Changchun Air compression hose With the continuous updating of technology, the products are also developing in the continuous updating. At present, the inspection requirements of rubber hose are also improved compared with the previous ones. The inspection index of ultra-high pressure hose shall meet the following index requirements according to the requirements of the Safety Code for High Pressure Water Jet Cleaning Operation: 1) The bursting pressure shall be more than 2.5 times of the working pressure. 2) The test pressure shall be 1.5 times of the working pressure, and the pressure shall be kept for more than 2 minutes without damage. 3) Pulse pressure shall be within the range from zero to working pressure, and 50000 pressure pulses shall be free of damage; The pulse frequency is 15 times/min when the working pressure is 1000-2800bar, and 110 times/min when the pressure is above 2800bar. Since high-pressure cleaning machine has been widely used in all walks of life, and the working condition of high-pressure hose is relatively the worst, we must pay attention to the quality when selecting high-pressure hose, so as to avoid unnecessary safety accidents. Air compression hose company The development of rubber hose can not be separated from cooperation, R&D and innovation can not be separated from communication, and the inspection requirements of rubber hose have been improved compared with the previous ones. The storage site shall be free of ozone, heat source and equipment generating electromagnetic field. The coiled hoses or hose assemblies shall be stored horizontally, and the stacking height shall be limited to the extent that the products at the bottom will not produce permanent deformation.
Changchun Air compression hose Also called pu steel wire pipe, ventilation pipe, dust removal pipe, dust collection pipe, dust conveying pipe, industrial powder dust collection pipe, sweeping car dust collection pipe, drilling machine dust collection pipe, woodworking dust collection pipe, collectively called dust collection pipe. Therefore, industrial food dust transportation and industrial dust transportation are used for dust collection pipe. The production process structure of copper plated steel wire dust collection pipe is to wrap the pipe wall with solid elastic copper plated steel wire spirally, and the pipe wall material is coated with copper plated steel wire with special polyether PUR. PUR material is also called PU material. The thickness of pipe wall can be 0.4mm, 0.6mm, 0.9mm, 1.2mm, 1.5mm, 1.8mm and 2.1mm, depending on the customer's needs. Such as the temperature, wear resistance, flexibility and bending, hydrolysis resistance of the dust collection pipe. It is also necessary to consider whether static electricity is generated in the process of pipe full conveying dust to avoid unnecessary dust explosion and fire. Copper plated steel wire plastic coated dust collection tube is suitable for vacuum suction of powder and particle in industrial and mining, agriculture and water conservancy, civil engineering, food, petroleum, chemical industry, health and other industries, as well as transportation of water, oil, chemical materials, food, etc. Abrasive solids such as dust, powder, fiber, chip and particle, gas and liquid environment, for dedusting and suction plant, Air compression hose company Industrial vacuum cleaners, paper and textile fibers, are used as protective tubes. It is widely used in farmland irrigation, industry and mining, oil depot, sand extraction, sand blasting, food, medicine, indoor gas, powder, dust absorption and emission and other fields. This product is a substitute for PVC, rubber and metal pipes.
People buy in daily life production Air compression hose Take it home for installation. It is obviously installed very well, but the spiral air duct will become loose for a long time, which gives most users a headache. So what is the problem with spiral air duct reinforcement? This is of course necessary. The following manufacturer of galvanized spiral air duct will give you a detailed introduction. 1. Reinforcement measures shall be taken for circular pipes (excluding spiral pipes) with a diameter greater than or equal to 80 mm, a section length greater than 1250 mm or a total area greater than 4 ㎡; 2. The side length of rectangular air duct is more than 630 mm, the length of pipeline insulation side is more than 800 mm, the section length is more than 1250 mm, or the plane area of one side of low pressure pipeline is more than 1.2 m2, and that of medium and high pressure pipeline is more than 1.0 m2, so reinforcement measures should be taken; 3. For reinforcement of irregular oval pipes, the reinforcement method of rectangular pipes shall be referred to. The spiral air duct manufacturer Hongyuansheng Electromechanical also has something to say: the reinforcement of galvanized air duct non-metallic air duct should also meet the following requirements: when the diameter or side length of the rigid PVC pipe is greater than 500 mm, the connection between the pipe and the flange should be equipped with stiffening plates, and the spacing should not be greater than 450 mm. The reinforcement of organic and inorganic FRP pipes shall be made of the same materials with the same anti-corrosion performance as the pipes themselves. Air compression hose company The manufacture of rectangular pipe elbows shall generally adopt concentric arc elbows with the curvature radius of the length inside and outside the plane. When other forms of elbow are used, and the plane length is more than 500 mm, the elbow deflector shall be set.
