At present, the common air ducts in the domestic market are generally made of galvanized iron sheet, commonly known as white iron sheet. wear-resisting Acetylene tape And the thickness is 0.44~1.22mm. The thickness of iron sheet of air duct in China is generally less than 1.5mm, and the thickness of zinc coating refers to the national standard GB/T 13912-2002: 35 μ m. Average 45 μ m。 During the production of galvanized air duct, the national standard requires us to understand the following figures: 1. Appearance: conduct appearance inspection on all hot galvanized parts, and the main surface should be smooth, free of falling off, roughness and zinc spikes (if these zinc spikes will cause damage), free of peeling, missing plating, and residual solvent residue, There shall be no zinc lump and zinc ash in the parts where hot galvanized workpieces are used or where they are corrosion resistant. Note: "Roughness" and "smoothness" are relative concepts, and the coating roughness of workpiece is different from that of mechanical roller or (and) blow molding and galvanized products (such as galvanized steel plate and galvanized steel wire). As long as the coating thickness is greater than the specified value, there may be dark or light gray uneven areas on the surface of the plated parts. White rust (mainly white or gray corrosion products of alkaline zinc oxide) is allowed on the surface of galvanized workpieces stored in wet conditions. 2. Thickness: quantitative sampling shall be carried out according to the specified test method for coating thickness test. According to the size of the main surface area of hot-dip galvanized parts, the coating thickness measured in the test shall meet the following requirements: A) For parts with the main surface area greater than 2m (i.e. large parts), the average coating thickness measured on all basic measured surfaces of each part in the sample shall not be less than the minimum value of the corresponding average coating thickness: B) For parts with the main surface area less than 2m, Acetylene tape Where can I find it? The local coating thickness measured on each basic measuring surface shall not be less than the minimum local thickness, and the average coating thickness measured on all basic measuring surfaces of the sample shall not be less than the corresponding minimum average thickness.
Heze Acetylene tape It is a kind of hose that can be used for sand pumping and sand suction produced with high abrasion resistant rubber. It is often used in sand blasting industry, cement, steel, minerals and other industries, but it is mainly used in river dredging, slurry transportation in mines, sand digging and sand taking and other industries to transport sharp granular solids or solid-liquid mixtures. Its product structure is composed of high wear-resistant layer, reinforced water pipe layer, skeleton steel wire and outer rubber. Today, Myers will introduce the application field of wear-resistant sand absorption rubber pipe. When the wear-resistant sand suction rubber pipe is applied in the mine pit, it is necessary to set a floating boat equipped with a sand pump in the mine pit, and use the floating sand suction rubber pipe to connect with the sand pump. The floating boat will float up and down with the rise and fall of the water level. It is required that the pipe body has good flexibility and good tear resistance and bending resistance. The offshore pipeline is connected by non floating sand suction hose until the pulp transportation destination. The overall pipeline is divided into two parts, one for surface use and the other for onshore use. The main raw material of these two kinds of hoses is high abrasion and corrosion resistant rubber, and cord reinforcement layer and steel wire skeleton layer are added in the pipe wall to ensure the pressure resistance and tear resistance of the hose. The connection mode is vulcanized flange connection, that is, the flange and the hose are a whole, so there is no need to worry about the flange falling off. Floating sand suction hose used on the water surface. This kind of hose is required to float on the water surface. Due to the large drop of the mine (100 meters) and the long conveying distance Acetylene tape Where can I find it? The hose shall have high pressure resistance, and the design pressure is 25 kg/cm2 according to the calculation. It should be considered that the floating ship will move up and down with the rise and fall of the water level and the wave will cause lateral displacement. Its internal structure is the same as the sand suction hose used offshore, except that a floating body is installed outside the hose.
wear-resisting Acetylene tape The manufacturing of is highly automated and the production speed is very fast. The general air duct can produce 20~40 meters per minute. Due to the low price of its raw material galvanized strip steel compared with the whole galvanized steel sheet, and its factory production and specification standardization, the cost of spiral air duct is lower than that of rectangular air duct; In addition, the total cost of spiral air duct is low due to the less demand for supports and hangers and the less installation work. Since the four corners of rectangular air ducts are prone to turbulence, reducing the effective flow area, the spiral air ducts have good air fluidity and large effective flow area, so the secondary noise of spiral air ducts is low. Because the spiral air ducts are strong, the low-frequency noise caused by air duct vibration is smaller, the air flow performance is good, the system pressure drop is small, and the daily operation system consumes less power. Spiral air ducts in the market are generally divided into three categories according to their materials: galvanized spiral air ducts, stainless steel spiral air ducts and composite spiral air ducts. Among them, spiral air duct has the best quality and strong applicability, but its price is high. At present, the most widely circulated spiral air duct on the market is galvanized sheet. The galvanized sheet spiral air duct is basically the characteristic of stainless steel spiral air duct, but its price is only two thirds or even lower than that of spiral air duct. Heze Acetylene tape It is generally used in places where the external environment is relatively common and the requirements for air ducts are not too high. As the iron sheet is prone to chemical reaction in various environments, corrosion and rust will occur. However, zinc hardly changes in dry air. In humid air, dense basic zinc carbonate film will be formed on the surface of zinc. The spiral air duct is mainly coated with zinc on the iron sheet of the air duct to protect the iron sheet. The protective and decorative properties of zinc coating can be significantly improved after passivation treatment, dyeing or coating with light protecting agent.
