Nanjing Suction pipe 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Suction pipe Price When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.

Nanjing Suction pipe With the continuous updating of technology, the products are also developing in the continuous updating. At present, the inspection requirements of rubber hose are also improved compared with the previous ones. The inspection index of ultra-high pressure hose shall meet the following index requirements according to the requirements of the Safety Code for High Pressure Water Jet Cleaning Operation: 1) The bursting pressure shall be more than 2.5 times of the working pressure. 2) The test pressure shall be 1.5 times of the working pressure, and the pressure shall be kept for more than 2 minutes without damage. 3) Pulse pressure shall be within the range from zero to working pressure, and 50000 pressure pulses shall be free of damage; The pulse frequency is 15 times/min when the working pressure is 1000-2800bar, and 110 times/min when the pressure is above 2800bar. Since high-pressure cleaning machine has been widely used in all walks of life, and the working condition of high-pressure hose is relatively the worst, we must pay attention to the quality when selecting high-pressure hose, so as to avoid unnecessary safety accidents. Suction pipe Price The development of rubber hose can not be separated from cooperation, R&D and innovation can not be separated from communication, and the inspection requirements of rubber hose have been improved compared with the previous ones. The storage site shall be free of ozone, heat source and equipment generating electromagnetic field. The coiled hoses or hose assemblies shall be stored horizontally, and the stacking height shall be limited to the extent that the products at the bottom will not produce permanent deformation.

Common for ventilation duct high quality Suction pipe What should be paid attention to during processing: the galvanized air duct shall not be connected with s-shaped, c-shaped right angle and vertical angle plugs. Clasp type air duct shall not be used for Grade 1 to 5 clean air. The rivet spacing of air duct shall be less than 100 mm. When the air purification level is 1-5, the rivet spacing of air duct shall be less than 65 mm. Before processing the galvanized air duct, use cleaning solution to remove the oil stain and dust on the surface of the plate. The cleaning solution shall be a neutral detergent, which will not damage the board surface, and will not produce dust after drying, so it will not be harmful to human health. Clean the vent pipe with cleaning solution after fabrication. After cleaning, the electric board shall be sealed in time after the white silk cloth cleaning inspection meets the requirements. The inner wall of color coated steel pipe shall be smooth, and the coating shall not be damaged during steel plate processing. The damaged parts shall be coated with epoxy resin. The galvanized air duct seamed joints, riveted joints and flange flanged corner joints shall be sealed with sealant or other sealing measures according to the design and cleaning level requirements. The sealing materials shall be isobutyl rubber, chloroprene rubber, modified silica gel, etc. The sealing surface of the air duct plate joint shall be located at the positive pressure side of the air duct wall. The production site of galvanized air duct shall be relatively closed, and the production site shall be paved with soft materials that are not easy to produce dust. The galvanized air duct shall have fewer longitudinal joints, glass fiber reinforced plastic ventilation pipes, and no transverse joints. Suction pipe Price The processing of connecting bolts, nuts, washers and rivets shall be galvanized or other anti-corrosion measures, and blind rivets shall not be used.

The hard core method adopts the core extrusion process to extrude the inner rubber tube blank, which directly uses the extruder to cover the inner rubber tube blank on the iron core, instead of the traditional casing process, and simplifies the process flow. Nanjing Suction pipe The billet forming adopts the process method of intertwining outer film and steel wire braiding forming. Similar to wrapping water wrapped cloth, the overlapping width is 1/2 of the film width. This process method can replace the method of wrapping outer film by extruder or by hand, reducing energy consumption and cost. We all know that the reinforcing layer and reinforcing layer of the rubber hose are the main force bearing parts, which are used to bear the load pressure. The factors determining the stress condition of the reinforced layer of the rubber hose are determined by the tension of the braided steel wire and the braiding angle. The high-speed steel wire hose braiding machine developed by our factory has introduced the advanced technology of foreign braiding production lines, and integrated the characteristics of domestic braiding machines. It integrates the advanced functions of hydraulic brake hose braiding production line, such as horizontal mechanical transmission, automatic lubrication, and so on, to develop equipment with high productivity and high degree of automation. The range of braiding diameter can be achieved Ф 6— Ф 25 Long core rubber hose (reinforcement layer). It fills the gap of domestic knitting production equipment, which can be widely used in rubber and plastic hose, rubber hose (reinforcement layer) knitting production equipment. The structure of high-pressure rubber hose is composed of four parts: inner liner, inner rubber layer, skeleton layer, middle rubber layer and outer rubber layer. Suction pipe Price In case of direct contact with the conveying medium, the synthetic rubber with good medium resistance, high tensile strength, high constant tensile stress, small compression permanent deformation and easy processing is usually selected. In order to meet the use requirements of strong polar medium resistance, the inner liner is composed of polytetrafluoroethylene layer and rubber layer, and a layer of film or adhesive is added on the surface of the inner liner to improve the adhesion with the skeleton material.