As production Steel wire/transparent tube As an important part of sand blasting machinery, its safety plays a vital role in the safety of equipment operation. The following will briefly analyze the precautions in the use of high-pressure sandblasting pipe: I. Pipe inner diameter: inner diameter of high-pressure sandblasting pipe. 2、 Attention shall be paid to the following items in the use and design of high-pressure sandblasting pipe: 1. The bending radius of high-pressure sandblasting pipe shall not be too small, and generally shall not be less than the value specified in the assembly technology of high-pressure sandblasting pipe. The joint between the high-pressure sandblasting pipe assembly and the pipe joint shall have a straight section, and its length shall not be less than twice the outer diameter of the pipe. 2. The length of high-pressure rubber hose assembly shall consider that the high-pressure rubber hose will shrink and deform after introducing pressure oil. Generally speaking, the shrinkage rate is 3~4 times of the pipe length. When installing the high-pressure rubber hose assembly, it is not allowed to bear tension. 3. During installation, the high-pressure sandblasting pipe assembly shall be free from torsional deformation. Steel wire/transparent tube company The connecting shaft of shall be placed in the moving plane as far as possible to avoid damaging the high-pressure sandblasting pipe when both ends move with each other. 4. High pressure resistant sand blasting pipe shall avoid contact and friction with mechanical sharp corners to avoid damaging the pipe. Safety measures: to ensure the safe and reliable use of high-pressure sandblasting pipe assembly.

Yangzhou Steel wire/transparent tube The break of the sandblasting hose usually refers to the appearance and change of the crack of the sandblasting hose. The sandblasting hose has one or more cracks, but the cracks are neat. Another is that the internal bending cracks at the crack of the sandblasting hose are neat. The causes of different errors are different, and the treatment methods are also different. Therefore, in the process of using or protecting the sandblasting hose, the sandblasting hose should not be subject to changing torque. When installing the sandblasting hose, try to keep the axis of the two joints on the same plane to avoid twisting the sandblasting hose in use. Therefore, be careful with the application, and try not to make the sandblasting hose change excessively to avoid consumption. Sand blasting hose plays a very important role in the industry. Its inner rubber layer is added with carbon black, which can effectively eliminate static electricity and directly contact with compressed air and abrasives. The requirement for wear resistance is quite high. Once worn through, the reinforcement layer will be exposed, and the sand blasting hose will burst. The reinforcing layer of sandblasting hose is a pressure resistant layer, so production Steel wire/transparent tube The material and layout of the reinforcement layer directly determine the pressure rating of the sandblasting hose. There are two common enhancement layers: cloth clip enhancement layer and surround enhancement layer. The sand blasting hose with an inner diameter of 50mm or more is mostly used in the construction occasions where the sand blasting pipe needs to be extended to reduce the pressure loss in the sand blasting hose and ensure the normal operation of shot blasting.

1. Mutual wear of rubber lining plate and steel ball of ball mill: both the rubber lining plate and steel ball of ball mill are vulnerable parts. During grinding, the steel ball and material of ball mill do throw line falling movement in the barrel Yangzhou Steel wire/transparent tube It will collide with steel balls and materials and cause friction. In continuous operation, the rubber lining plate and steel ball of ball mill will be severely worn, which is directly related to the hardness of materials. The greater the hardness of the material, the faster the abrasion speed of the rubber lining plate and steel ball of the ball mill, which may cause equipment damage or even safety accidents in serious cases. In addition, it is also related to the ball of the ball mill. The size and quantity of the ball will affect the service life of the rubber lining plate of the ball mill. If the ball mill is in operation, increasing the amount of steel balls or filling steel balls with larger diameters will increase the wear of the rubber lining plate of the ball mill. 2. The heat treatment process of the rubber lining plate of the ball mill is unreasonable: the unreasonable heat treatment of the rubber lining plate of the ball mill will not only increase the wear of the lining plate, but also affect the yield strength of the lining plate, resulting in the fracture of the bolt of the ball mill under the large shear force. In the actual operation, the staff lacked the understanding of the lining plate material and the heat treatment processing of the ball mill rubber lining plate was insufficient, so the strengthening effect of the ball mill rubber lining plate was not in place and the strength was low. When impacted by steel balls and materials, Steel wire/transparent tube company Plastic deformation often occurs. 3. The material of the rubber lining plate of the ball mill is unreasonable: the material of the rubber lining plate of the ball mill and its heat treatment process are the key to determine the mechanical performance of the lining plate. If the material of the lining plate is not properly selected, its fatigue strength and life will be greatly reduced, which will not meet the requirements of the ball mill, or even plastic deformation or bulge will occur.

production Steel wire/transparent tube It will burst for a long time due to frequent and severe pressure shocks. This situation is usually not caused by excessive static pressure, but is related to the strength and frequency of pressure shock. During the operation of construction machinery, the oil pressure in the oil resistant hose will rise or fall repeatedly, and then it will form frequent pressure shocks to the oil pipe, causing the oil seal of each part to become more damaged, the oil resistant hose will bubble and break, and the pipe joint will become loose and leak. Therefore, in the process of operation, the valve rod should not be pulled too hard, and it needs to be gentle. The application temperature of the oil in the oil resistant rubber hose is too high, resulting in aging and bursting of the rubber hose. During the operation of construction machinery, the hydraulic system will cause the oil to become hot due to power failure, and the influence of external temperature (especially in summer) will cause the oil temperature to rise sharply. The higher the oiling temperature is, the easier the rubber hose ages, the worse the elasticity is, the lower the strength and sealing function are, and the oil resistant hose will burst quickly. Therefore, Steel wire/transparent tube company During operation, when the temperature rise of the hydraulic system is too high or too fast, the causes should be found and eliminated in time. Necessary cooling measures shall be taken for summer operation, especially continuous operation.

We are all denominators. Why treat ourselves as molecules. But I think we Steel wire/transparent tube company The mass of is absolutely the molecule in the same industry. From raw materials, the general manager is responsible for the purchase of raw materials. Raw materials can only enter the factory after passing the inspection. Because it is the boss's own purchase and inspection, there is no buyer to take kickback, which increases the cost of raw materials and reduces the quality of raw materials. Speaking of the manufacturer's production process, it is difficult to find the second advanced mixer equipment among the new sand pumping hose manufacturers in 2019. It ensures that our glue is more uniform. This ensures the quality of our sand pumping hose. About 70% of sand pumping hose is manual work, and the production technology experience of workshop workers largely determines the quality of our sand pumping hose. 70% of our workshop workers have more than 7 years of production production Steel wire/transparent tube Experience. Select rubber hose Wang Xueyan purchases sand pumping rubber hose, which is more insurance than insurance company. Our goal is to become a member of the hose industry with excellent sand pumping hose quality. Place an order yesterday and deliver it today. At this speed, it is hard to find a second sand pumping hose in the industry. Life doesn't treat us kindly because we are women. But we should treat our own lives well and try to sell sand pumping hoses. As an excellent salesman, will you also receive an inquiry like chicken ribs. When I was just doing business, I received a 3 page quotation, and I patiently sorted it out for about 2 days. Finally, there was no news. Now I have been doing business for more than 10 years. Sometimes I can accurately judge the order rate of this order simply by looking at the inquiry list. The real heart of the words lies in the customers who make good deals.