high quality Oil hose Acid and alkali resistance: there is no obvious change after soaking in 44 solutions for 24 hours; Pressure resistance: under the pressure of 52.5 MPa, the pressure is stable for 5 minutes without leakage, the surface of the pipe body is not deformed, and the damage pressure is greater than 105 MPa; Heat preservation: place the pipe in an environment of 300-50 ℃, with clear water in the pipe for 20 minutes, and the temperature ratio inside and outside the pipe is 1:40. The wear-resistant sand blasting hose is a material conveying pipe. The wear-resistant sand blasting hose is a material conveying pipe. Common black, yellowish or transparent; Most of them are wrapped by external rubber packing belt, and the steel wire is usually set between the internal and external rubber for negative pressure operation. The utility model is mainly used for conveying liquid containing solid particles such as particles, gravel, cement, quicksand, concrete, gypsum, etc., and is suitable for various tunnel projects, shafts, tunnels, and other engineering operations. The inner rubber and outer rubber of sand blasting pipe made of ordinary materials are usually made of wear-resistant materials, most of which are nitrile rubber (acrylonitrile butadiene copolymer), styrene butadiene rubber (oil extended styrene butadiene rubber), etc., Or PARA rubber (trefoil rubber), the inlet hose has better performance. According to the working conditions and the degree of loss of material particles to the transmission medium, the sand blasting pipe is generally divided into light sand blasting pipe and heavy sand blasting pipe. Spiral wire will make them suitable for negative pressure environment. Light sandblasting pipe Light sandblasting pipe Light sandblasting pipe is usually used in marine sandblasting and quicksand operations. The ordinary inner rubber is made of wear-resistant nitrile rubber (NBR), while the outer rubber is wrapped with composite rubber. Heavy sandblasting pipe Heavy sandblasting pipe Heavy sandblasting pipe is used for sandblasting sand, pebble, mud, etc. Equipment. Oil hose Where can I find it? Sand blasting vacuum tube Sand blasting vacuum tube The sand blasting vacuum tube is embedded with spiral steel wire, and the general vacuum negative pressure can reach 0.9 bar. Common parameter definitions The wear-resistant sandblasting pipe generally has the following parameters: folding pressure is generally within 12 bar, higher sandblasting pressure can reach 36 bar, and sometimes vacuum negative pressure parameters such as 0.8 bar~0.9 bar are required.
The hard core method adopts the core extrusion process to extrude the inner rubber tube blank, which directly uses the extruder to cover the inner rubber tube blank on the iron core, instead of the traditional casing process, and simplifies the process flow. Linyi Oil hose The billet forming adopts the process method of intertwining outer film and steel wire braiding forming. Similar to wrapping water wrapped cloth, the overlapping width is 1/2 of the film width. This process method can replace the method of wrapping outer film by extruder or by hand, reducing energy consumption and cost. We all know that the reinforcing layer and reinforcing layer of the rubber hose are the main force bearing parts, which are used to bear the load pressure. The factors determining the stress condition of the reinforced layer of the rubber hose are determined by the tension of the braided steel wire and the braiding angle. The high-speed steel wire hose braiding machine developed by our factory has introduced the advanced technology of foreign braiding production lines, and integrated the characteristics of domestic braiding machines. It integrates the advanced functions of hydraulic brake hose braiding production line, such as horizontal mechanical transmission, automatic lubrication, and so on, to develop equipment with high productivity and high degree of automation. The range of braiding diameter can be achieved Ф 6— Ф 25 Long core rubber hose (reinforcement layer). It fills the gap of domestic knitting production equipment, which can be widely used in rubber and plastic hose, rubber hose (reinforcement layer) knitting production equipment. The structure of high-pressure rubber hose is composed of four parts: inner liner, inner rubber layer, skeleton layer, middle rubber layer and outer rubber layer. Oil hose Where can I find it? In case of direct contact with the conveying medium, the synthetic rubber with good medium resistance, high tensile strength, high constant tensile stress, small compression permanent deformation and easy processing is usually selected. In order to meet the use requirements of strong polar medium resistance, the inner liner is composed of polytetrafluoroethylene layer and rubber layer, and a layer of film or adhesive is added on the surface of the inner liner to improve the adhesion with the skeleton material.
