The hard core method adopts the core extrusion process to extrude the inner rubber tube blank, which directly uses the extruder to cover the inner rubber tube blank on the iron core, instead of the traditional casing process, and simplifies the process flow. Lanzhou Flange rubber pipe The billet forming adopts the process method of intertwining outer film and steel wire braiding forming. Similar to wrapping water wrapped cloth, the overlapping width is 1/2 of the film width. This process method can replace the method of wrapping outer film by extruder or by hand, reducing energy consumption and cost. We all know that the reinforcing layer and reinforcing layer of the rubber hose are the main force bearing parts, which are used to bear the load pressure. The factors determining the stress condition of the reinforced layer of the rubber hose are determined by the tension of the braided steel wire and the braiding angle. The high-speed steel wire hose braiding machine developed by our factory has introduced the advanced technology of foreign braiding production lines, and integrated the characteristics of domestic braiding machines. It integrates the advanced functions of hydraulic brake hose braiding production line, such as horizontal mechanical transmission, automatic lubrication, and so on, to develop equipment with high productivity and high degree of automation. The range of braiding diameter can be achieved Ф 6— Ф 25 Long core rubber hose (reinforcement layer). It fills the gap of domestic knitting production equipment, which can be widely used in rubber and plastic hose, rubber hose (reinforcement layer) knitting production equipment. The structure of high-pressure rubber hose is composed of four parts: inner liner, inner rubber layer, skeleton layer, middle rubber layer and outer rubber layer. Flange rubber pipe Where can I find it? In case of direct contact with the conveying medium, the synthetic rubber with good medium resistance, high tensile strength, high constant tensile stress, small compression permanent deformation and easy processing is usually selected. In order to meet the use requirements of strong polar medium resistance, the inner liner is composed of polytetrafluoroethylene layer and rubber layer, and a layer of film or adhesive is added on the surface of the inner liner to improve the adhesion with the skeleton material.

Many people have never understood high quality Flange rubber pipe It is better to use cast iron or rubber lining plate, so today I will give you a detailed analysis. The lining plate of the ball mill can tell you for sure that it is better to use rubber lining plate, which is also a trend for rubber lining plate to replace manganese steel lining plate. The rubber lining plate has many advantages that can not be achieved by manganese steel lining plates such as cast iron, so it has more advantages. One of the advantages of using cast iron or rubber liner for ball mill liner is that the noise of rubber liner is lower. In the process of grinding the rubber lining plate with materials, the noise is lower because it is not directly rubbed. Moreover, the rubber lining plate can throw the steel ball up for the second time to form the second grinding of materials, which makes the grinding of materials more thorough and the grinding fineness more uniform with good effect. In addition, the rubber lining plate can reduce the noise by an average of 30 dB compared with the noise of the cast iron lining plate, making it acceptable. Another important reason is energy saving. Energy consumption is an unavoidable problem for users of ball mills, because the cast iron lining plate is heavy in quality, Flange rubber pipe Where can I find it? Therefore, when the motor drives the lining plate, it will consume a lot of power. The rubber used by the rubber lining plate itself is light, so the electric energy consumed by the motor when driving is very small, which can be more than 10000 yuan of electric energy a year.

Due to the limitation of spatial location conditions, high quality Flange rubber pipe The installation stress of can often bring various difficulties to the installation work: formed pipes cannot be installed; When you bend down, you are about to come. If you make do with pipes, local cold correction will inevitably occur. According to the size of the pipeline and the specific situation on site, the cold correction amount varies from several millimeters to tens of millimeters, some as high as hundreds of millimeters. Practice has proved that the greater the quantity, the higher the internal stress. These residual installation stresses in the rubber sand blasting pipe are undoubtedly huge hidden information. The lubricating oil duct of a certain type of engine bearing was broken for many times due to excessive installation stress in actual operation. Because it can be bent at will, the internal stress generated by bending under the condition of rated bending radius is very small, which brings great convenience to the installation work, and also plays a certain role in ensuring the safe operation of the rubber sand blasting pipe. This is the main reason why some rubber sand blasting pipes must be used. Since it is necessary to load and unload the mold, the movable cylinder on the vulcanizer will move up and down. After repeated reciprocation, the copper serpentine tube will undergo fatigue fracture. Although it can continue to be used after repair, stopping for repair will cause time loss. Lanzhou Flange rubber pipe Although it has good flexibility and strong fatigue resistance, it is also weak in pressure bearing, temperature resistance, aging resistance and other aspects, and can not be used after several months. The good comprehensive performance of rubber sand blasting pipe is fully reflected here.

Lanzhou Flange rubber pipe It is used for transportation, construction and other operating equipment. Incorrect operation and incorrect environment may affect the normal use of steel braided sandblasting pipe. What specific factors will affect the normal use of steel braided sand blasting pipe? The quality will definitely affect the use effect. The poor quality is actually related to the selected raw materials. Some raw materials are of high quality, and the quality of steel braided sandblasting pipes produced is also very good. However, if the steel braided sand blasting pipe is made of inferior plastic, the quality is very poor, which also affects the use effect. The use environment affects the use effect. Anti static steel braided sand blasting pipe is usually used in industry. Because these products are very common, the demand is also large. However, people do not pay attention to the use environment. If used in strong acid and alkali environment, steel braided sand blasting pipe will naturally corrode. Or if used in a relatively high temperature area, the steel braided sandblasting pipe may melt. Anti static steel braided sand blasting pipe will also affect the use effect. In the eyes of most users, the greater the degree, the better the nature. So if you choose a good one, users can use it with confidence. Understanding and avoiding the wrong use of high-pressure pipeline can reduce the possibility of high-pressure pipeline failure. The following brief introduction will help you. 1. Frequent and serious pressure shock: high-pressure pipeline burst is generally not caused by excessive static pressure, but is related to the severity and frequency of pressure shock. During the operation of construction machinery, the sudden increase or decrease of oil pressure in the high-pressure pipe will occur repeatedly, which will cause frequent pressure shocks to the oil pipe, leading to the aggravation of oil seal damage at various parts, blistering and cracking of rubber hose, and loosening and leakage of pipe joints. Therefore, during operation, the valve rod shall not be pulled too hard, but must be pulled gently. 2. The use temperature of oil is too high: during the operation of construction machinery, due to the power loss of the hydraulic system, the oil will rise, and the external temperature (especially in summer) will lead to a sharp rise in the oil temperature. high quality Flange rubber pipe Where can I find it? The higher the oil temperature is, the easier the rubber is to age, the worse the elasticity is, the lower the strength and sealing performance are, and the high-pressure pipe will burst rapidly. Therefore, when the temperature rise of the hydraulic system is too high or too fast during operation, the causes should be found out and eliminated in time. For summer operation, especially continuous operation, necessary cooling measures shall be taken.