wear-resisting Large diameter suction pipe It will burst for a long time due to frequent and severe pressure shocks. This situation is usually not caused by excessive static pressure, but is related to the strength and frequency of pressure shock. During the operation of construction machinery, the oil pressure in the oil resistant hose will rise or fall repeatedly, and then it will form frequent pressure shocks to the oil pipe, causing the oil seal of each part to become more damaged, the oil resistant hose will bubble and break, and the pipe joint will become loose and leak. Therefore, in the process of operation, the valve rod should not be pulled too hard, and it needs to be gentle. The application temperature of the oil in the oil resistant rubber hose is too high, resulting in aging and bursting of the rubber hose. During the operation of construction machinery, the hydraulic system will cause the oil to become hot due to power failure, and the influence of external temperature (especially in summer) will cause the oil temperature to rise sharply. The higher the oiling temperature is, the easier the rubber hose ages, the worse the elasticity is, the lower the strength and sealing function are, and the oil resistant hose will burst quickly. Therefore, Large diameter suction pipe company During operation, when the temperature rise of the hydraulic system is too high or too fast, the causes should be found and eliminated in time. Necessary cooling measures shall be taken for summer operation, especially continuous operation.

As wear-resisting Large diameter suction pipe As an important part of sand blasting machinery, its safety plays a vital role in the safety of equipment operation. The following will briefly analyze the precautions in the use of high-pressure sandblasting pipe: I. Pipe inner diameter: inner diameter of high-pressure sandblasting pipe. 2、 Attention shall be paid to the following items in the use and design of high-pressure sandblasting pipe: 1. The bending radius of high-pressure sandblasting pipe shall not be too small, and generally shall not be less than the value specified in the assembly technology of high-pressure sandblasting pipe. The joint between the high-pressure sandblasting pipe assembly and the pipe joint shall have a straight section, and its length shall not be less than twice the outer diameter of the pipe. 2. The length of high-pressure rubber hose assembly shall consider that the high-pressure rubber hose will shrink and deform after introducing pressure oil. Generally speaking, the shrinkage rate is 3~4 times of the pipe length. When installing the high-pressure rubber hose assembly, it is not allowed to bear tension. 3. During installation, the high-pressure sandblasting pipe assembly shall be free from torsional deformation. Large diameter suction pipe company The connecting shaft of shall be placed in the moving plane as far as possible to avoid damaging the high-pressure sandblasting pipe when both ends move with each other. 4. High pressure resistant sand blasting pipe shall avoid contact and friction with mechanical sharp corners to avoid damaging the pipe. Safety measures: to ensure the safe and reliable use of high-pressure sandblasting pipe assembly.

polyurethane wear-resisting Large diameter suction pipe Maintenance measures; Cleaning: It is recommended to empty the hose after use. Clean if necessary. Inspection: After each use, the rubber tube must be inspected to ensure that there is no structural damage. Pressure: If the rubber pipe is under great pressure during use, or the outer layer of the rubber pipe will contact with the conveyed liquid for a long time, it is recommended to conduct a hydrostatic test. Due to the natural characteristics of rubber, the physical properties and performance levels of all rubber products will change. This change usually occurs over time, depending on the type of rubber used. However, changes may also accelerate due to several factors or a combination of several factors. Other materials used to reinforce rubber tubing may also be adversely affected by improper storage conditions. Detailed step 1. Polyurethane sand blasting pipe mandrel: the mandrel is usually pulled backward, mainly to increase the firmness of the connection between the mandrel and the hose. After the spindle barb processing is completed, the barb tip must also be passivated, otherwise the barb tip will pierce the lining material of the high-pressure rubber tube during the buckling process. Large diameter suction pipe company Even if the high-pressure rubber pipe joint is firmly buckled, if the inner layer is damaged, high-pressure water will leak from the buckle. 2. Polyurethane sand blasting pipe sheath: the sheath is generally in the form shown in the figure, the wall thickness should be moderate, and the internal rectangular tooth height should not exceed 2mm, that is, (d-d) should not exceed 4mm.

Nanning Large diameter suction pipe It is one of the most common rubber products in life, used to transport various gases and liquids. Natural rubber, synthetic rubber and reclaimed rubber in rubber products can be used for the consumption of rubber sand blasting pipes. When reclaimed rubber is used to consume odorless rubber sand blasting pipe, care must be taken in selecting reclaimed rubber and formula design to meet the performance requirements of odorless rubber sand blasting pipe. When using recycled rubber to consume odorless rubber sand blasting hose, what problems should we pay attention to? The selection of reclaimed rubber for odorless rubber sandblasting hose is the basis for determining the quality of rubber, whether it is environmental protection rubber products or various odorless rubber products. When using reclaimed rubber to consume odorless hose, choosing odorless reclaimed rubber is the top priority. Application of odorless reclaimed latex, odorless reclaimed tire rubber, odorless reclaimed nitrile rubber and odorless reclaimed ethylene propylene rubber in reclaimed rubber products. The odorless butyl reclaimed rubber can be used for the consumption of odorless rubber sandblasting pipes. In addition, odorless hb isoprene reclaimed rubber can also be used for consumption of odorless rubber sandblasting pipes. In actual consumption, the raw materials of odorless isoprene reclaimed rubber (PP reclaimed rubber) are isoprene unvulcanized composite rubber and isoprene bottle stopper. They have strong viscosity, aging resistance and temperature resistance, and are ideal for odorless hose consumption to ensure quality and reduce costs. Pay attention to the vulcanization of odorless rubber sand blasting pipe. as everyone knows, Large diameter suction pipe company The design of vulcanization system of reclaimed rubber products directly affects the quality of rubber products, and the odorless rubber sand blasting pipe of reclaimed rubber is no exception. When using reclaimed rubber to consume odorless rubber sand blasting pipe products, vulcanizing agent, accelerator and other additives must be combined with odorless additives such as accelerator STT and accelerator D; When vulcanizing the rubber of odorless rubber sand blasting pipe, it is better to vulcanize at low temperature for a long time, which will cause full reaction to the rubber.