Whether in the process of purchase or use, high quality Rubber hose The quality of all needs to be checked regularly. During the inspection, the following items should be noted. 1. Standard size and actual error of high-pressure rubber hose: because the inner diameter and outer diameter of high-pressure sand blasting pipe and the outer diameter of the skeleton layer will shake, if the shaking amplitude exceeds the allowable limit, the balance of the buckling amount of the sand blasting pipe joint cannot be guaranteed, and the quality of the sand blasting pipe assembly cannot be guaranteed. Therefore, for the sand blasting pipe selected for the production of sand blasting pipe assembly, it is necessary to strictly check whether the inner diameter and outer diameter of the skeleton layer meet the requirements, and the requirements for the outer diameter error can be appropriately relaxed. 2. Wall thickness error of high-pressure hose: due to the local pain of the rubber layer in the high-pressure sandblasting pipe and the influence of the overlapping width of the rubber layer of the high-pressure sandblasting pipe quality inspection center between the skeleton layers, the wall thickness error of the sandblasting pipe may be too large. If the wall thickness error exceeds the allowable range, it will affect the tightness and pull-out strength of the connector, and even cause some deflection (tilting head) of the hose assembly connector. Quality inspection of high-pressure sand blasting pipe Therefore, the wall thickness error of sand blasting pipe should be strictly controlled. Generally, the rubber hose with wall thickness error exceeding 0.5mm shall be selected stably. 3. Adhesion between each layer of high-pressure rubber hose: high-quality high-pressure sand blasting pipe shall have prominent integrity, that is, the quality inspection of high-pressure sand blasting pipe shall have high adhesion between each structural layer, and the adhesion between each adhesive layer shall become an integrity. Only in this way can we meet various technical requirements in the process of joint installation and fastening, and only in this way can we ensure the quality inspection requirements of high-pressure sand blasting pipes for sand blasting pipe assembly. Therefore, Rubber hose Where can I find it? It is necessary to control the adhesive force between each layer of the rubber hose not lower than that specified in the technical standard, and the rubber hose with high adhesive force shall be selected as far as possible to produce the rubber hose assembly.

high quality Rubber hose It is characterized by high pressure, fire resistance, heat insulation, beautiful pipe body, corrosion resistance, anti-static, high wear resistance, light weight, high and low temperature resistance, good low-temperature bending performance, and long service life. Use: oilfield well control operation, metal smelting, chemical industry, etc. High temperature environment with heat source or thermal radiation. Hydraulic control pipeline of BOP for oil exploration and drilling. High pressure flame-retardant sand blasting pipe is mainly used for hydraulic transmission, medium transmission or power transmission under high-pressure, flammable and high-temperature environment. This product has been widely used in petroleum, chemical, marine, metallurgical and other industries. Flame retardant and fire-resistant: structure: take high temperature and high pressure steel wire winding hose as the base, and the outer skin is covered with nano fire-resistant coating, stainless steel wire braid and flame retardant layer. Hydraulic pipes in high-temperature environment near open fire, such as metallurgical industry, steelmaking, blast furnace, open hearth furnace, etc. Main Uses Hydraulic transmission is widely used in petroleum, chemical, marine transportation media or power transmission under high-pressure, flammable and high-temperature environments. Our products flame retardant sand blasting pipes are characterized by high pressure resistance, fire resistance, heat insulation, oil resistance, acid and alkali resistance. Rubber hose Where can I find it? When used in oil drilling well control system, it is superior to ordinary hard pipes, safe and reliable, easy to install and disassemble, time-saving, labor-saving, corrosion resistant, maintenance free, and long service life. Fire resistance: it can work for 15 minutes at 750 ℃. Oil resistance: Immerse in hydraulic oil at 40 ℃ - 100 ℃ for 24 hours without deterioration or falling off.

Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Hangzhou Rubber hose It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Rubber hose Where can I find it? The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.

For the woodworking industry, many users high quality Rubber hose Not unfamiliar, this is an industrial dust collector used on woodworking carving machines, mainly used to absorb wood chips, wood ash, etc. At present, there are many kinds of woodworking vacuum tubes on the market. In the past few years, major furniture factories used PVC steel wire hoses with flat ends. In recent years, more and more enterprises have replaced cheap PVC steel wire hoses with more wear-resistant and durable pu steel wire expansion tubes. Some of the former take a few days or a month, while some of the latter take a few months or a year, They are also steel wire hoses. Why is the service life gap so far? First of all, you may have the impression that many PVC hoses have a very bad smell. This kind of hose is often used in daily life. Because the raw material itself is very cheap, the price of the finished product is also very low. For example, only a dozen yuan a piece. Think about the price of PVC raw materials, which is generally 8-15 yuan a kilogram, And most businesses will not use expensive PVC raw materials, Rubber hose Where can I find it? The woodworking vacuum tube produced in this way has a very strong smell, not only unpleasant, but also many times the product can not even achieve environmental protection. However, the current updated product, pu steel wire telescopic tube, is a large woodworking furniture factory. An expensive woodworking carving machine uses a cheap vacuum tube with a very smelly smell, which has much to do with the overall style.

high quality Rubber hose It will burst for a long time due to frequent and severe pressure shocks. This situation is usually not caused by excessive static pressure, but is related to the strength and frequency of pressure shock. During the operation of construction machinery, the oil pressure in the oil resistant hose will rise or fall repeatedly, and then it will form frequent pressure shocks to the oil pipe, causing the oil seal of each part to become more damaged, the oil resistant hose will bubble and break, and the pipe joint will become loose and leak. Therefore, in the process of operation, the valve rod should not be pulled too hard, and it needs to be gentle. The application temperature of the oil in the oil resistant rubber hose is too high, resulting in aging and bursting of the rubber hose. During the operation of construction machinery, the hydraulic system will cause the oil to become hot due to power failure, and the influence of external temperature (especially in summer) will cause the oil temperature to rise sharply. The higher the oiling temperature is, the easier the rubber hose ages, the worse the elasticity is, the lower the strength and sealing function are, and the oil resistant hose will burst quickly. Therefore, Rubber hose Where can I find it? During operation, when the temperature rise of the hydraulic system is too high or too fast, the causes should be found and eliminated in time. Necessary cooling measures shall be taken for summer operation, especially continuous operation.