Changsha wear-resisting In places that must be crossed or may rub with the mechanical surface when working, hose clamps or springs and other protective devices should be used to prevent the outer layer of the sandblasting hose from being damaged. Sand blasting hose shall be arranged to avoid heat source as far as possible and away from the performance of engine exhaust pipe. If necessary, sleeve or protective screen can be used to prevent the hose from being heated and deteriorated. When the sand blasting hose must be bent, the bending radius should not be too small, and should be greater than 9 times the outer diameter. There should be a straight line section greater than 2 times the outer diameter of the pipe at the joint between the rubber hose and the joint. How high-quality the products and equipment we use are, it is inevitable that there will be some large and small failures in the process of using them, which will more or less have a certain impact on our work. Just like the use of sandblasting hose, there are traces of its outer adhesive seam, problems must be solved, For this, we explained the following solutions: First, the used water cloth should be used according to the original elastic edge of the water cloth when it is reused. 2： When we wrap the water cloth around the seam of the sandblasting hose, we should apply sufficient and uniform pressure to the pipe body. 3. The water cloth with different widths should be selected according to the size of the outer diameter of the wrapped sandblasting hose (for hose with an outer diameter of less than 30mm, the width of the water cloth should not exceed 90mm). The overlapping width of the water cloth should be 3/5-2/3 of the width of the water cloth.

Changsha Sand suction hose 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Sand suction hose Where can I find it? When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.

Comprehensive evaluation of world conveyor belt wear-resisting Sand suction hose The development level and the application practice of large industrial and mining enterprises in China, in the future, the technology and market development of conveyor belt vulcanizers in China will show the following eight characteristics: more intelligent: Canada Xiaoai Group has recently launched a new X-PAD conveyor belt vulcanizer control system, which uses full touch color screen control, and one operating system can implement real-time monitoring on multiple pairs of vulcanizer heating plates, And it can conduct remote monitoring through WIFI. This system will greatly improve the intelligent control degree of conveyor belt vulcanizer, and undoubtedly represents an important trend in the future development of conveyor belt vulcanizer technology. Higher cost performance: With the improvement of refined management of industrial and mining enterprises, the extensive "stupid and bulky" equipment can no longer adapt to modern production, and the provision of "customized combination" system solutions will become an inevitable choice for future conveyor belt vulcanizer suppliers - conveyor belt vulcanizer is a "tool type" equipment, Suppliers or design units can assist industrial and mining enterprises to comprehensively analyze the belt width, lap length and other use conditions of the conveyor system, and customize the overall solution of the conveyor belt vulcanizer that can be applied to multiple belt joints and maintenance at the same time. So as to effectively reduce procurement costs. More security: in terms of security measures, Sand suction hose Where can I find it? As the leader in the conveyor belt vulcanizing machine industry, Xiao Ai segmented vulcanizing machine can be used as a model: (1) its beam system adopts aviation grade aluminum profile, zhuanliE design, and has a safety window. When it is used, it penetrates the safety bar, and is equipped with a safety pin protection system; (2) International certified cables such as American UL are used to fully ensure the safety and reliability of use. (3) The recently launched new UBR vulcanizing machine pioneered the use of new materials to replace the bolt structure with a strong rope system, and designed a related structure between the new beams, which used the safety protection measures of the vulcanizing machine pressurization system to the extreme.

Changsha Sand suction hose There are many specifications. Different installation positions require different specifications of cloth clamping sand blasting pipe, and the specification selection of cloth clamping sand blasting pipe has different requirements. The following small series will briefly introduce them to you: 1. Temperature: The selection should be based on the ambient temperature when the cloth clip sandblasting pipe is working. In case of high temperature, the temperature correction pressure shall be determined according to the working pressure and temperature correction coefficient of the cloth sanding pipe under high temperature to determine the correct pressure level. 2. Pressure: when selecting the cloth clip sandblasting pipe, check the nominal diameter and pressure gauge of the corrugated cloth clip sandblasting pipe according to the actual working pressure of the hose to determine whether to use the stainless steel mesh sleeve type. 3. Size: select the joint type, size of cloth sanding pipe and hose length according to the size of cloth sanding pipe. 4. Medium: determine the material of each part of the hose according to the chemical properties of the material medium transported in the cloth sanding pipe and the corrosion resistance of the hose material. 5. Status: According to the use status of the hose, refer to the correct use and installation method of the cloth clip sandblasting pipe and the length of the hose in the settlement compensation. Therefore, Sand suction hose Where can I find it? According to the actual pressure of the system, the higher the working pressure of the cloth clamping sand blasting pipe is, the normal operation of the system can be ensured, and the appropriate cloth clamping sand blasting pipe is selected.

