Sand suction hose Where can I find it? Precautions ① The acid and alkali resistant rubber hose used shall not only be oil resistant, but also be pressure resistant, heat resistant, cold resistant, wear resistant and aging resistant. ② The rubber hose should not be too long or too short, generally 1.4 meters. ③ The interface is tight and can be fastened with thin iron wire or clip to prevent falling off and air leakage. ④ It is forbidden to pull acid and alkali resistant rubber hose from one room to another or through walls, floors and floors to prevent accidents caused by rubber hose breaking and falling off. ⑤) The acid and alkali resistant rubber hose should be placed in a place where it can be seen frequently, so that it is easy to detect leakage. Check whether the rubber hose leaks after each bottle change. ⑥ Do not replace acid and alkali resistant rubber hose with universal rubber hose. Since the full rubber hose does not contain a skeleton layer, it is only necessary to use a press out machine to press out the hose; The cloth clamping hose needs to use a molding machine that wraps the adhesive tape on the inner adhesive layer; When forming the suction hose, first wrap the metal spiral wire and then wrap the inner rubber; Special fabric knitting machine or winding machine shall be used for knitting and winding hose; Knitting machine is required for knitting hose. Guizhou Sand suction hose The basic production processes include rubber mix processing, cord fabric and canvas processing, rubber tube molding, vulcanization, etc. The manufacturer of acid and alkali resistant rubber hose said that the processing method of the skeleton layer and the forming equipment of the rubber hose are different for different structures and different skeletons.

Guizhou Sand suction hose Prevention of vibration and noise during installation: the prevention of vibration and noise during installation is a key point in the installation process. The prevention of vibration and noise of spiral air duct during installation is mainly from the following aspects: 1. The fan and spiral air duct are connected by hose, and the hose at the suction inlet of the fan shall be installed with appropriate tightness, Avoid noise and vibration caused by reducing the area of air inlet and outlet due to loose soft connection. 2. The spiral air duct shall be made, installed and connected with the components. The connection shall be tight to reduce the gap and avoid air leakage noise. 3 In order to prevent the spiral air duct from vibration, fixed supports shall be installed at the turning of each system spiral air duct and at the connection with the ventilator and the air outlet for shock absorption. 4 The vibration damping device shall be set according to the design requirements or construction specifications during fan installation. Air leakage rate test of spiral air duct After the installation of spiral air duct, air leakage rate test is required. According to the specifications, the air leakage rate test of spiral air duct adopts the combination of light leakage legality and quantitative air leakage rate test. The light leakage method is suitable for the tightness test of medium and low pressure systems; The air leakage rate test is suitable for sampling inspection of medium pressure system and full detection of high pressure system. Light leak detection of spiral air duct Light leak detection is a qualitative method to detect the tightness of the spiral air duct of the system by using the strong penetration of light to holes. The test method is to use a bulb with protective cover whose voltage is not higher than 36V and power is more than 100W in the spiral air duct on a certain length of spiral air duct in dark environment, and slowly move from one end of the spiral air duct to the other end. If light can be observed outside the spiral air duct during the test, it indicates that there is a leak point in the spiral air duct, and repair the leak point of the spiral air duct. Sand suction hose Where can I find it? The light leak detection method of the low-pressure system adopts the method of subsection detection and summary analysis. The spiral air duct of the tested system is not allowed to have multiple obvious light leaks in the form of slits. The spiral air duct of the low-pressure system has no more than two light leak points every 10 meters, and the average joint of 100 meters is no more than 16; For every 10 joints of spiral air duct of medium pressure system, no more than 1 light leak point, and no more than 8 joints per 100 meters are qualified.

production Sand suction hose The inner and outer walls are smooth, the resistance of the air duct is small, the secondary noise is not generated during air supply and exhaust, the energy consumption is reduced, and the operation cost is saved. The product can be made on site, cut, drilled, and opened, the installation is simple, and the labor and time are saved. The user's investment cost is reduced, the construction period is shortened, the performance price ratio is high, and it is cheaper than other materials. After the installation is completed, no maintenance is required, and the maintenance cost is reduced. The key points of whether galvanized sheet air duct material galvanized sheet is corroded are mainly reflected in the following three aspects: ① The first corrosion of galvanized sheet in the entire service life cycle is the oxidation of the galvanized layer on the surface, resulting in white rust. After a little longer time, the white rust on the surface further reacts with carbon dioxide and other impurities in the humid air to form black spots. When the galvanized sheet is used for a long time and the galvanized layer is severely corroded, the steel base loses the sacrificial anti-corrosion effect of zinc, and begins to oxidize to generate red rust. Once the steel base begins to oxidize, the corrosion rate becomes very fast, and the life of galvanized sheet ends. ② In addition, there are two special corrosion conditions of galvanized sheet, namely, black stain. One is that after being used for a period of time, due to the influence of lead and other elements in the zinc coating, the galvanized sheet will become black in the matte part of the zinc flake. The blackened zinc coating still has a protective effect on the steel base, but has a certain impact on the service life. ③ Sand suction hose Where can I find it? It has excellent corrosion resistance in dry or pollution-free environment. However, in the polluted environment, the service life will be greatly shortened, so it is necessary to pre coat the film into color plates before use.

