Weihai Suction and discharge pipe 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Suction and discharge pipe Price When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.

I believe everyone is familiar with wear-resisting Suction and discharge pipe Relevant application knowledge of products. It is understood that at present, this product is mainly used for mining hydraulic support and oilfield development. It is applicable to engineering construction, lifting transportation, metallurgical forging, mining equipment, ships, injection molding machinery, agricultural machinery, various machine tools, mechanization of various industrial departments, water-based liquids, etc. And liquid transmission. Its relatively high working pressure can reach 70-120 MPa. In order to achieve better application effect, what problems should be paid attention to when using high-pressure braided hose? 1. The bending radius shall not be less than the given bending radius to prevent damage to the hose skeleton or premature failure due to excessive tension. 2. Select the type and specification of the hose correctly according to the use conditions, and do not misuse or replace it. 3. When using high-pressure braided hose, the pressure should be adjusted slowly and evenly to avoid sudden pressure increase and damage to the pipe body. 4. When the work site changes, it should be removed from the ground without dragging, so as to avoid the skeleton layer being corroded after scratching the outer glue. 5. After delivering corrosive liquid, the interior should be cleaned to prevent residues from corroding the pipe body for a long time, or select corresponding series of products. When storing high-pressure braided rubber hoses, depending on the type of rubber used, Suction and discharge pipe Price Note which conditions typically change over time. However, due to several factors or a combination of several factors, this change may accelerate, and other materials used to strengthen high-pressure braided hoses may also be adversely affected by improper storage conditions.

Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Weihai Suction and discharge pipe It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Suction and discharge pipe Price The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.

wear-resisting Suction and discharge pipe It will burst for a long time due to frequent and severe pressure shocks. This situation is usually not caused by excessive static pressure, but is related to the strength and frequency of pressure shock. During the operation of construction machinery, the oil pressure in the oil resistant hose will rise or fall repeatedly, and then it will form frequent pressure shocks to the oil pipe, causing the oil seal of each part to become more damaged, the oil resistant hose will bubble and break, and the pipe joint will become loose and leak. Therefore, in the process of operation, the valve rod should not be pulled too hard, and it needs to be gentle. The application temperature of the oil in the oil resistant rubber hose is too high, resulting in aging and bursting of the rubber hose. During the operation of construction machinery, the hydraulic system will cause the oil to become hot due to power failure, and the influence of external temperature (especially in summer) will cause the oil temperature to rise sharply. The higher the oiling temperature is, the easier the rubber hose ages, the worse the elasticity is, the lower the strength and sealing function are, and the oil resistant hose will burst quickly. Therefore, Suction and discharge pipe Price During operation, when the temperature rise of the hydraulic system is too high or too fast, the causes should be found and eliminated in time. Necessary cooling measures shall be taken for summer operation, especially continuous operation.

With the development of modern industry, the demand for high temperature and high pressure sandblasting hoses is growing, Suction and discharge pipe Price Scope of application: completely flexible conveying pipe is required to prevent the pipe from being in vibration position. It is suitable for steam, gas, air, heavy oil, petroleum, chemical industry, etc. First of all, the structure of fire sprinkler metal sandblasting hose (explosion-proof pipe) must have compulsory knowledge. Fire sprinkler metal sandblasting hose (hereinafter referred to as explosion-proof pipe) is a high-quality sandblasting hose in modern industrial pipelines. It is mainly composed of fire sprinkler metal sandblasting hose bellows, fire sprinkler metal sandblasting hose net sleeve and fire sprinkler metal sandblasting hose connector. The inner pipe is a thin-walled stainless steel fire sprinkler metal sandblasting hose corrugated pipe with spiral or circular waveform. The outer layer of the fire sprinkler metal sandblasting hose corrugated pipe is woven by stainless steel wire or steel strip according to certain parameters. The fire spraying metal sand blasting hose connector or flange at both ends of the sand blasting hose shall match with the fire spraying metal sand blasting hose connector or flange of the user's pipeline. wear-resisting Suction and discharge pipe Scope of application of fire sprinkler metal sandblasting hose (explosion-proof pipe): full flexible conveying pipe is required in vibration places to prevent pipes, which is applicable to steam, gas, air, heavy oil, petroleum, chemical industry, etc. The annular flame spraying metal sandblasting hose bellows is a special geometric pipe. The outer edges of several annular diaphragms are tangent to several concave half rings facing the center, and the inner edges are tangent to several concave half rings of the vest. Its blanks are mainly made of tubes. The fire sprinkler metal sandblasting hose bellows has the characteristics of large flexibility, good elasticity, simple manufacturing and small rigidity.

Weihai Suction and discharge pipe Structure type of product: sand blasting hose is mainly composed of liquid resistant inner rubber layer, middle rubber layer, 2 or 4 or 6 layers of steel wire winding reinforcement layer and outer rubber layer. The inner rubber layer has the function of bearing the pressure of the transmission medium and protecting the steel wire from erosion, the outer rubber layer protects the steel wire from damage, and the steel wire (0.3-2.0 steel wire) layer is the reinforced skeleton material. Application of sandblasting hose products: high-pressure sandblasting hose is mainly used for mining hydraulic support and oil field exploitation, and is suitable for engineering construction, lifting and transportation, metallurgical forging, mining equipment, ships, injection molding machinery, agricultural machinery, various machine tools, and mechanical and automatic hydraulic systems in various industrial sectors to transport petroleum base with a certain pressure (higher pressure) and temperature. (such as mineral oil, soluble oil, hydraulic oil, fuel oil, lubricating oil) and water-based liquid (such as emulsion, oil-water emulsion, water). And liquid transmission. The working withstand voltage can reach 70-100 MPa. The company's sand blasting hose standards refer to national standards/T10544-03, DIN 20023, and SaE100 R9-13. Suction and discharge pipe Price Made of special synthetic rubber, it has excellent oil resistance, heat resistance and aging resistance. The rubber hose has high bearing pressure and superior pulse performance. The tube body is tightly combined, soft to use, and has little compression deformation. The hose has excellent bending resistance and fatigue resistance. The sandblasting hose is 20m long and can be made within 50m as required.