With the rapid development of the national economy and the continuous improvement of the technical level, almost all walks of life need to do exhaust ventilation systems, Kunming Acid and alkali resistant rubber hose What are the advantages worth pursuing? 1. The welding method is unique. It adopts a new low temperature welding form, which does not damage the galvanized layer of the product. The welding spot is firm, the weld seam is beautiful, and the sealing is good. After welding, no treatment is required for the weld seam. 2. The manufacture of mechanically formed air duct makes the high-quality galvanized sheet not damaged, and the galvanized layer not damaged, thus prolonging the service life. 3. The specification is uniform and the size is standard, which ensures that the inner wall of the pipeline is flat and smooth, so that it is easy to clean and the material transportation is smooth. 4. The self forming flange can make the pipe material uniform, no longer use angle steel flange, and reduce the pipe weight by more than 20%, so the load bearing capacity of the building can be greatly reduced, thus reducing the overall cost of the building. 5. Enhance the beautiful pipeline, beautiful appearance, exquisite structure, smooth lines, superior performance, and the installation of exposed air ducts, especially suitable for this product. 6. Typical round air pipe fittings are generally 3-6 meters long and rectangular pipe fittings are 1-1.5 meters long, reducing the connection points of pipe fittings and minimizing the leakage at the joint of pipe fittings. 7. The pipe fittings, joints and spare parts made by mechanized assembly line all have standard sealing rings. As they are produced in a standardized and factory way, they have better air tightness. 8. Mechanically formed compression ribs and stiffeners can improve the strength of the pipe wall, save material thickness and reduce costs. The thickness of the seam of the spiral pipe is 4 times that of the pipe body, which makes the pipe very rigid and has the best pressure bearing performance, especially the negative pressure. 9. Scientific joint and seaming methods can ensure smooth pipeline gas without affecting pipeline flow diameter. Therefore, mechanized assembly line production improves production efficiency and effectively shortens delivery cycle. Advanced computer process control program blanking, production, Acid and alkali resistant rubber hose Where can I find it? It ensures the dimensional accuracy of pipeline components, thus ensuring fast and convenient installation and construction, and improving work efficiency and economic benefits.
Ventilation pipes on ships are generally made of galvanized iron sheet high quality Acid and alkali resistant rubber hose This kind of air duct is generally made by hand, and the production efficiency is low. Later, circular spiral air ducts made by machines greatly improved the production efficiency of air ducts and the quality of air ducts, which were widely used on civilian ships. However, for military ships with very strict height restrictions, circular air ducts obviously occupied more height than rectangular air ducts, which limited the promotion and use of circular spiral air ducts on ships. In the 1980s, 708 Research Institute, the Military Representative Office of Navy Garrison 426 Factory and Dalian Bohai Air Conditioning Auxiliary Factory jointly successfully trial produced the flat spiral air duct. It combines the advantages of the circular spiral air duct and the rectangular air duct. It is the third generation of air duct for ships, which is welcomed by the ship design department and has achieved good results after many ship use. The structure of the spiral air duct is the same as the round spiral air duct. It is also formed by rolling galvanized iron sheet on a special pipe coiler. Therefore, it can be produced mechanically, and the inner surface of the air duct is flat and smooth. The utilization rate of materials is also high. The thickness of galvanized iron sheet is generally 0.6mm. Although it is 0.75~slightly thinner than the commonly used rectangular air duct iron sheet, its rigidity is higher than that of rectangular air duct due to the reinforcement effect of spiral undercut. There are two types of flat spiral air duct: non adiabatic and pre adiabatic. Non adiabatic type is applicable to air conditioning ducts with simple mechanical ventilation, natural ventilation and external insulation. Kunming Acid and alkali resistant rubber hose There are two types, one is air layer insulation, that is, there is 12.5~thick air layer between the inner pipe and the outer pipe. The other is that the inner and outer pipes are filled with thermal insulation materials rock wool or ultra-fine glass wool to become good thermal insulation air conditioning ducts.
