Yinchuan Corbel tube The break of the sandblasting hose usually refers to the appearance and change of the crack of the sandblasting hose. The sandblasting hose has one or more cracks, but the cracks are neat. Another is that the internal bending cracks at the crack of the sandblasting hose are neat. The causes of different errors are different, and the treatment methods are also different. Therefore, in the process of using or protecting the sandblasting hose, the sandblasting hose should not be subject to changing torque. When installing the sandblasting hose, try to keep the axis of the two joints on the same plane to avoid twisting the sandblasting hose in use. Therefore, be careful with the application, and try not to make the sandblasting hose change excessively to avoid consumption. Sand blasting hose plays a very important role in the industry. Its inner rubber layer is added with carbon black, which can effectively eliminate static electricity and directly contact with compressed air and abrasives. The requirement for wear resistance is quite high. Once worn through, the reinforcement layer will be exposed, and the sand blasting hose will burst. The reinforcing layer of sandblasting hose is a pressure resistant layer, so production Corbel tube The material and layout of the reinforcement layer directly determine the pressure rating of the sandblasting hose. There are two common enhancement layers: cloth clip enhancement layer and surround enhancement layer. The sand blasting hose with an inner diameter of 50mm or more is mostly used in the construction occasions where the sand blasting pipe needs to be extended to reduce the pressure loss in the sand blasting hose and ensure the normal operation of shot blasting.
production Corbel tube Acid and alkali resistance: there is no obvious change after soaking in 44 solutions for 24 hours; Pressure resistance: under the pressure of 52.5 MPa, the pressure is stable for 5 minutes without leakage, the surface of the pipe body is not deformed, and the damage pressure is greater than 105 MPa; Heat preservation: place the pipe in an environment of 300-50 ℃, with clear water in the pipe for 20 minutes, and the temperature ratio inside and outside the pipe is 1:40. The wear-resistant sand blasting hose is a material conveying pipe. The wear-resistant sand blasting hose is a material conveying pipe. Common black, yellowish or transparent; Most of them are wrapped by external rubber packing belt, and the steel wire is usually set between the internal and external rubber for negative pressure operation. The utility model is mainly used for conveying liquid containing solid particles such as particles, gravel, cement, quicksand, concrete, gypsum, etc., and is suitable for various tunnel projects, shafts, tunnels, and other engineering operations. The inner rubber and outer rubber of sand blasting pipe made of ordinary materials are usually made of wear-resistant materials, most of which are nitrile rubber (acrylonitrile butadiene copolymer), styrene butadiene rubber (oil extended styrene butadiene rubber), etc., Or PARA rubber (trefoil rubber), the inlet hose has better performance. According to the working conditions and the degree of loss of material particles to the transmission medium, the sand blasting pipe is generally divided into light sand blasting pipe and heavy sand blasting pipe. Spiral wire will make them suitable for negative pressure environment. Light sandblasting pipe Light sandblasting pipe Light sandblasting pipe is usually used in marine sandblasting and quicksand operations. The ordinary inner rubber is made of wear-resistant nitrile rubber (NBR), while the outer rubber is wrapped with composite rubber. Heavy sandblasting pipe Heavy sandblasting pipe Heavy sandblasting pipe is used for sandblasting sand, pebble, mud, etc. Equipment. Corbel tube company Sand blasting vacuum tube Sand blasting vacuum tube The sand blasting vacuum tube is embedded with spiral steel wire, and the general vacuum negative pressure can reach 0.9 bar. Common parameter definitions The wear-resistant sandblasting pipe generally has the following parameters: folding pressure is generally within 12 bar, higher sandblasting pressure can reach 36 bar, and sometimes vacuum negative pressure parameters such as 0.8 bar~0.9 bar are required.
Yinchuan Corbel tube It is widely used in mining, chemical industry, construction and iron and steel fields. At present, 90% of ball mills, rod mills and moistening mills on the market still use manganese steel cylinder liners, and the manganese steel material consumed on liners alone every year is more than one million tons. The emergence of rubber liners is favored by many big customers in the ball mill field. What are the indexes that affect the rubber lining plate of the ball mill? 1. Conditions of ball mill use scenario The feeding particle size of ore also plays an important role, so a good ball mill rubber lining plate will be designed according to the size of the customer's mill, feeding particle size, and steel ball diameter. Select the rubber formula suitable for customers, and carry out mapping, design, testing and processing. 2. Rubber formula and processing technology: The rubber material and formula directly affect the performance of the rubber lining plate of the ball mill. Wear resistance is a key factor. It is impossible to determine how long its service life is because of the impact of industrial and mining conditions. The second is corrosion resistance. This is the characteristic of the formula, so even if the appearance is the same, the performance is an advantage. Do not buy for cheap. 3. Regular maintenance: everyone knows that the rubber lining plate of the ball mill is fixed to the cylinder by means of T-bolts, so it is also very important to regularly check the tightness of the bolts and the wear of the rubber strips inside the cylinder. In order to avoid damaging the rubber lining plate of the cylinder and the cylinder of the ball mill when the lifting strip is worn out, the gain is not worth the loss. Corbel tube company One of the advantages of the manganese steel lining plate is that the replacement is simple and only needs two people to operate, and it can be replaced wherever it is broken. This is an advantage that the manganese steel lining plate does not have.
