Yunnan Suction pipe Vulcanization of technical performance indicators is an important process to enhance the adhesive strength between rubber and reinforcement layer and make it a whole in rubber hose manufacturing, and also an important link to ensure and improve product quality. In order to obtain good pulse performance and service performance of steel wire reinforced rubber hose, in addition to reasonable structure and formula, it is necessary to ensure the compactness of vulcanized hose. In order to meet this performance requirement, the traditional vulcanization method is to wrap the water in water cloth on the semi-finished hose before vulcanization, make braided hose or steel wire for reinforcement and fastening, and vulcanize in batches with steam vulcanization tank. Since the performance requirements of medium and low pressure hoses are low, the rubber hose can also be directly put into the curing tank without fastening. Although water wrapped cloth vulcanization can also increase the compactness of the hose, its appearance is poor. In order to obtain the smooth outer surface of the hose, the lead coating vulcanization method is widely used at home and abroad. For decades, people have been using this method as an effective method to vulcanize and strengthen rubber hoses, especially high-pressure rubber hoses. So far, many domestic and foreign manufacturers are still using this method to produce rubber hoses. But the fatal disadvantage of this method is that it pollutes the environment. Suction pipe Price The main control function of the air compressor station unit is to exhaust more air. According to different structures, it can be divided into full hose, cloth hose, steel braided hose, etc. According to different uses, it can be divided into air hose, water suction hose, water delivery hose, heat resistant hose, acid (alkali) resistant hose, oil resistant hose and special hose., It can be closed within the specified range.
Many people have never understood high quality Suction pipe It is better to use cast iron or rubber lining plate, so today I will give you a detailed analysis. The lining plate of the ball mill can tell you for sure that it is better to use rubber lining plate, which is also a trend for rubber lining plate to replace manganese steel lining plate. The rubber lining plate has many advantages that can not be achieved by manganese steel lining plates such as cast iron, so it has more advantages. One of the advantages of using cast iron or rubber liner for ball mill liner is that the noise of rubber liner is lower. In the process of grinding the rubber lining plate with materials, the noise is lower because it is not directly rubbed. Moreover, the rubber lining plate can throw the steel ball up for the second time to form the second grinding of materials, which makes the grinding of materials more thorough and the grinding fineness more uniform with good effect. In addition, the rubber lining plate can reduce the noise by an average of 30 dB compared with the noise of the cast iron lining plate, making it acceptable. Another important reason is energy saving. Energy consumption is an unavoidable problem for users of ball mills, because the cast iron lining plate is heavy in quality, Suction pipe Price Therefore, when the motor drives the lining plate, it will consume a lot of power. The rubber used by the rubber lining plate itself is light, so the electric energy consumed by the motor when driving is very small, which can be more than 10000 yuan of electric energy a year.
Yunnan Suction pipe It is composed of sand blasting hose, net sleeve and joint. The sand blasting hose is the main body of the rubber sand blasting pipe, playing a flexible role, and the net plays a role of strengthening and shielding; Joints play the role of connection. For different use requirements, they are connected in different ways: sandblasting hose, net sleeve and joint are connected by welding, which is called welding type; The connection in the form of mechanical clamping is called mechanical clamping. In addition, the combination of the above two methods is called hybrid clamping. Rubber sand blasting pipe products include oil suction hose, steam hose, sand blasting hose, acid and alkali suction hose, food hose, oxygen blowing hose and various special-shaped hoses. It is widely used in machinery, chemical industry, petroleum, metallurgy, food and other industries. What is the pressure range of pressure resistant rubber sand blasting pipe: the pressure range of hose is generally Pn 0.6-32.0 MPa. The rubber sand blasting pipe up to 42.0 MPa is the main pressure bearing part of the hose installed in the pressure pipe, and it acts as the sheath of the sand blasting hose. Suction pipe Price One or more layers of stainless steel wire or steel strip can be selected for braiding according to the pressure in the pipeline and the place of use. It can also achieve the effect of reducing noise. This is why some rubber sand blasting pipes use rubber sand blasting pipes.
With the development of modern industry, the demand for high temperature and high pressure sandblasting hoses is growing, Suction pipe Price Scope of application: completely flexible conveying pipe is required to prevent the pipe from being in vibration position. It is suitable for steam, gas, air, heavy oil, petroleum, chemical industry, etc. First of all, the structure of fire sprinkler metal sandblasting hose (explosion-proof pipe) must have compulsory knowledge. Fire sprinkler metal sandblasting hose (hereinafter referred to as explosion-proof pipe) is a high-quality sandblasting hose in modern industrial pipelines. It is mainly composed of fire sprinkler metal sandblasting hose bellows, fire sprinkler metal sandblasting hose net sleeve and fire sprinkler metal sandblasting hose connector. The inner pipe is a thin-walled stainless steel fire sprinkler metal sandblasting hose corrugated pipe with spiral or circular waveform. The outer layer of the fire sprinkler metal sandblasting hose corrugated pipe is woven by stainless steel wire or steel strip according to certain parameters. The fire spraying metal sand blasting hose connector or flange at both ends of the sand blasting hose shall match with the fire spraying metal sand blasting hose connector or flange of the user's pipeline. high quality Suction pipe Scope of application of fire sprinkler metal sandblasting hose (explosion-proof pipe): full flexible conveying pipe is required in vibration places to prevent pipes, which is applicable to steam, gas, air, heavy oil, petroleum, chemical industry, etc. The annular flame spraying metal sandblasting hose bellows is a special geometric pipe. The outer edges of several annular diaphragms are tangent to several concave half rings facing the center, and the inner edges are tangent to several concave half rings of the vest. Its blanks are mainly made of tubes. The fire sprinkler metal sandblasting hose bellows has the characteristics of large flexibility, good elasticity, simple manufacturing and small rigidity.
Yunnan high quality In places that must be crossed or may rub with the mechanical surface when working, hose clamps or springs and other protective devices should be used to prevent the outer layer of the sandblasting hose from being damaged. Sand blasting hose shall be arranged to avoid heat source as far as possible and away from the performance of engine exhaust pipe. If necessary, sleeve or protective screen can be used to prevent the hose from being heated and deteriorated. When the sand blasting hose must be bent, the bending radius should not be too small, and should be greater than 9 times the outer diameter. There should be a straight line section greater than 2 times the outer diameter of the pipe at the joint between the rubber hose and the joint. How high-quality the products and equipment we use are, it is inevitable that there will be some large and small failures in the process of using them, which will more or less have a certain impact on our work. Just like the use of sandblasting hose, there are traces of its outer adhesive seam, problems must be solved, For this, we explained the following solutions: First, the used water cloth should be used according to the original elastic edge of the water cloth when it is reused. 2： When we wrap the water cloth around the seam of the sandblasting hose, we should apply sufficient and uniform pressure to the pipe body. 3. The water cloth with different widths should be selected according to the size of the outer diameter of the wrapped sandblasting hose (for hose with an outer diameter of less than 30mm, the width of the water cloth should not exceed 90mm). The overlapping width of the water cloth should be 3/5-2/3 of the width of the water cloth.
