Handan Oxygen tube With the continuous updating of technology, the products are also developing in the continuous updating. At present, the inspection requirements of rubber hose are also improved compared with the previous ones. The inspection index of ultra-high pressure hose shall meet the following index requirements according to the requirements of the Safety Code for High Pressure Water Jet Cleaning Operation: 1) The bursting pressure shall be more than 2.5 times of the working pressure. 2) The test pressure shall be 1.5 times of the working pressure, and the pressure shall be kept for more than 2 minutes without damage. 3) Pulse pressure shall be within the range from zero to working pressure, and 50000 pressure pulses shall be free of damage; The pulse frequency is 15 times/min when the working pressure is 1000-2800bar, and 110 times/min when the pressure is above 2800bar. Since high-pressure cleaning machine has been widely used in all walks of life, and the working condition of high-pressure hose is relatively the worst, we must pay attention to the quality when selecting high-pressure hose, so as to avoid unnecessary safety accidents. Oxygen tube Where can I find it? The development of rubber hose can not be separated from cooperation, R&D and innovation can not be separated from communication, and the inspection requirements of rubber hose have been improved compared with the previous ones. The storage site shall be free of ozone, heat source and equipment generating electromagnetic field. The coiled hoses or hose assemblies shall be stored horizontally, and the stacking height shall be limited to the extent that the products at the bottom will not produce permanent deformation.

Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Handan Oxygen tube It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Oxygen tube Where can I find it? The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.

Handan Oxygen tube The entry threshold is low, the industry market is mixed, and small enterprises with small scale, lack of core competitiveness and low technical level can be seen everywhere. Most of these enterprises lack brand awareness, and there are many brand names and unlicensed products. It is difficult to form enterprise influence through brands, and it is more difficult to improve product added value through brands. If the metal hose wants to take the road of high-end, it must improve both inside and outside. A good brand image promotion and influence building can certainly provide a strong driving force for the development of enterprises, but the root of this driving force lies in the high quality of the metal hose products themselves. Tongfeng Metal Hose said that in the future, domestic metal hose products will focus on high precision, high efficiency, high firmness, multi-function, multi specification, multi variety standardization, serialization and generalization to show their characteristics. One of the main reasons why China's metal hoses have been in the low-end state for a long time is the lack of independent research and development of products. On the one hand, the homogenization competition is serious. In order to win consumers, metal hose enterprises have long focused on low-cost competition and low price shopping. As a result, many enterprises only focus on the production and marketing of low-end products, ignoring the upgrading and innovation of product technology. on the other hand, Oxygen tube Where can I find it? ZHUANLI's weak awareness of protection and the serious phenomenon of technology plagiarism and infringement in the industry make the technology cost invested by many enterprises more than worth the cost, which has seriously hit the enthusiasm of metal hose enterprises for innovation.

one Handan Oxygen tube When using, the talcum powder on the inner wall of the hose must be blown clean to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with acids, alkalis, oils and other organic solvents that can damage the hose. The storage temperature shall be - 15~40 ℃, and the distance from the heat source shall not be less than 1m. 3. According to the national standards, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; The acetylene hose is black, the working pressure vessel is 0.3MPa, the inner diameter of the hose is 8mm, and the outer diameter is 16mm. 4. The gas cutting operation requires a large oxygen output, so the valves of the gas cylinder (or oxygen pipeline) connected to the high pressure end of the oxygen meter should be fully opened to ensure adequate flow and stable pressure. The low pressure gauge has indicated the working pressure, but the pressure drops suddenly when using oxygen. At this time, it is easy to backfire and may backfire into the oxygen hose to cause explosion. 5. Oxygen hose and acetylene hose shall not be mixed or substituted with each other, and oxygen and hose shall not be used to blow away the blockage of acetylene hose. At the same time, it is necessary to check and eliminate the defects such as gas leakage and blockage of the welding torch at any time to prevent the formation of oxygen and acetylene mixture in the hose. It should be pointed out that the hose color specified in the national standard is opposite to that specified in the international standard (ISO) (oxygen hose is black, acetylene hose is red). At the same time, it is different from the original ministerial standard (HG4-605-66) that oxygen hose is red and acetylene hose is green. Before 1966, domestic oxygen hose was black or green and acetylene hose was red. thus Oxygen tube Where can I find it? It causes inconsistency between the understanding and habits of the supply department and the user, and is easy to cause accidents due to the mixing and substitution of rubber hoses. At present, it should be emphasized that unified understanding and use should be carried out in accordance with the provisions of national standards, and attention should be paid to distinguishing the rubber hoses of imported equipment.

The air conditioning in the hall of a giant building is provided by the 6FWB unit fixed in the basement. production Oxygen tube The vibration of the unit is transmitted to the ground hall through the bridge connecting the sand blasting hose pipe, and the noise value reaches 45dB. In such an environment, people always feel uncomfortable. After the improved design, sandblasting rubber pipes were connected in series on the connecting pipes, which not only absorbed some of the noise generated by the unit vibration, but also the noise generated by the fluid pulsation in the pipeline system. At this time, the noise value in the ground hall was only 33dB, greatly improving the environment in the hall. The movable cylinder on the vulcanizing press will move upward and downward for the need of loading and unloading the mold. After repeated reciprocating movements, the copper serpentine will suffer from fatigue fracture. Although it can still be used after repair, it will cause time loss if it is stopped for repair. Oxygen tube Where can I find it? Although it has good soft properties and strong fatigue resistance, it is weak in pressure bearing, temperature resistance, aging resistance and other aspects, and can not continue after several months of use. The good comprehensive performance of sand blasting hose is fully reflected here. In the general industrial field, in addition to pressure and temperature, there are often severe conditions such as fatigue, corrosion, vibration, compression, impact, etc. Under such circumstances, it is most appropriate to use sandblasting hose to compensate for the position movement of the pipeline.

Handan Oxygen tube The structure is composed of liquid resistant synthetic rubber inner rubber layer, medium rubber layer, I or II or III steel wire braid reinforcement layer, and weather resistant synthetic rubber outer rubber layer. Sand pumping hose features: 1. Sand pumping hose is made of special synthetic rubber, which has excellent oil resistance, heat resistance and aging resistance. 2. The rubber hose has high bearing pressure and excellent pulse performance. 3. The pipe body is tightly combined, soft to use, and has little deformation under pressure. 4. Sand pumping hose has excellent bending resistance and fatigue resistance. 5. The sand pumping hose is long, φ 20 meters above 32, φ Below 25 meters, it can reach 10 meters or even 100 meters. Sand pumping hose parameters: 1. The inner wall of nylon cord hose is smooth with little friction. Reinforcing layer: high-strength synthetic wire, spiral winding of steel wire and iron wire (sand suction pipe) 2 production Oxygen tube Flange connection (ANSI150 standard flange) 3. Nominal pressure: 20BAR4, temperature: - 50 ℃ -+95 ℃ 5. Working pressure of sand suction hose and mud discharge pipe: positive pressure: 10kg; Test pressure: working negative pressure of 15kg steel ring sand suction hose: ≥ 15kg sand suction hose has strong flexibility, which is mainly used as the sand pump sand discharge pipe to connect the sand transport pipe and sand pump, as well as the pipe connection bend.