Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Huzhou Braided hose It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Braided hose Where can I find it? The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.

The development trend of HVAC duct is production Braided hose Now more and more companies choose advanced spiral duct technology. The advantages of spiral air duct are as follows: 1. Good air tightness. Spiral air duct greatly reduces the connection of air duct and minimizes the leakage between connectors. The typical spiral air duct is 3-6m, but the typical rectangular air duct is only 1-1.5m; At the same time, only one connector is required to connect two spiral air ducts, while a typical rectangular air duct connector requires separate double flanges. 2. Standardized products. The production of spare parts (pipes and connectors) is highly automated and systematic, and has industrialized quality control. 3. Low installation cost. The installation of round duct only needs one third of that of rectangular duct. 4. Save space. Under the same pressure and the same installation space, the spiral air duct with a diameter of 200mm can replace the rectangular air duct with a diameter of 250x150mm. Without increasing the installation space, multiple spiral pipes can be used instead of wider rectangular pipes. Considering various factors, in most cases, spiral pipes require less space than rectangular pipes. Under the same pressure, the installation space of several spiral pipes is equal to or less than that of rectangular pipes. Most rectangular pipe systems require 4 bolts to fix, which will increase 40~80mm in each direction. 5. The pressure drop is low. As we know, spiral duct has lower ventilation resistance than rectangular duct. 6. Precision locking technology. Huzhou Braided hose The mold on the is made of special steel. After years of use, the surface remains unchanged, making the surface of the spiral air duct free of scratches and extending the service life. 7. The perimeter of rectangular air duct with length width ratio of 1:3 at the same section is 40% larger than that of spiral air duct, which means that spiral air duct saves more materials and reduces thermal insulation.

Braided hose Where can I find it? Precautions ① The acid and alkali resistant rubber hose used shall not only be oil resistant, but also be pressure resistant, heat resistant, cold resistant, wear resistant and aging resistant. ② The rubber hose should not be too long or too short, generally 1.4 meters. ③ The interface is tight and can be fastened with thin iron wire or clip to prevent falling off and air leakage. ④ It is forbidden to pull acid and alkali resistant rubber hose from one room to another or through walls, floors and floors to prevent accidents caused by rubber hose breaking and falling off. ⑤) The acid and alkali resistant rubber hose should be placed in a place where it can be seen frequently, so that it is easy to detect leakage. Check whether the rubber hose leaks after each bottle change. ⑥ Do not replace acid and alkali resistant rubber hose with universal rubber hose. Since the full rubber hose does not contain a skeleton layer, it is only necessary to use a press out machine to press out the hose; The cloth clamping hose needs to use a molding machine that wraps the adhesive tape on the inner adhesive layer; When forming the suction hose, first wrap the metal spiral wire and then wrap the inner rubber; Special fabric knitting machine or winding machine shall be used for knitting and winding hose; Knitting machine is required for knitting hose. Huzhou Braided hose The basic production processes include rubber mix processing, cord fabric and canvas processing, rubber tube molding, vulcanization, etc. The manufacturer of acid and alkali resistant rubber hose said that the processing method of the skeleton layer and the forming equipment of the rubber hose are different for different structures and different skeletons.

Huzhou Braided hose The quality is closely related to the material selection and the manufacturing process. 1. The galvanized air ducts of different specifications are made of plates of different thicknesses according to the specification requirements. On the basis of being familiar with the size and layout of the air duct in the drawing, skilled technicians will set out and cut the material to ensure that the air duct production and installation meet the relevant standards. 2. The galvanized sheet air duct flange will be made uniformly according to the series of specifications specified in the drawing. In addition, the bolt holes of the flange will be punched at a fixed distance with a punch and a mold. The forming welding of the flange will also be positioned with a special mold to ensure that the air duct flange of the same specification has interchangeability. Compared with the traditional galvanized iron pipe made by hand, the round galvanized air pipe made by mechanism has the following advantages: (1) The round galvanized air pipe has good sealing performance. (2) Both strength and rigidity are good. (3) The ventilation resistance is small, the ventilation noise is small, and the round pipe is better than the square pipe. (4) The galvanized air duct is easy to install and has few connection points. (5) Circular production Braided hose High grade, beautiful appearance. Galvanized spiral duct is very suitable. Generally, galvanized air ducts are used, while stainless steel pipes are very suitable for galvanized spiral air ducts in corrosive and particularly humid places. Generally, galvanized air ducts are used, while stainless steel pipes are used in corrosive and particularly humid places.

production Braided hose It will burst for a long time due to frequent and severe pressure shocks. This situation is usually not caused by excessive static pressure, but is related to the strength and frequency of pressure shock. During the operation of construction machinery, the oil pressure in the oil resistant hose will rise or fall repeatedly, and then it will form frequent pressure shocks to the oil pipe, causing the oil seal of each part to become more damaged, the oil resistant hose will bubble and break, and the pipe joint will become loose and leak. Therefore, in the process of operation, the valve rod should not be pulled too hard, and it needs to be gentle. The application temperature of the oil in the oil resistant rubber hose is too high, resulting in aging and bursting of the rubber hose. During the operation of construction machinery, the hydraulic system will cause the oil to become hot due to power failure, and the influence of external temperature (especially in summer) will cause the oil temperature to rise sharply. The higher the oiling temperature is, the easier the rubber hose ages, the worse the elasticity is, the lower the strength and sealing function are, and the oil resistant hose will burst quickly. Therefore, Braided hose Where can I find it? During operation, when the temperature rise of the hydraulic system is too high or too fast, the causes should be found and eliminated in time. Necessary cooling measures shall be taken for summer operation, especially continuous operation.