Air duct mainly refers to the ventilation duct of the central air-conditioning system, which is often ignored, but it is an important part of the air-conditioning system. Kunming Acid and alkali resistant rubber hose What are the regulations for welding air ducts? Gongfa HVAC is a manufacturer dedicated to the production of air ducts, which has been recognized and supported by the majority of users for many years. 1、 The welding regulations of carbon steel plate air duct are as follows: 1. The carbon steel plate air duct should be welded by DC welder. Introduction to welding air duct If AC welding machine is used for welding, a vibrator must be added to reduce excitation and stabilize the arc. When welding steel plates, the arc is unstable, which can lead to deterioration of weld quality. 2. Before welding, remove the dirt, oil stain and rust at the welding port; When spot welding or continuous welding is used, the oxide shall also be removed. The butt joint shall be kept with the minimum gap, and the overlap at the manual spot welding location shall be removed in time. After welding, the electrode slag and residual welding wire in the weld and its surrounding area shall be removed in time. 2、 The welding regulations of stainless steel air duct are as follows: 1. Before welding the air duct, remove the grease and dirt in the weld area to prevent pores and sand holes in the weld. Cleaning can be carried out with gasoline, acetone, etc. When welding stainless steel plates by electric arc welding, the surfaces on both sides of the weld should be coated with white ash, Kunming Acid and alkali resistant rubber hose To avoid welding slag splashes adhering to the surface of the plate. 2. After welding, attention shall be paid to removing the slag at the weld, brushing the metal luster with a copper wire brush, pickling with 10% nitric acid solution, and then cleaning with hot water.
The air conditioning in the hall of a giant building is provided by the 6FWB unit fixed in the basement. high quality Acid and alkali resistant rubber hose The vibration of the unit is transmitted to the ground hall through the bridge connecting the sand blasting hose pipe, and the noise value reaches 45dB. In such an environment, people always feel uncomfortable. After the improved design, sandblasting rubber pipes were connected in series on the connecting pipes, which not only absorbed some of the noise generated by the unit vibration, but also the noise generated by the fluid pulsation in the pipeline system. At this time, the noise value in the ground hall was only 33dB, greatly improving the environment in the hall. The movable cylinder on the vulcanizing press will move upward and downward for the need of loading and unloading the mold. After repeated reciprocating movements, the copper serpentine will suffer from fatigue fracture. Although it can still be used after repair, it will cause time loss if it is stopped for repair. Acid and alkali resistant rubber hose Where can I find it? Although it has good soft properties and strong fatigue resistance, it is weak in pressure bearing, temperature resistance, aging resistance and other aspects, and can not continue after several months of use. The good comprehensive performance of sand blasting hose is fully reflected here. In the general industrial field, in addition to pressure and temperature, there are often severe conditions such as fatigue, corrosion, vibration, compression, impact, etc. Under such circumstances, it is most appropriate to use sandblasting hose to compensate for the position movement of the pipeline.
People buy in daily life high quality Acid and alkali resistant rubber hose Take it home for installation. It is obviously installed very well, but the spiral air duct will become loose for a long time, which gives most users a headache. So what is the problem with spiral air duct reinforcement? This is of course necessary. The following manufacturer of galvanized spiral air duct will give you a detailed introduction. 1. Reinforcement measures shall be taken for circular pipes (excluding spiral pipes) with a diameter greater than or equal to 80 mm, a section length greater than 1250 mm or a total area greater than 4 ㎡; 2. The side length of rectangular air duct is more than 630 mm, the length of pipeline insulation side is more than 800 mm, the section length is more than 1250 mm, or the plane area of one side of low pressure pipeline is more than 1.2 m2, and that of medium and high pressure pipeline is more than 1.0 m2, so reinforcement measures should be taken; 3. For reinforcement of irregular oval pipes, the reinforcement method of rectangular pipes shall be referred to. The spiral air duct manufacturer Hongyuansheng Electromechanical also has something to say: the reinforcement of galvanized air duct non-metallic air duct should also meet the following requirements: when the diameter or side length of the rigid PVC pipe is greater than 500 mm, the connection between the pipe and the flange should be equipped with stiffening plates, and the spacing should not be greater than 450 mm. The reinforcement of organic and inorganic FRP pipes shall be made of the same materials with the same anti-corrosion performance as the pipes themselves. Acid and alkali resistant rubber hose Where can I find it? The manufacture of rectangular pipe elbows shall generally adopt concentric arc elbows with the curvature radius of the length inside and outside the plane. When other forms of elbow are used, and the plane length is more than 500 mm, the elbow deflector shall be set.
