Common for ventilation duct wear-resisting Air compression hose What should be paid attention to during processing: the galvanized air duct shall not be connected with s-shaped, c-shaped right angle and vertical angle plugs. Clasp type air duct shall not be used for Grade 1 to 5 clean air. The rivet spacing of air duct shall be less than 100 mm. When the air purification level is 1-5, the rivet spacing of air duct shall be less than 65 mm. Before processing the galvanized air duct, use cleaning solution to remove the oil stain and dust on the surface of the plate. The cleaning solution shall be a neutral detergent, which will not damage the board surface, and will not produce dust after drying, so it will not be harmful to human health. Clean the vent pipe with cleaning solution after fabrication. After cleaning, the electric board shall be sealed in time after the white silk cloth cleaning inspection meets the requirements. The inner wall of color coated steel pipe shall be smooth, and the coating shall not be damaged during steel plate processing. The damaged parts shall be coated with epoxy resin. The galvanized air duct seamed joints, riveted joints and flange flanged corner joints shall be sealed with sealant or other sealing measures according to the design and cleaning level requirements. The sealing materials shall be isobutyl rubber, chloroprene rubber, modified silica gel, etc. The sealing surface of the air duct plate joint shall be located at the positive pressure side of the air duct wall. The production site of galvanized air duct shall be relatively closed, and the production site shall be paved with soft materials that are not easy to produce dust. The galvanized air duct shall have fewer longitudinal joints, glass fiber reinforced plastic ventilation pipes, and no transverse joints. Air compression hose Where can I find it? The processing of connecting bolts, nuts, washers and rivets shall be galvanized or other anti-corrosion measures, and blind rivets shall not be used.

wear-resisting Air compression hose Or PVC steel wire spiral reinforced pipe. The commodity is made of high-quality PVC plastic raw materials. PVC steel wire reinforced pipe is also a PVC steel wire reinforced hose that uses steel wire reinforcement. The embedded spiral steel wire is used as the reinforcement layer, so the product has both rigidity and flexibility, that is, it has both satisfying mechanical properties and rigidity, and excellent flexibility. The reinforced pipe of latex fiber is PVC hose embedded with steel wire framework. The inner and outer tube walls are clear, lubricated, free of bubbles, and the fluid transportation is clearly visible. Silicone fiber tube is resistant to low concentration of acid and alkali, high elasticity, not easy to age, and has a long service life. Resistant to high pressure and can be kept intact under high pressure and vacuum. PVC steel wire pipe is made of new PVC reinforced materials, and has made great progress in compressive strength and hardness. The main production method of silica gel steel wire pipe is multiple production method. The main types of steel wire pipe in shopping malls include high pressure steel wire pipe, low pressure steel wire pipe, steel wire skeleton pipe and Tongming steel wire pipe. The application methods are different in different environments. The new PVC steel wire pipe is the most widely used commodity today. Air compression hose Where can I find it? After use, it will not be the same as the metal pipe, which is easy to deform and leak. What advantages does the PVC fiber reinforced pipe have.

We all know Air compression hose Where can I find it? The noise pollution in industrial production is very serious, and noise pollution is also an important factor affecting workers' enthusiasm for production. Ball mills were once a major source of noise in mining equipment. In order to reduce the noise generated by ball mills, protect the physical and mental health of workers, improve workers' enthusiasm for production, and create greater profits for the company, Through the efforts and research of domestic and foreign industry experts, the ball mill liner has been transformed. Through repeated tests and comparison, it is found that the noise generated by the rubber liner and the manganese steel liner of the ball mill is far less than the manganese steel liner when the technical parameters are up to standard. According to the data provided by the noise monitoring station and the concentrator, We analyzed the noise intensity and the economic benefits: the domestic ND2 precision sound level meter and octave filter were used for detection, and the sound level meter was calibrated by the provincial sound level meter measurement and verification station; There is no sound insulation room in the ball mill workshop. The monitoring points are arranged according to the position of the ball mill and the flow of workers to observe the mechanical operation, 2m away from the sound source. One monitoring point is respectively set on the left and right of the east and west of the workshop and in the middle of the two ball mills. The measurement method is in accordance with the Noise Detection Specification for Industrial Enterprises. As the noise in the workshop is continuous and steady, sound level A is used as the evaluation basis. The rubber lining plate is manufactured by Hainan Rubber Lining Plate Factory according to the ball mill shell structure and the original manganese steel lining plate specification (1.4mx0.74mX0.07m). Liaocheng Air compression hose First, take out the manganese steel lining plate in the ball mill barrel, and then install the rubber lining plate in the barrel in turn (front and back). Each ball mill is installed with 48 pieces. First, use the pressure strip to compress, and then use the screws to fix the rubber lining plate on the ball mill barrel, so as to prevent falling off when rotating. The noise intensity of the ball mill workshop with manganese steel liner is 94-103dB (A), while the noise intensity of the ball mill workshop with rubber liner is 87-92dB (A), and the noise reduction difference is 7-11dB (A). The rubber liner has good noise reduction effect.

