Whether in the process of purchase or use, production Rubber hose The quality of all needs to be checked regularly. During the inspection, the following items should be noted. 1. Standard size and actual error of high-pressure rubber hose: because the inner diameter and outer diameter of high-pressure sand blasting pipe and the outer diameter of the skeleton layer will shake, if the shaking amplitude exceeds the allowable limit, the balance of the buckling amount of the sand blasting pipe joint cannot be guaranteed, and the quality of the sand blasting pipe assembly cannot be guaranteed. Therefore, for the sand blasting pipe selected for the production of sand blasting pipe assembly, it is necessary to strictly check whether the inner diameter and outer diameter of the skeleton layer meet the requirements, and the requirements for the outer diameter error can be appropriately relaxed. 2. Wall thickness error of high-pressure hose: due to the local pain of the rubber layer in the high-pressure sandblasting pipe and the influence of the overlapping width of the rubber layer of the high-pressure sandblasting pipe quality inspection center between the skeleton layers, the wall thickness error of the sandblasting pipe may be too large. If the wall thickness error exceeds the allowable range, it will affect the tightness and pull-out strength of the connector, and even cause some deflection (tilting head) of the hose assembly connector. Quality inspection of high-pressure sand blasting pipe Therefore, the wall thickness error of sand blasting pipe should be strictly controlled. Generally, the rubber hose with wall thickness error exceeding 0.5mm shall be selected stably. 3. Adhesion between each layer of high-pressure rubber hose: high-quality high-pressure sand blasting pipe shall have prominent integrity, that is, the quality inspection of high-pressure sand blasting pipe shall have high adhesion between each structural layer, and the adhesion between each adhesive layer shall become an integrity. Only in this way can we meet various technical requirements in the process of joint installation and fastening, and only in this way can we ensure the quality inspection requirements of high-pressure sand blasting pipes for sand blasting pipe assembly. Therefore, Rubber hose Where can I find it? It is necessary to control the adhesive force between each layer of the rubber hose not lower than that specified in the technical standard, and the rubber hose with high adhesive force shall be selected as far as possible to produce the rubber hose assembly.
In the shipbuilding industry, radio industry, electrical industry, telecommunications industry, instrument industry, aviation industry, medical industry, etc., we often see acid and alkali resistant hose, then what is Chengdu Rubber hose What about? If you want to know more, please read down! Acid and alkali resistant silicone hose is a kind of pipe specially used for power equipment, which uses acid and alkali resistant silica gel as the main raw material and tightly wraps the pipe wall with electrical grade polyethylene spiral wire. Due to the chemical inertia of acid and alkali resistant silica gel, this kind of pipe has good acid and alkali resistance performance and electrical performance, and is commonly used in the production of wires, cables and lead wires in extreme acid and alkali environments. Also called: acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose. Features: 1. High temperature resistance (250-300 ℃) and low temperature resistance (- 40-60 ℃); 2. Good acid and alkali resistance. Physiologically stable, able to withstand repeated harsh and disinfection conditions, resistant to ozone aging, light aging, weather aging and ultraviolet radiation. 3. Small resilience and permanent deformation (no more than 50% at 200 ℃ for 48 hours), breakdown voltage (20-25KV/mm), ozone resistance and UV resistance. Rubber hose Where can I find it? Radiation resistance and other characteristics, 4. Good electrical performance, small change when exposed to moisture, water or temperature rise, even if the silica generated by short circuit combustion is still an insulator, which ensures that electrical equipment continues to work, so it is most suitable for making wires, cables and lead wires.
Chengdu Rubber hose It is mainly used for the transportation of liquid and gas. The use requirements of cloth clip sand blasting pipe are stricter than those of ordinary rubber hose. The so-called high voltage puts forward this requirement. The following small series will introduce the use requirements of cloth clip sandblasting pipe. According to the use characteristics of cloth clip sand blasting pipe, the larger working pressure of cloth clip sand blasting pipe is determined according to the system pressure. Each cloth clamping sand blasting pipe has a normal working pressure, and the bursting pressure of cloth clamping sand blasting pipe is 3-4 times of the larger working pressure. The higher the pressure, the higher the number of steel wire layers, and the more stringent the product production. Therefore, according to the actual pressure of the system, the higher the working pressure of the cloth clamping sand blasting pipe, the normal operation of the system can be ensured, and the appropriate cloth clamping sand blasting pipe can be selected. If the impact pressure of the system is frequent, the cloth clip sandblasting pipe with high pulse life shall be selected, and the specification and model classification of the cloth clip sandblasting pipe shall be properly improved. Temperature is also one of the factors considered by customers. Rubber hose Where can I find it? The high and low temperature transition in the working environment will affect the service life and pressure bearing capacity of the rubber hose. Therefore, high-pressure rubber hoses should be used within their allowable range. For the system whose long-term operating temperature is not within its allowable range, hose sheath or special rubber hose shall be purchased.