production Air compression hose The manufacturing of is highly automated and the production speed is very fast. The general air duct can produce 20~40 meters per minute. Due to the low price of its raw material galvanized strip steel compared with the whole galvanized steel sheet, and its factory production and specification standardization, the cost of spiral air duct is lower than that of rectangular air duct; In addition, the total cost of spiral air duct is low due to the less demand for supports and hangers and the less installation work. Since the four corners of rectangular air ducts are prone to turbulence, reducing the effective flow area, the spiral air ducts have good air fluidity and large effective flow area, so the secondary noise of spiral air ducts is low. Because the spiral air ducts are strong, the low-frequency noise caused by air duct vibration is smaller, the air flow performance is good, the system pressure drop is small, and the daily operation system consumes less power. Spiral air ducts in the market are generally divided into three categories according to their materials: galvanized spiral air ducts, stainless steel spiral air ducts and composite spiral air ducts. Among them, spiral air duct has the best quality and strong applicability, but its price is high. At present, the most widely circulated spiral air duct on the market is galvanized sheet. The galvanized sheet spiral air duct is basically the characteristic of stainless steel spiral air duct, but its price is only two thirds or even lower than that of spiral air duct. Changchun Air compression hose It is generally used in places where the external environment is relatively common and the requirements for air ducts are not too high. As the iron sheet is prone to chemical reaction in various environments, corrosion and rust will occur. However, zinc hardly changes in dry air. In humid air, dense basic zinc carbonate film will be formed on the surface of zinc. The spiral air duct is mainly coated with zinc on the iron sheet of the air duct to protect the iron sheet. The protective and decorative properties of zinc coating can be significantly improved after passivation treatment, dyeing or coating with light protecting agent.
Changchun Air compression hose 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Air compression hose company When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.
The reason why welded air duct has become the favorite of the market, Changchun Air compression hose Compared with the air duct made of traditional materials, it has obvious advantages in technology, energy conservation, environmental protection and economy. This product has been inspected, tested and proved by the National Building Materials Testing Center, the National Fire Building Materials Quality Supervision and Inspection Center, the National Air Conditioning Equipment Quality Supervision and Inspection Center, the National Non ferrous Metal Quality Supervision and Inspection Center and other relevant authorities, In addition, no smoke is generated in the fire, and the smoke density is only 4, which is 10 to 20 times that of other organic foam materials. In modern buildings, central air conditioning is very common, and ventilation ducts are an important part of the central air conditioning system. According to statistics, China's annual demand is about 100 million square meters, reaching 20 billion yuan. Among all kinds of air ducts, welded air ducts stand out for their unique excellent performance and cost performance, and are becoming the new favorite in the central air-conditioning market. The manufacturing of welded air ducts is highly automated and the production speed is very fast. Ordinary air ducts can produce 20~40 meters per minute. Due to the low price of the raw material galvanized strip steel compared with the whole galvanized steel sheet, and its factory production and specification standardization, the cost is lower than that of rectangular air ducts; In addition, the total cost is low due to the less demand for supports and hangers and the less installation work. Since the four corners of rectangular air duct are prone to turbulence, Air compression hose company The effective flow area is reduced. The technology of welded air duct is very close to the international level; In terms of supporting services, more and more enterprises like this company provide high standard services. If there are any suggestions, we hope to see more and more enterprises with a sense of mission for the development of the industry.
