Sandblasting pipe Price The following recommendations contain a series of precautions to prevent items from aging to a greater extent during storage. 1. During storage, the rotating plan system shall be adopted to shorten the storage time of high-pressure braided hose as much as possible. If long-term storage cannot be avoided and the following recommendations cannot be followed, high-pressure braided hoses should be thoroughly inspected before use. 2. Physical storage conditions: The high-pressure braided hose must be stored without mechanical pressure, including excessive stretching, compression or deformation, and without contact with sharp or sharp objects. High pressure braided hoses should be stored on suitable supports or on dry ground. High pressure braided rubber tubes packaged as coils must be stored horizontally. High pressure braided rubber pipes shall not be stacked. If stacking cannot be avoided, the stacking height shall not cause permanent deformation of the high-pressure braided rubber pipe below. Pumping high-pressure hydraulic hose is a common high-pressure hydraulic hose. In order to ensure the operation safety of the pumped high-pressure hydraulic hose, the following small series will briefly introduce the correct use of the pumped high-pressure hydraulic hose: 1. Before each use of the high-pressure hydraulic hose, the surface of the high-pressure hydraulic hose must be evenly coated with soap liquid, which can play a non bonding role between the high-pressure hydraulic hose and the concrete, and play a lubricating role in the drawing process, It can greatly increase the reuse times of high-pressure hydraulic hoses. 2. Installation: first, insert the steel hinge wire into the inner hole of the draw tube to avoid extrusion deformation when pouring concrete. Then, pull out the high-pressure hydraulic hose coated with soap liquid from the prestressed hole and fix it in the correct position with a fixing ring. The spacing of the retaining rings is controlled by the suspension and is usually about 500 mm. wear-resisting Sandblasting pipe When connecting the high-pressure hydraulic hose, wrap both ends of the high-pressure hydraulic hose for one and a half weeks or two weeks with thin iron sheet or PVC pipe (vertical cutting), fix them with iron wire, and then seal both ends of the PVC pipe with tape to avoid entering the mortar.
With the development of modern industry, the demand for high temperature and high pressure sandblasting hoses is growing, Sandblasting pipe Price Scope of application: completely flexible conveying pipe is required to prevent the pipe from being in vibration position. It is suitable for steam, gas, air, heavy oil, petroleum, chemical industry, etc. First of all, the structure of fire sprinkler metal sandblasting hose (explosion-proof pipe) must have compulsory knowledge. Fire sprinkler metal sandblasting hose (hereinafter referred to as explosion-proof pipe) is a high-quality sandblasting hose in modern industrial pipelines. It is mainly composed of fire sprinkler metal sandblasting hose bellows, fire sprinkler metal sandblasting hose net sleeve and fire sprinkler metal sandblasting hose connector. The inner pipe is a thin-walled stainless steel fire sprinkler metal sandblasting hose corrugated pipe with spiral or circular waveform. The outer layer of the fire sprinkler metal sandblasting hose corrugated pipe is woven by stainless steel wire or steel strip according to certain parameters. The fire spraying metal sand blasting hose connector or flange at both ends of the sand blasting hose shall match with the fire spraying metal sand blasting hose connector or flange of the user's pipeline. wear-resisting Sandblasting pipe Scope of application of fire sprinkler metal sandblasting hose (explosion-proof pipe): full flexible conveying pipe is required in vibration places to prevent pipes, which is applicable to steam, gas, air, heavy oil, petroleum, chemical industry, etc. The annular flame spraying metal sandblasting hose bellows is a special geometric pipe. The outer edges of several annular diaphragms are tangent to several concave half rings facing the center, and the inner edges are tangent to several concave half rings of the vest. Its blanks are mainly made of tubes. The fire sprinkler metal sandblasting hose bellows has the characteristics of large flexibility, good elasticity, simple manufacturing and small rigidity.
