Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Wuxi Corbel tube It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Corbel tube company The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.

Wuxi Corbel tube The structure is composed of liquid resistant synthetic rubber inner rubber layer, medium rubber layer, I or II or III steel wire braid reinforcement layer, and weather resistant synthetic rubber outer rubber layer. Sand pumping hose features: 1. Sand pumping hose is made of special synthetic rubber, which has excellent oil resistance, heat resistance and aging resistance. 2. The rubber hose has high bearing pressure and excellent pulse performance. 3. The pipe body is tightly combined, soft to use, and has little deformation under pressure. 4. Sand pumping hose has excellent bending resistance and fatigue resistance. 5. The sand pumping hose is long, φ 20 meters above 32, φ Below 25 meters, it can reach 10 meters or even 100 meters. Sand pumping hose parameters: 1. The inner wall of nylon cord hose is smooth with little friction. Reinforcing layer: high-strength synthetic wire, spiral winding of steel wire and iron wire (sand suction pipe) 2 production Corbel tube Flange connection (ANSI150 standard flange) 3. Nominal pressure: 20BAR4, temperature: - 50 ℃ -+95 ℃ 5. Working pressure of sand suction hose and mud discharge pipe: positive pressure: 10kg; Test pressure: working negative pressure of 15kg steel ring sand suction hose: ≥ 15kg sand suction hose has strong flexibility, which is mainly used as the sand pump sand discharge pipe to connect the sand transport pipe and sand pump, as well as the pipe connection bend.

Corbel tube company The following recommendations contain a series of precautions to prevent items from aging to a greater extent during storage. 1. During storage, the rotating plan system shall be adopted to shorten the storage time of high-pressure braided hose as much as possible. If long-term storage cannot be avoided and the following recommendations cannot be followed, high-pressure braided hoses should be thoroughly inspected before use. 2. Physical storage conditions: The high-pressure braided hose must be stored without mechanical pressure, including excessive stretching, compression or deformation, and without contact with sharp or sharp objects. High pressure braided hoses should be stored on suitable supports or on dry ground. High pressure braided rubber tubes packaged as coils must be stored horizontally. High pressure braided rubber pipes shall not be stacked. If stacking cannot be avoided, the stacking height shall not cause permanent deformation of the high-pressure braided rubber pipe below. Pumping high-pressure hydraulic hose is a common high-pressure hydraulic hose. In order to ensure the operation safety of the pumped high-pressure hydraulic hose, the following small series will briefly introduce the correct use of the pumped high-pressure hydraulic hose: 1. Before each use of the high-pressure hydraulic hose, the surface of the high-pressure hydraulic hose must be evenly coated with soap liquid, which can play a non bonding role between the high-pressure hydraulic hose and the concrete, and play a lubricating role in the drawing process, It can greatly increase the reuse times of high-pressure hydraulic hoses. 2. Installation: first, insert the steel hinge wire into the inner hole of the draw tube to avoid extrusion deformation when pouring concrete. Then, pull out the high-pressure hydraulic hose coated with soap liquid from the prestressed hole and fix it in the correct position with a fixing ring. The spacing of the retaining rings is controlled by the suspension and is usually about 500 mm. production Corbel tube When connecting the high-pressure hydraulic hose, wrap both ends of the high-pressure hydraulic hose for one and a half weeks or two weeks with thin iron sheet or PVC pipe (vertical cutting), fix them with iron wire, and then seal both ends of the PVC pipe with tape to avoid entering the mortar.

1. Mutual wear of rubber lining plate and steel ball of ball mill: both the rubber lining plate and steel ball of ball mill are vulnerable parts. During grinding, the steel ball and material of ball mill do throw line falling movement in the barrel Wuxi Corbel tube It will collide with steel balls and materials and cause friction. In continuous operation, the rubber lining plate and steel ball of ball mill will be severely worn, which is directly related to the hardness of materials. The greater the hardness of the material, the faster the abrasion speed of the rubber lining plate and steel ball of the ball mill, which may cause equipment damage or even safety accidents in serious cases. In addition, it is also related to the ball of the ball mill. The size and quantity of the ball will affect the service life of the rubber lining plate of the ball mill. If the ball mill is in operation, increasing the amount of steel balls or filling steel balls with larger diameters will increase the wear of the rubber lining plate of the ball mill. 2. The heat treatment process of the rubber lining plate of the ball mill is unreasonable: the unreasonable heat treatment of the rubber lining plate of the ball mill will not only increase the wear of the lining plate, but also affect the yield strength of the lining plate, resulting in the fracture of the bolt of the ball mill under the large shear force. In the actual operation, the staff lacked the understanding of the lining plate material and the heat treatment processing of the ball mill rubber lining plate was insufficient, so the strengthening effect of the ball mill rubber lining plate was not in place and the strength was low. When impacted by steel balls and materials, Corbel tube company Plastic deformation often occurs. 3. The material of the rubber lining plate of the ball mill is unreasonable: the material of the rubber lining plate of the ball mill and its heat treatment process are the key to determine the mechanical performance of the lining plate. If the material of the lining plate is not properly selected, its fatigue strength and life will be greatly reduced, which will not meet the requirements of the ball mill, or even plastic deformation or bulge will occur.