The hard core method adopts the core extrusion process to extrude the inner rubber tube blank, which directly uses the extruder to cover the inner rubber tube blank on the iron core, instead of the traditional casing process, and simplifies the process flow. Chengdu Rubber hose The billet forming adopts the process method of intertwining outer film and steel wire braiding forming. Similar to wrapping water wrapped cloth, the overlapping width is 1/2 of the film width. This process method can replace the method of wrapping outer film by extruder or by hand, reducing energy consumption and cost. We all know that the reinforcing layer and reinforcing layer of the rubber hose are the main force bearing parts, which are used to bear the load pressure. The factors determining the stress condition of the reinforced layer of the rubber hose are determined by the tension of the braided steel wire and the braiding angle. The high-speed steel wire hose braiding machine developed by our factory has introduced the advanced technology of foreign braiding production lines, and integrated the characteristics of domestic braiding machines. It integrates the advanced functions of hydraulic brake hose braiding production line, such as horizontal mechanical transmission, automatic lubrication, and so on, to develop equipment with high productivity and high degree of automation. The range of braiding diameter can be achieved Ф 6— Ф 25 Long core rubber hose (reinforcement layer). It fills the gap of domestic knitting production equipment, which can be widely used in rubber and plastic hose, rubber hose (reinforcement layer) knitting production equipment. The structure of high-pressure rubber hose is composed of four parts: inner liner, inner rubber layer, skeleton layer, middle rubber layer and outer rubber layer. Rubber hose Where can I find it? In case of direct contact with the conveying medium, the synthetic rubber with good medium resistance, high tensile strength, high constant tensile stress, small compression permanent deformation and easy processing is usually selected. In order to meet the use requirements of strong polar medium resistance, the inner liner is composed of polytetrafluoroethylene layer and rubber layer, and a layer of film or adhesive is added on the surface of the inner liner to improve the adhesion with the skeleton material.
production Rubber hose Or PVC steel wire spiral reinforced pipe. The commodity is made of high-quality PVC plastic raw materials. PVC steel wire reinforced pipe is also a PVC steel wire reinforced hose that uses steel wire reinforcement. The embedded spiral steel wire is used as the reinforcement layer, so the product has both rigidity and flexibility, that is, it has both satisfying mechanical properties and rigidity, and excellent flexibility. The reinforced pipe of latex fiber is PVC hose embedded with steel wire framework. The inner and outer tube walls are clear, lubricated, free of bubbles, and the fluid transportation is clearly visible. Silicone fiber tube is resistant to low concentration of acid and alkali, high elasticity, not easy to age, and has a long service life. Resistant to high pressure and can be kept intact under high pressure and vacuum. PVC steel wire pipe is made of new PVC reinforced materials, and has made great progress in compressive strength and hardness. The main production method of silica gel steel wire pipe is multiple production method. The main types of steel wire pipe in shopping malls include high pressure steel wire pipe, low pressure steel wire pipe, steel wire skeleton pipe and Tongming steel wire pipe. The application methods are different in different environments. The new PVC steel wire pipe is the most widely used commodity today. Rubber hose Where can I find it? After use, it will not be the same as the metal pipe, which is easy to deform and leak. What advantages does the PVC fiber reinforced pipe have.
production Rubber hose It is characterized by high pressure, fire resistance, heat insulation, beautiful pipe body, corrosion resistance, anti-static, high wear resistance, light weight, high and low temperature resistance, good low-temperature bending performance, and long service life. Use: oilfield well control operation, metal smelting, chemical industry, etc. High temperature environment with heat source or thermal radiation. Hydraulic control pipeline of BOP for oil exploration and drilling. High pressure flame-retardant sand blasting pipe is mainly used for hydraulic transmission, medium transmission or power transmission under high-pressure, flammable and high-temperature environment. This product has been widely used in petroleum, chemical, marine, metallurgical and other industries. Flame retardant and fire-resistant: structure: take high temperature and high pressure steel wire winding hose as the base, and the outer skin is covered with nano fire-resistant coating, stainless steel wire braid and flame retardant layer. Hydraulic pipes in high-temperature environment near open fire, such as metallurgical industry, steelmaking, blast furnace, open hearth furnace, etc. Main Uses Hydraulic transmission is widely used in petroleum, chemical, marine transportation media or power transmission under high-pressure, flammable and high-temperature environments. Our products flame retardant sand blasting pipes are characterized by high pressure resistance, fire resistance, heat insulation, oil resistance, acid and alkali resistance. Rubber hose Where can I find it? When used in oil drilling well control system, it is superior to ordinary hard pipes, safe and reliable, easy to install and disassemble, time-saving, labor-saving, corrosion resistant, maintenance free, and long service life. Fire resistance: it can work for 15 minutes at 750 ℃. Oil resistance: Immerse in hydraulic oil at 40 ℃ - 100 ℃ for 24 hours without deterioration or falling off.
