Many people have never understood high quality Sandblasting pipe It is better to use cast iron or rubber lining plate, so today I will give you a detailed analysis. The lining plate of the ball mill can tell you for sure that it is better to use rubber lining plate, which is also a trend for rubber lining plate to replace manganese steel lining plate. The rubber lining plate has many advantages that can not be achieved by manganese steel lining plates such as cast iron, so it has more advantages. One of the advantages of using cast iron or rubber liner for ball mill liner is that the noise of rubber liner is lower. In the process of grinding the rubber lining plate with materials, the noise is lower because it is not directly rubbed. Moreover, the rubber lining plate can throw the steel ball up for the second time to form the second grinding of materials, which makes the grinding of materials more thorough and the grinding fineness more uniform with good effect. In addition, the rubber lining plate can reduce the noise by an average of 30 dB compared with the noise of the cast iron lining plate, making it acceptable. Another important reason is energy saving. Energy consumption is an unavoidable problem for users of ball mills, because the cast iron lining plate is heavy in quality, Sandblasting pipe company Therefore, when the motor drives the lining plate, it will consume a lot of power. The rubber used by the rubber lining plate itself is light, so the electric energy consumed by the motor when driving is very small, which can be more than 10000 yuan of electric energy a year.

Nanchang Sandblasting pipe The structure is composed of liquid resistant synthetic rubber inner rubber layer, medium rubber layer, I or II or III steel wire braid reinforcement layer, and weather resistant synthetic rubber outer rubber layer. Sand pumping hose features: 1. Sand pumping hose is made of special synthetic rubber, which has excellent oil resistance, heat resistance and aging resistance. 2. The rubber hose has high bearing pressure and excellent pulse performance. 3. The pipe body is tightly combined, soft to use, and has little deformation under pressure. 4. Sand pumping hose has excellent bending resistance and fatigue resistance. 5. The sand pumping hose is long, φ 20 meters above 32, φ Below 25 meters, it can reach 10 meters or even 100 meters. Sand pumping hose parameters: 1. The inner wall of nylon cord hose is smooth with little friction. Reinforcing layer: high-strength synthetic wire, spiral winding of steel wire and iron wire (sand suction pipe) 2 high quality Sandblasting pipe Flange connection (ANSI150 standard flange) 3. Nominal pressure: 20BAR4, temperature: - 50 ℃ -+95 ℃ 5. Working pressure of sand suction hose and mud discharge pipe: positive pressure: 10kg; Test pressure: working negative pressure of 15kg steel ring sand suction hose: ≥ 15kg sand suction hose has strong flexibility, which is mainly used as the sand pump sand discharge pipe to connect the sand transport pipe and sand pump, as well as the pipe connection bend.

Although fire Nanchang Sandblasting pipe Explosion proof pipe) can be compressed and stretched, but if the installation position is incorrect, it will break quickly and reduce the service life. The sandblasting hose can be installed horizontally, vertically or obliquely. The most ideal condition is vertical installation. At the same time, avoid installing near the wheel, and install baffle if necessary. Generally speaking, the flame spraying metal sand blasting hose (explosion-proof pipe) can be divided into three lengths: the first is the compression length, that is, the length of the sand blasting hose when it is compressed to the limit position; The second is the installation length, that is, the length of the sandblasting hose when it is in the middle of half of the maximum displacement. The third type is the stretching length, that is, the length when the sandblasting hose is stretched to the maximum limit. When installing the sandblasting hose, the sandblasting hose should be in the middle position, which is called the installation length. When installed at this position, the sandblasting hose can move in two directions when bearing axial load. Otherwise, if it can only move in one direction, its strength will be affected and its service life will be reduced. In the actual installation process, considering that measuring the length of the sandblasting hose with a ruler according to the calculation results may affect the production efficiency, some foreign manufacturers directly install the ruler on the sandblasting hose, and cut the ruler after installation. From the structural point of view, the metal flame spraying metal sandblasting hose (explosion-proof pipe) is composed of strip and tube parts, which can form annular flame spraying metal sandblasting hose bellows and spiral flame spraying metal sandblasting hose bellows. Sandblasting pipe company Just because the corrugated pipe of the fire sprinkler metal sandblasting hose formed by this article always has a certain length of brazing or welding buckles and fire sprinkler metal sandblasting hose joints, the residues of the working medium often accumulate in these places, and the cleaning test and mechanical impurities in the working medium will deposit down to pollute the inner cavity. Therefore, its use reliability is relatively poor.

Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Nanchang Sandblasting pipe It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Sandblasting pipe company The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.