened, the performance price ratio is high, and it is cheaper than other materials. After the installation is completed, no maintenance is required, and the maintenance cost is reduced. The key points of whether galvanized sheet air duct material galvanized sheet is corroded are mainly reflected in the following three aspects: ① The first corrosion of galvanized sheet in the entire service life cycle is the oxidation of the galvanized layer on the surface, resulting in white rust. After a little longer time, the white rust on the surface further reacts with carbon dioxide and other impurities in the humid air to form black spots. When the galvanized sheet is used for a long time and the galvanized layer is severely corroded, the steel base loses the sacrificial anti-corrosion effect of zinc, and begins to oxidize to generate red rust. Once the steel base begins to oxidize, the corrosion rate becomes very fast, and the life of galvanized sheet ends. ② In addition, there are two special corrosion conditions of galvanized sheet, namely, black stain. One is that after being used for a period of time, due to the influence of lead and other elements in the zinc coating, the galvanized sheet will become black in the matte part of the zinc flake. The blackened zinc coating still has a protective effect on the steel base, but has a certain impact on the service life. ③ Suction pipe company It has excellent corrosion resistance in dry or pollution-free environment. However, in the polluted environment, the service life will be greatly shortened, so it is necessary to pre coat the film into color plates before use.

wear-resisting Suction pipe The thickness of the seaming plate shall be within the regular range of products of various specifications. If it is less than the thickness, cracks, wrinkles and other defects are likely to occur during seaming; If it is larger than the large thickness, as the square of the plate thickness is proportional, the bending force will significantly increase, which will cause abnormal damage to the forming roller, overloading of the transmission system, and stuffiness. In dust removal system: galvanized air duct can be used for collection and transportation of dust removal device. In the oil smoke exhaust system: there are a lot of oil smoke in restaurants, restaurants and hotel kitchens, which need to be discharged. The galvanized air duct is suitable, strong, economical and practical. In air conditioning system: galvanized air duct can be pasted with thermal insulation materials inside, and the surface is beautiful. In bulk material transportation: pneumatic transportation system, some finer and looser material particles can be transported by galvanized air ducts, with low cost and good effect. In the ventilation system: supply fresh air and exhaust gas, exhaust harmful gas outdoors, and send outdoor fresh air indoors. The strength of stainless steel plate shall be higher than that of ordinary steel plate. Before seaming with stainless steel plate, forming test shall be carried out first to avoid overloading the equipment and causing excessive wear or mechanical trouble. Due to the poor plasticity of the aluminum plate, it is easy to crack during the forming of the seaming. The forming test should also be carried out before construction. At the same time, because the aluminum plate is lack of elasticity, the aluminum plate air duct cannot be subject to snap seaming. After the zinc coating of galvanized air duct is passivated, dyed or coated with light protection agent, Suction pipe company It can obviously improve its protection and decoration. The fireproof function of galvanized air duct is mainly reflected in that it is incombustible, but one thing needs to be noted is that whether its insulation layer is burned depends on the material. We suggest that the galvanized air duct should be made of incombustible insulation materials such as centrifugal glass wool.