Sand suction hose Where can I find it? It has become the standard configuration of the modern new ball mill, but many problems may occur during the use or installation of the rubber lining plate, which will cause the failure of the rubber lining plate of the ball mill. Here is a brief introduction to the causes of the more common failure of the rubber lining plate of the ball mill. The design and installation are not professional and reasonable. The design and installation are also common problems for many novice manufacturers. For example, the bolt holes for fixing the ball mill lining plate are square, which will cause stress concentration and fracture. Adjust the size of lining plate to control the gap between lining plates at about 8mm; The installation quality of lining plate is very important to the safe operation of ball mill. First, tighten the fixed wedge symmetrically, put the lining plate in sequence, and then use the tightening wedge to secure it; Therefore, professional installation guidance can easily avoid these problems. The reason why the rubber lining plate of the ball mill does not match the steel ball is relatively common, and it is easy for many novice manufacturers to ignore and make mistakes. During the operation of the ball mill, the rubber lining plate of the ball mill, materials and steel balls promote the normal grinding and crushing of the ball mill due to the interaction of forces. The hardness of materials is related to wear resistance, and the wear resistance increases with the increase of hardness, Guizhou Sand suction hose It is a pair of friction pairs, and the increase of hardness of one side will cause the wear of the other side to increase. Therefore, the high wear-resistant rubber lining plate is matched with the high wear-resistant steel ball, and the low wear-resistant rubber lining plate is matched with the low wear-resistant steel ball, so as to ensure the normal wear of the rubber lining plate of the ball mill and extend the service life of the ball mill.

Common for ventilation duct production Sand suction hose What should be paid attention to during processing: the galvanized air duct shall not be connected with s-shaped, c-shaped right angle and vertical angle plugs. Clasp type air duct shall not be used for Grade 1 to 5 clean air. The rivet spacing of air duct shall be less than 100 mm. When the air purification level is 1-5, the rivet spacing of air duct shall be less than 65 mm. Before processing the galvanized air duct, use cleaning solution to remove the oil stain and dust on the surface of the plate. The cleaning solution shall be a neutral detergent, which will not damage the board surface, and will not produce dust after drying, so it will not be harmful to human health. Clean the vent pipe with cleaning solution after fabrication. After cleaning, the electric board shall be sealed in time after the white silk cloth cleaning inspection meets the requirements. The inner wall of color coated steel pipe shall be smooth, and the coating shall not be damaged during steel plate processing. The damaged parts shall be coated with epoxy resin. The galvanized air duct seamed joints, riveted joints and flange flanged corner joints shall be sealed with sealant or other sealing measures according to the design and cleaning level requirements. The sealing materials shall be isobutyl rubber, chloroprene rubber, modified silica gel, etc. The sealing surface of the air duct plate joint shall be located at the positive pressure side of the air duct wall. The production site of galvanized air duct shall be relatively closed, and the production site shall be paved with soft materials that are not easy to produce dust. The galvanized air duct shall have fewer longitudinal joints, glass fiber reinforced plastic ventilation pipes, and no transverse joints. Sand suction hose Where can I find it? The processing of connecting bolts, nuts, washers and rivets shall be galvanized or other anti-corrosion measures, and blind rivets shall not be used.

The so-called acid and alkali resistant rubber hose is the rubber hose used to transport acid and alkali solutions, which can be divided into production Sand suction hose , acid and alkali resistant cloth clip hose, etc; In actual production, using a certain proportion of recycled rubber for acid and alkali resistant rubber hose can not only reduce the cost of raw materials, but also improve the aging resistance of rubber compound, thus extending the service performance and service life of acid and alkali resistant rubber hose. However, if you want to significantly improve the aging resistance of acid and alkali resistant hose, it is impossible to rely solely on recycled rubber, and rubber antioxidant is essential. What anti-aging can be used in acid and alkali resistant hose? 1. Antioxidant A: Antioxidant A, namely, antioxidant A, is in the form of yellowish brown to purple crystal blocks at room temperature. It is a universal antioxidant, which has good resistance to heat, oxygen, flexion, weather and fatigue aging. It also has a certain inhibitory effect on harmful metals. It is easy to disperse in the rubber compound, and has no obvious impact on the processing performance of the rubber compound and the physical and mechanical strength of the vulcanizate, It is the preferred antioxidant product in the production of acid and alkali resistant hose. It can also be used as a stabilizer in the acid and alkali resistant hose containing styrene butadiene rubber, which can significantly delay the aging time of acid and alkali resistant hose. 2. Antioxidant D: antioxidant D, namely N-phenyl - β－ Naphthylamine (D) is a kind of heat aging resistance commonly used in the production of rubber products, Sand suction hose Where can I find it? Anti aging agent resistant to fatigue aging; Due to the poor heat resistance of the acid and alkali resistant hose, the use of a small amount of antioxidant D in the protection system can improve the heat aging resistance of the rubber compound, thereby improving the heat resistance of the acid and alkali resistant hose, expanding the use temperature range, and extending the use time.