Xi'an Braided hose The structure is composed of liquid resistant synthetic rubber inner rubber layer, medium rubber layer, I or II or III steel wire braid reinforcement layer, and weather resistant synthetic rubber outer rubber layer. Sand pumping hose features: 1. Sand pumping hose is made of special synthetic rubber, which has excellent oil resistance, heat resistance and aging resistance. 2. The rubber hose has high bearing pressure and excellent pulse performance. 3. The pipe body is tightly combined, soft to use, and has little deformation under pressure. 4. Sand pumping hose has excellent bending resistance and fatigue resistance. 5. The sand pumping hose is long, φ 20 meters above 32, φ Below 25 meters, it can reach 10 meters or even 100 meters. Sand pumping hose parameters: 1. The inner wall of nylon cord hose is smooth with little friction. Reinforcing layer: high-strength synthetic wire, spiral winding of steel wire and iron wire (sand suction pipe) 2 wear-resisting Braided hose Flange connection (ANSI150 standard flange) 3. Nominal pressure: 20BAR4, temperature: - 50 ℃ -+95 ℃ 5. Working pressure of sand suction hose and mud discharge pipe: positive pressure: 10kg; Test pressure: working negative pressure of 15kg steel ring sand suction hose: ≥ 15kg sand suction hose has strong flexibility, which is mainly used as the sand pump sand discharge pipe to connect the sand transport pipe and sand pump, as well as the pipe connection bend.

Although fire Xi'an Braided hose Explosion proof pipe) can be compressed and stretched, but if the installation position is incorrect, it will break quickly and reduce the service life. The sandblasting hose can be installed horizontally, vertically or obliquely. The most ideal condition is vertical installation. At the same time, avoid installing near the wheel, and install baffle if necessary. Generally speaking, the flame spraying metal sand blasting hose (explosion-proof pipe) can be divided into three lengths: the first is the compression length, that is, the length of the sand blasting hose when it is compressed to the limit position; The second is the installation length, that is, the length of the sandblasting hose when it is in the middle of half of the maximum displacement. The third type is the stretching length, that is, the length when the sandblasting hose is stretched to the maximum limit. When installing the sandblasting hose, the sandblasting hose should be in the middle position, which is called the installation length. When installed at this position, the sandblasting hose can move in two directions when bearing axial load. Otherwise, if it can only move in one direction, its strength will be affected and its service life will be reduced. In the actual installation process, considering that measuring the length of the sandblasting hose with a ruler according to the calculation results may affect the production efficiency, some foreign manufacturers directly install the ruler on the sandblasting hose, and cut the ruler after installation. From the structural point of view, the metal flame spraying metal sandblasting hose (explosion-proof pipe) is composed of strip and tube parts, which can form annular flame spraying metal sandblasting hose bellows and spiral flame spraying metal sandblasting hose bellows. Braided hose Where can I find it? Just because the corrugated pipe of the fire sprinkler metal sandblasting hose formed by this article always has a certain length of brazing or welding buckles and fire sprinkler metal sandblasting hose joints, the residues of the working medium often accumulate in these places, and the cleaning test and mechanical impurities in the working medium will deposit down to pollute the inner cavity. Therefore, its use reliability is relatively poor.

Xi'an Braided hose It is used for transportation, construction and other operating equipment. Incorrect operation and incorrect environment may affect the normal use of steel braided sandblasting pipe. What specific factors will affect the normal use of steel braided sand blasting pipe? The quality will definitely affect the use effect. The poor quality is actually related to the selected raw materials. Some raw materials are of high quality, and the quality of steel braided sandblasting pipes produced is also very good. However, if the steel braided sand blasting pipe is made of inferior plastic, the quality is very poor, which also affects the use effect. The use environment affects the use effect. Anti static steel braided sand blasting pipe is usually used in industry. Because these products are very common, the demand is also large. However, people do not pay attention to the use environment. If used in strong acid and alkali environment, steel braided sand blasting pipe will naturally corrode. Or if used in a relatively high temperature area, the steel braided sandblasting pipe may melt. Anti static steel braided sand blasting pipe will also affect the use effect. In the eyes of most users, the greater the degree, the better the nature. So if you choose a good one, users can use it with confidence. Understanding and avoiding the wrong use of high-pressure pipeline can reduce the possibility of high-pressure pipeline failure. The following brief introduction will help you. 1. Frequent and serious pressure shock: high-pressure pipeline burst is generally not caused by excessive static pressure, but is related to the severity and frequency of pressure shock. During the operation of construction machinery, the sudden increase or decrease of oil pressure in the high-pressure pipe will occur repeatedly, which will cause frequent pressure shocks to the oil pipe, leading to the aggravation of oil seal damage at various parts, blistering and cracking of rubber hose, and loosening and leakage of pipe joints. Therefore, during operation, the valve rod shall not be pulled too hard, but must be pulled gently. 2. The use temperature of oil is too high: during the operation of construction machinery, due to the power loss of the hydraulic system, the oil will rise, and the external temperature (especially in summer) will lead to a sharp rise in the oil temperature. wear-resisting Braided hose Where can I find it? The higher the oil temperature is, the easier the rubber is to age, the worse the elasticity is, the lower the strength and sealing performance are, and the high-pressure pipe will burst rapidly. Therefore, when the temperature rise of the hydraulic system is too high or too fast during operation, the causes should be found out and eliminated in time. For summer operation, especially continuous operation, necessary cooling measures shall be taken.

Braided hose Where can I find it? The following recommendations contain a series of precautions to prevent items from aging to a greater extent during storage. 1. During storage, the rotating plan system shall be adopted to shorten the storage time of high-pressure braided hose as much as possible. If long-term storage cannot be avoided and the following recommendations cannot be followed, high-pressure braided hoses should be thoroughly inspected before use. 2. Physical storage conditions: The high-pressure braided hose must be stored without mechanical pressure, including excessive stretching, compression or deformation, and without contact with sharp or sharp objects. High pressure braided hoses should be stored on suitable supports or on dry ground. High pressure braided rubber tubes packaged as coils must be stored horizontally. High pressure braided rubber pipes shall not be stacked. If stacking cannot be avoided, the stacking height shall not cause permanent deformation of the high-pressure braided rubber pipe below. Pumping high-pressure hydraulic hose is a common high-pressure hydraulic hose. In order to ensure the operation safety of the pumped high-pressure hydraulic hose, the following small series will briefly introduce the correct use of the pumped high-pressure hydraulic hose: 1. Before each use of the high-pressure hydraulic hose, the surface of the high-pressure hydraulic hose must be evenly coated with soap liquid, which can play a non bonding role between the high-pressure hydraulic hose and the concrete, and play a lubricating role in the drawing process, It can greatly increase the reuse times of high-pressure hydraulic hoses. 2. Installation: first, insert the steel hinge wire into the inner hole of the draw tube to avoid extrusion deformation when pouring concrete. Then, pull out the high-pressure hydraulic hose coated with soap liquid from the prestressed hole and fix it in the correct position with a fixing ring. The spacing of the retaining rings is controlled by the suspension and is usually about 500 mm. wear-resisting Braided hose When connecting the high-pressure hydraulic hose, wrap both ends of the high-pressure hydraulic hose for one and a half weeks or two weeks with thin iron sheet or PVC pipe (vertical cutting), fix them with iron wire, and then seal both ends of the PVC pipe with tape to avoid entering the mortar.