high quality Oil hose The inner rubber layer of（ ф 0.3-2.0 reinforcement layer) is the skeleton material that plays the role of reinforcement. What should be paid attention to when storing the wear-resistant sandblasting pipe. 1. The wear-resistant sandblasting pipe should be stored as loose as possible. Generally, rubber hoses with inner diameter less than 76 mm can be wound and stored. 2. During the storage of wear-resistant sand blasting pipe, it is strictly prohibited to stack heavy objects on the pipe body to prevent external extrusion and damage. 3. During the storage of wear-resistant sand blasting pipe, do not contact with acid, alkali, oil, organic solvent or other corrosive liquids and gases, and the heat release should start from 1m away. 4. The storage period of wear-resistant sand blasting pipe shall not exceed 2 years, and it shall be used by the first person to prevent the quality of rubber pipe from being affected by long-term storage. 5. When wear-resistant sand blasting pipes need to be temporarily stored in the open air, the site should be flat and the rubber pipe should be laid flat. The upper cover should be placed under the rubber pipe and no heavy objects should be stacked. At the same time, the hose shall not contact the heat source. 6. The storage place of the upper and lower rubber pipes in the well shall be kept clean and ventilated, and the relative humidity shall be 80. The temperature of the storage place shall be kept between - 15 ℃ and 40 ℃, and the rubber pipe shall be protected from direct sunlight and water spray. 7. When storing wear-resistant sand blasting pipe, Oil hose Where can I find it? Both ends of the hose shall be sealed firmly to prevent sundries from entering the hose. 8. When the wear-resistant sand blasting pipe is stored, it should be placed separately according to different varieties and specifications, not mixed, and hang the management board. 9. In order to prevent the pipes from being pressed and deformed during storage, they should not be stacked too high, and the stacking height should not exceed 1.5m. It also requires rubber hoses to be "stacked" frequently during storage, at least once a quarter.
The air conditioning in the hall of a giant building is provided by the 6FWB unit fixed in the basement. high quality Oil hose The vibration of the unit is transmitted to the ground hall through the bridge connecting the sand blasting hose pipe, and the noise value reaches 45dB. In such an environment, people always feel uncomfortable. After the improved design, sandblasting rubber pipes were connected in series on the connecting pipes, which not only absorbed some of the noise generated by the unit vibration, but also the noise generated by the fluid pulsation in the pipeline system. At this time, the noise value in the ground hall was only 33dB, greatly improving the environment in the hall. The movable cylinder on the vulcanizing press will move upward and downward for the need of loading and unloading the mold. After repeated reciprocating movements, the copper serpentine will suffer from fatigue fracture. Although it can still be used after repair, it will cause time loss if it is stopped for repair. Oil hose Where can I find it? Although it has good soft properties and strong fatigue resistance, it is weak in pressure bearing, temperature resistance, aging resistance and other aspects, and can not continue after several months of use. The good comprehensive performance of sand blasting hose is fully reflected here. In the general industrial field, in addition to pressure and temperature, there are often severe conditions such as fatigue, corrosion, vibration, compression, impact, etc. Under such circumstances, it is most appropriate to use sandblasting hose to compensate for the position movement of the pipeline.
Linyi Oil hose There are many specifications. Different installation positions require different specifications of cloth clamping sand blasting pipe, and the specification selection of cloth clamping sand blasting pipe has different requirements. The following small series will briefly introduce them to you: 1. Temperature: The selection should be based on the ambient temperature when the cloth clip sandblasting pipe is working. In case of high temperature, the temperature correction pressure shall be determined according to the working pressure and temperature correction coefficient of the cloth sanding pipe under high temperature to determine the correct pressure level. 2. Pressure: when selecting the cloth clip sandblasting pipe, check the nominal diameter and pressure gauge of the corrugated cloth clip sandblasting pipe according to the actual working pressure of the hose to determine whether to use the stainless steel mesh sleeve type. 3. Size: select the joint type, size of cloth sanding pipe and hose length according to the size of cloth sanding pipe. 4. Medium: determine the material of each part of the hose according to the chemical properties of the material medium transported in the cloth sanding pipe and the corrosion resistance of the hose material. 5. Status: According to the use status of the hose, refer to the correct use and installation method of the cloth clip sandblasting pipe and the length of the hose in the settlement compensation. Therefore, Oil hose Where can I find it? According to the actual pressure of the system, the higher the working pressure of the cloth clamping sand blasting pipe is, the normal operation of the system can be ensured, and the appropriate cloth clamping sand blasting pipe is selected.