Heze wear-resisting In places that must be crossed or may rub with the mechanical surface when working, hose clamps or springs and other protective devices should be used to prevent the outer layer of the sandblasting hose from being damaged. Sand blasting hose shall be arranged to avoid heat source as far as possible and away from the performance of engine exhaust pipe. If necessary, sleeve or protective screen can be used to prevent the hose from being heated and deteriorated. When the sand blasting hose must be bent, the bending radius should not be too small, and should be greater than 9 times the outer diameter. There should be a straight line section greater than 2 times the outer diameter of the pipe at the joint between the rubber hose and the joint. How high-quality the products and equipment we use are, it is inevitable that there will be some large and small failures in the process of using them, which will more or less have a certain impact on our work. Just like the use of sandblasting hose, there are traces of its outer adhesive seam, problems must be solved, For this, we explained the following solutions: First, the used water cloth should be used according to the original elastic edge of the water cloth when it is reused. 2： When we wrap the water cloth around the seam of the sandblasting hose, we should apply sufficient and uniform pressure to the pipe body. 3. The water cloth with different widths should be selected according to the size of the outer diameter of the wrapped sandblasting hose (for hose with an outer diameter of less than 30mm, the width of the water cloth should not exceed 90mm). The overlapping width of the water cloth should be 3/5-2/3 of the width of the water cloth.
Let's take a look today Heze Acetylene tape How should the maintenance work be done? Firstly, the thickness of galvanized air duct splice plate shall be within the range specified in various specifications. If it is less than the thickness, it is easy to have defects such as cracking and wrinkling due to significant increase of bending force, abnormal damage of forming roll, overload of transmission system, boring, etc. Secondly, in the dedusting system: galvanized air ducts can be used for the collection and transportation of dedusting devices. In terms of air exhaust system: there is a large amount of smoke in the dining room, dining room and hotel kitchen, which needs air exhaust. The galvanized pipe is more appropriate, with good strength, economy and practicality. In air conditioning system: galvanized air duct can be pasted with thermal insulation materials, and the surface is beautiful. In bulk material transportation: in the pneumatic conveying system, some materials with fine loose particles can be transported by galvanized pipes, which has low cost and good effect. In the ventilation system: fresh air is supplied and discharged, harmful gases are discharged outdoors, and outdoor fresh air is sent indoors. The strength of stainless steel plate is greater than that of ordinary steel plate. When stainless steel plate is used for seaming, first of all, a forming test should be carried out to avoid overloading of equipment and excessive wear or mechanical problems. Due to the poor plasticity of aluminum plate, it is easy to crack when biting into forming. Forming test shall be conducted before construction. The last point is that the protection and decoration of the galvanized layer of the galvanized air duct can be significantly improved after passivation treatment, dyeing or brushing light protective agent. and Heze Acetylene tape The fire prevention function of is mainly reflected in that it is nonflammable, but it should be noted that whether the insulation layer is burned depends on the material. We recommend that galvanized air duct materials use nonflammable insulation materials such as centrifugal glass wool.
In the shipbuilding industry, radio industry, electrical industry, telecommunications industry, instrument industry, aviation industry, medical industry, etc., we often see acid and alkali resistant hose, then what is Heze Acetylene tape What about? If you want to know more, please read down! Acid and alkali resistant silicone hose is a kind of pipe specially used for power equipment, which uses acid and alkali resistant silica gel as the main raw material and tightly wraps the pipe wall with electrical grade polyethylene spiral wire. Due to the chemical inertia of acid and alkali resistant silica gel, this kind of pipe has good acid and alkali resistance performance and electrical performance, and is commonly used in the production of wires, cables and lead wires in extreme acid and alkali environments. Also called: acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose. Features: 1. High temperature resistance (250-300 ℃) and low temperature resistance (- 40-60 ℃); 2. Good acid and alkali resistance. Physiologically stable, able to withstand repeated harsh and disinfection conditions, resistant to ozone aging, light aging, weather aging and ultraviolet radiation. 3. Small resilience and permanent deformation (no more than 50% at 200 ℃ for 48 hours), breakdown voltage (20-25KV/mm), ozone resistance and UV resistance. Acetylene tape Where can I find it? Radiation resistance and other characteristics, 4. Good electrical performance, small change when exposed to moisture, water or temperature rise, even if the silica generated by short circuit combustion is still an insulator, which ensures that electrical equipment continues to work, so it is most suitable for making wires, cables and lead wires.