I, production Corbel tube Quantitative display of quality. In the evaluation plan prepared by the Ministry of Health and Social Insurance for the medical and health system, some indicators were put forward for the service quality of the hospital, such as the number of deaths before and after the operation, the number of unplanned rehospitalization, the infection rate of patients in the hospital, and the immunization rate. It can be seen that the quantification of quality is to reflect the quality of things through a series of quantitative analysis and synthesis. Sand blasting hose enterprises use public opinion polls to measure benefits and service quality. Since the purpose of administrative activities is to meet the needs of society or the public, the best way to measure the social effect and quality is to face the service objects, understand their evaluation and their satisfaction. Although popular, public opinion polls also have limitations, such as high cost, which is difficult to be accurate and reliable due to the influence of public judgment. In addition, the satisfaction of beneficiaries does not answer the question - is this service provided to those who need it most? III, Corbel tube company Administrative departments and public service institutions with single business nature. For those departments that have applied the quality assurance system, their performance evaluation only pays attention to efficiency and economy.
Corbel tube company The following recommendations contain a series of precautions to prevent items from aging to a greater extent during storage. 1. During storage, the rotating plan system shall be adopted to shorten the storage time of high-pressure braided hose as much as possible. If long-term storage cannot be avoided and the following recommendations cannot be followed, high-pressure braided hoses should be thoroughly inspected before use. 2. Physical storage conditions: The high-pressure braided hose must be stored without mechanical pressure, including excessive stretching, compression or deformation, and without contact with sharp or sharp objects. High pressure braided hoses should be stored on suitable supports or on dry ground. High pressure braided rubber tubes packaged as coils must be stored horizontally. High pressure braided rubber pipes shall not be stacked. If stacking cannot be avoided, the stacking height shall not cause permanent deformation of the high-pressure braided rubber pipe below. Pumping high-pressure hydraulic hose is a common high-pressure hydraulic hose. In order to ensure the operation safety of the pumped high-pressure hydraulic hose, the following small series will briefly introduce the correct use of the pumped high-pressure hydraulic hose: 1. Before each use of the high-pressure hydraulic hose, the surface of the high-pressure hydraulic hose must be evenly coated with soap liquid, which can play a non bonding role between the high-pressure hydraulic hose and the concrete, and play a lubricating role in the drawing process, It can greatly increase the reuse times of high-pressure hydraulic hoses. 2. Installation: first, insert the steel hinge wire into the inner hole of the draw tube to avoid extrusion deformation when pouring concrete. Then, pull out the high-pressure hydraulic hose coated with soap liquid from the prestressed hole and fix it in the correct position with a fixing ring. The spacing of the retaining rings is controlled by the suspension and is usually about 500 mm. production Corbel tube When connecting the high-pressure hydraulic hose, wrap both ends of the high-pressure hydraulic hose for one and a half weeks or two weeks with thin iron sheet or PVC pipe (vertical cutting), fix them with iron wire, and then seal both ends of the PVC pipe with tape to avoid entering the mortar.
The hard core method adopts the core extrusion process to extrude the inner rubber tube blank, which directly uses the extruder to cover the inner rubber tube blank on the iron core, instead of the traditional casing process, and simplifies the process flow. Yinchuan Corbel tube The billet forming adopts the process method of intertwining outer film and steel wire braiding forming. Similar to wrapping water wrapped cloth, the overlapping width is 1/2 of the film width. This process method can replace the method of wrapping outer film by extruder or by hand, reducing energy consumption and cost. We all know that the reinforcing layer and reinforcing layer of the rubber hose are the main force bearing parts, which are used to bear the load pressure. The factors determining the stress condition of the reinforced layer of the rubber hose are determined by the tension of the braided steel wire and the braiding angle. The high-speed steel wire hose braiding machine developed by our factory has introduced the advanced technology of foreign braiding production lines, and integrated the characteristics of domestic braiding machines. It integrates the advanced functions of hydraulic brake hose braiding production line, such as horizontal mechanical transmission, automatic lubrication, and so on, to develop equipment with high productivity and high degree of automation. The range of braiding diameter can be achieved Ф 6— Ф 25 Long core rubber hose (reinforcement layer). It fills the gap of domestic knitting production equipment, which can be widely used in rubber and plastic hose, rubber hose (reinforcement layer) knitting production equipment. The structure of high-pressure rubber hose is composed of four parts: inner liner, inner rubber layer, skeleton layer, middle rubber layer and outer rubber layer. Corbel tube company In case of direct contact with the conveying medium, the synthetic rubber with good medium resistance, high tensile strength, high constant tensile stress, small compression permanent deformation and easy processing is usually selected. In order to meet the use requirements of strong polar medium resistance, the inner liner is composed of polytetrafluoroethylene layer and rubber layer, and a layer of film or adhesive is added on the surface of the inner liner to improve the adhesion with the skeleton material.