What is stainless steel spiral duct? Air compression hose Where can I find it? The products are mainly used to connect the air flow between two places and play the role of ventilation. There are three types of galvanized spiral air ducts, stainless steel spiral air ducts and composite spiral air ducts. Here we mainly talk about the stainless steel spiral air duct, and briefly analyze the reason why it is widely used in villas. The so-called stainless steel air duct is strictly a kind of air duct processing technology, also known as spiral seamed thin-walled tube. The best quality is the thin-walled tube with spiral seamed made of metal strips. Because the applied material is metal, it is also called spiral seamed metal tube. It was first used in the military industry of western countries, such as ships, ship ventilation, air conditioning systems, and later used in trains Subway, mine and other civil facilities. By 2000, according to statistics, 95.6% of office buildings, shopping malls and subways in the United States had applied spiral air ducts. In civil residential buildings, 72.5% of central air conditioners use spiral air ducts. Since the mid-1990s, China has introduced this technology into the shipbuilding industry. With the rapid development of China's economy, the use of central air conditioners has increased year by year, and the quality of auxiliary products for exhaust and air supply has been continuously improved. Spiral air ducts have been widely used in some villas. (1) Product standardization: The production of spiral round air duct fittings (pipe fittings and joints) has been highly automated, systematic, and has industrialized quality control. It is well known that the wind resistance of circular duct is much smaller than that of rectangular duct. (2) Easy to install. The installation of spiral air duct significantly reduces the connection points between pipes and minimizes the leakage at the joint of pipe fittings. The typical spiral air duct is 3~6m long, while the typical rectangular air duct is only 1~1.5m long; The connection of two spiral air ducts requires only one pipe connector, while the connection of traditional rectangular air ducts often requires a completely independent double flange system. (3) Usually only small installation space is required: the same wear-resisting Air compression hose The circular pipe with a diameter of 200mm in the installation space can replace 250 × 150mm rectangular pipe. On the premise of not increasing additional installation space, several parallel circular pipes can replace flat rectangular pipes.

Liaocheng Air compression hose The quality is closely related to the material selection and the manufacturing process. 1. The galvanized air ducts of different specifications are made of plates of different thicknesses according to the specification requirements. On the basis of being familiar with the size and layout of air duct in the drawing, skilled technicians shall set out and cut materials to ensure that the production and installation of air duct meet relevant standards. 2. The galvanized sheet air duct flange will be made uniformly according to the series of specifications specified in the drawing. In addition, the bolt holes of the flange will be punched at a fixed distance with a punch and a mold. The forming welding of the flange will also be positioned with a special mold to ensure that the air duct flange of the same specification has interchangeability. Compared with the traditional galvanized iron pipe made by hand, the round galvanized air pipe made by mechanism has the following advantages: (1) The round galvanized air pipe has good sealing performance. (2) Both strength and rigidity are good. (3) The ventilation resistance is small, the ventilation noise is small, and the round pipe is better than the square pipe. (4) The galvanized air duct is easy to install and has few connection points. (5) Circular wear-resisting Air compression hose High grade, beautiful appearance. Galvanized spiral duct is very suitable. Generally, galvanized air ducts are used, while stainless steel pipes are very suitable for galvanized spiral air ducts in corrosive and particularly humid places. Generally, galvanized air ducts are used, while stainless steel pipes are used in corrosive and particularly humid places.

At present, the common air ducts in the domestic market are generally made of galvanized iron sheet, commonly known as white iron sheet. wear-resisting Air compression hose And the thickness is 0.44~1.22mm. The thickness of iron sheet of air duct in China is generally less than 1.5mm, and the thickness of zinc coating refers to the national standard GB/T 13912-2002: 35 μ m. Average 45 μ m。 During the production of galvanized air duct, the national standard requires us to understand the following figures: 1. Appearance: conduct appearance inspection on all hot galvanized parts, and the main surface should be smooth, free of falling off, roughness and zinc spikes (if these zinc spikes will cause damage), free of peeling, missing plating, and residual solvent residue, There shall be no zinc lump and zinc ash in the parts where hot galvanized workpieces are used or where they are corrosion resistant. Note: "Roughness" and "smoothness" are relative concepts, and the coating roughness of workpiece is different from that of mechanical roller or (and) blow molding and galvanized products (such as galvanized steel plate and galvanized steel wire). As long as the coating thickness is greater than the specified value, there may be dark or light gray uneven areas on the surface of the plated parts. White rust (mainly white or gray corrosion products of alkaline zinc oxide) is allowed on the surface of galvanized workpieces stored in wet conditions. 2. Thickness: quantitative sampling shall be carried out according to the specified test method for coating thickness test. According to the size of the main surface area of hot-dip galvanized parts, the coating thickness measured in the test shall meet the following requirements: A) For parts with the main surface area greater than 2m (i.e. large parts), the average coating thickness measured on all basic measured surfaces of each part in the sample shall not be less than the minimum value of the corresponding average coating thickness: B) For parts with the main surface area less than 2m, Air compression hose Where can I find it? The local coating thickness measured on each basic measuring surface shall not be less than the minimum local thickness, and the average coating thickness measured on all basic measuring surfaces of the sample shall not be less than the corresponding minimum average thickness.