Hefei Sandblasting pipe It is used in transportation, construction and other industries. Correct procurement can not only save procurement costs, but also ensure its operation safety. The following series will introduce some purchase suggestions, hoping to help you. Suggestion 1. Determine the type of hose brand to be purchased according to the connection equipment and budget of sandblasting hose, such as high-tech equipment. Naturally, it is necessary to buy large brand sandblasting hose. However, if it is industrial and mining equipment with extremely fast scrapping speed, general quality is enough. Recommendation 2. The price of sand blasting hose with uniform quality grade is also different, especially for large-scale procurement, the price difference will be obvious, so it is necessary to have three quality grades to determine the final partner. Suggestion 3: Select appropriate channels. Sand blasting hoses are usually purchased in large quantities, which means that their turnover is relatively large. Therefore, reliable channels need to be selected to ensure the safety of their own loans. Sandblasting pipe Price The purchase of sand blasting hose components is also described in the model. High pressure hose assembly, pipe body specification (inner diameter, number of pressure layers, winding or braiding), joint type (national standard or Eaton), protective layer type, length and other parameters are the basic data for determining hose assembly.
Hefei Sandblasting pipe It is used for transportation, construction and other operating equipment. Incorrect operation and incorrect environment may affect the normal use of steel braided sandblasting pipe. What specific factors will affect the normal use of steel braided sand blasting pipe? The quality will definitely affect the use effect. The poor quality is actually related to the selected raw materials. Some raw materials are of high quality, and the quality of steel braided sandblasting pipes produced is also very good. However, if the steel braided sand blasting pipe is made of inferior plastic, the quality is very poor, which also affects the use effect. The use environment affects the use effect. Anti static steel braided sand blasting pipe is usually used in industry. Because these products are very common, the demand is also large. However, people do not pay attention to the use environment. If used in strong acid and alkali environment, steel braided sand blasting pipe will naturally corrode. Or if used in a relatively high temperature area, the steel braided sandblasting pipe may melt. Anti static steel braided sand blasting pipe will also affect the use effect. In the eyes of most users, the greater the degree, the better the nature. So if you choose a good one, users can use it with confidence. Understanding and avoiding the wrong use of high-pressure pipeline can reduce the possibility of high-pressure pipeline failure. The following brief introduction will help you. 1. Frequent and serious pressure shock: high-pressure pipeline burst is generally not caused by excessive static pressure, but is related to the severity and frequency of pressure shock. During the operation of construction machinery, the sudden increase or decrease of oil pressure in the high-pressure pipe will occur repeatedly, which will cause frequent pressure shocks to the oil pipe, leading to the aggravation of oil seal damage at various parts, blistering and cracking of rubber hose, and loosening and leakage of pipe joints. Therefore, during operation, the valve rod shall not be pulled too hard, but must be pulled gently. 2. The use temperature of oil is too high: during the operation of construction machinery, due to the power loss of the hydraulic system, the oil will rise, and the external temperature (especially in summer) will lead to a sharp rise in the oil temperature. wear-resisting Sandblasting pipe Price The higher the oil temperature is, the easier the rubber is to age, the worse the elasticity is, the lower the strength and sealing performance are, and the high-pressure pipe will burst rapidly. Therefore, when the temperature rise of the hydraulic system is too high or too fast during operation, the causes should be found out and eliminated in time. For summer operation, especially continuous operation, necessary cooling measures shall be taken.
Hefei Sandblasting pipe Structure type of product: sand blasting hose is mainly composed of liquid resistant inner rubber layer, middle rubber layer, 2 or 4 or 6 layers of steel wire winding reinforcement layer and outer rubber layer. The inner rubber layer has the function of bearing the pressure of the transmission medium and protecting the steel wire from erosion, the outer rubber layer protects the steel wire from damage, and the steel wire (0.3-2.0 steel wire) layer is the reinforced skeleton material. Application of sandblasting hose products: high-pressure sandblasting hose is mainly used for mining hydraulic support and oil field exploitation, and is suitable for engineering construction, lifting and transportation, metallurgical forging, mining equipment, ships, injection molding machinery, agricultural machinery, various machine tools, and mechanical and automatic hydraulic systems in various industrial sectors to transport petroleum base with a certain pressure (higher pressure) and temperature. (such as mineral oil, soluble oil, hydraulic oil, fuel oil, lubricating oil) and water-based liquid (such as emulsion, oil-water emulsion, water). And liquid transmission. The working withstand voltage can reach 70-100 MPa. The company's sand blasting hose standards refer to national standards/T10544-03, DIN 20023, and SaE100 R9-13. Sandblasting pipe Price Made of special synthetic rubber, it has excellent oil resistance, heat resistance and aging resistance. The rubber hose has high bearing pressure and superior pulse performance. The tube body is tightly combined, soft to use, and has little compression deformation. The hose has excellent bending resistance and fatigue resistance. The sandblasting hose is 20m long and can be made within 50m as required.