Changsha Sand suction hose It is a kind of hose that can be used for sand pumping and sand suction produced with high abrasion resistant rubber. It is often used in sand blasting industry, cement, steel, minerals and other industries, but it is mainly used in river dredging, slurry transportation in mines, sand digging and sand taking and other industries to transport sharp granular solids or solid-liquid mixtures. Its product structure is composed of high wear-resistant layer, reinforced water pipe layer, skeleton steel wire and outer rubber. Today, Myers will introduce the application field of wear-resistant sand absorption rubber pipe. When the wear-resistant sand suction rubber pipe is applied in the mine pit, it is necessary to set a floating boat equipped with a sand pump in the mine pit, and use the floating sand suction rubber pipe to connect with the sand pump. The floating boat will float up and down with the rise and fall of the water level. It is required that the pipe body has good flexibility and good tear resistance and bending resistance. The offshore pipeline is connected by non floating sand suction hose until the pulp transportation destination. The overall pipeline is divided into two parts, one for surface use and the other for onshore use. The main raw material of these two kinds of hoses is high abrasion and corrosion resistant rubber, and cord reinforcement layer and steel wire skeleton layer are added in the pipe wall to ensure the pressure resistance and tear resistance of the hose. The connection mode is vulcanized flange connection, that is, the flange and the hose are a whole, so there is no need to worry about the flange falling off. Floating sand suction hose used on the water surface. This kind of hose is required to float on the water surface. Due to the large drop of the mine (100 meters) and the long conveying distance Sand suction hose Where can I find it? The hose shall have high pressure resistance, and the design pressure is 25 kg/cm2 according to the calculation. It should be considered that the floating ship will move up and down with the rise and fall of the water level and the wave will cause lateral displacement. Its internal structure is the same as the sand suction hose used offshore, except that a floating body is installed outside the hose.

If conditions permit, secondary vulcanization shall be adopted, wear-resisting Sand suction hose Effectively remove the odor generated during the consumption of odorless hose. Pay attention to the volatilization of various ingredients in the odorless hose formula. When the odorless hose is consumed, in addition to paying special attention to the raw materials and vulcanization process of the reclaimed rubber, pay attention to the selection of various ingredients and whether they will volatilize in the vulcanization process. The volatilization of vulcanizing agent, accelerator and antioxidant will produce a great smell. It is very important to accurately determine the length of the required rubber sand blasting pipe by using the rubber sand blasting pipe. It shall also be checked whether the use conditions of the rubber sand blasting pipe meet the requirements of the selected rubber sand blasting pipe. It should be ensured that the rubber sand blasting pipe you will use is the most suitable one. The working pressure and suction should be carefully determined. Special attention shall be paid to the test standard pressure change or pressure peak of wear-resistant sand blasting pipe. Exceeding the promised maximum value will greatly shorten the service life of the rubber sand blasting pipe. Both ends of the rubber sand blasting pipe cannot be continuously immersed in the transported material. If the bending radius of the rubber sand blasting pipe is less than the minimum value, Changsha Sand suction hose Its service life will be greatly shortened. Therefore, before installation, it is recommended that you consult the application of information, especially the information about the bending radius of the rubber sand blasting pipe. Protection and cleaning of rubber sand blasting hose: it is recommended to empty the hose after use. Clean if necessary. Inspection: After each use, the rubber sand blasting pipe must be inspected to ensure that it does not show structural damage.