Sichuan Flange rubber pipe Also called rubber hose for sand blasting. It is suitable for air pressure sand blasting of metal surface for rust removal, hemp removal, and sand blasting rubber hose for wet sand blasting and dry sand blasting in engineering construction. It is suitable for air pressure sand blasting of metal surface for rust removal, hemp removal, and sand blasting rubber hose for wet sand blasting and dry sand blasting in engineering construction. The common application fields are shipbuilding, machining, spraying industry, etc. Appearance of abrasion resistant sand blasting rubber hose: 1. Light abrasion resistant sand blasting rubber hose consists of black, yellowish or transparent abrasion resistant rubber inner layer, central fabric or cord reinforcement layer, medium rubber layer and outer rubber layer; 2. Heavy abrasion resistant rubber hose consists of black, yellowish or transparent abrasion resistant rubber inner layer, cloth clip or cord reinforcement layer, steel wire framework reinforcement layer, medium rubber layer Composition of outer rubber layer 3. The steel wire braided wear-resistant sandblasting hose is composed of black, yellowish or transparent wear-resistant rubber inner layer, single-layer or multi-layer steel wire braided reinforcement layer, medium rubber layer and outer rubber layer. Purpose Abrasion resistant sand blasting hose is a kind of material conveying pipe, which is mainly used for conveying solids containing particles such as particles, gravel, cement, quicksand, mud, gypsum, etc. It is suitable for various tunnel projects, tunnels, caverns and other engineering operations. The general working pressure is less than 12 bar, and the higher bursting pressure can reach 36 bar. Sometimes the vacuum rich negative pressure parameter is 0.8 bar 0.9 bar. Flange rubber pipe Price Hydraulic requirements 1. The maximum working pressure of wear-resistant sand blasting hose is 0.63MPa. 2. The hose shall be free from water seepage, local bulge, expansion and other abnormalities when conducting hydraulic test under twice the working pressure. Keep the pressure of anti-static hose for 1min, and the length change shall not exceed ± 0.8%, the outer diameter change shall not exceed ± 10%, and the torsion per meter shall not exceed 60 º. 3. The bursting pressure of the hose shall not be less than 4 times of the working pressure.

Sichuan wear-resisting In places that must be crossed or may rub with the mechanical surface when working, hose clamps or springs and other protective devices should be used to prevent the outer layer of the sandblasting hose from being damaged. Sand blasting hose shall be arranged to avoid heat source as far as possible and away from the performance of engine exhaust pipe. If necessary, sleeve or protective screen can be used to prevent the hose from being heated and deteriorated. When the sand blasting hose must be bent, the bending radius should not be too small, and should be greater than 9 times the outer diameter. There should be a straight line section greater than 2 times the outer diameter of the pipe at the joint between the rubber hose and the joint. How high-quality the products and equipment we use are, it is inevitable that there will be some large and small failures in the process of using them, which will more or less have a certain impact on our work. Just like the use of sandblasting hose, there are traces of its outer adhesive seam, problems must be solved, For this, we explained the following solutions: First, the used water cloth should be used according to the original elastic edge of the water cloth when it is reused. 2： When we wrap the water cloth around the seam of the sandblasting hose, we should apply sufficient and uniform pressure to the pipe body. 3. The water cloth with different widths should be selected according to the size of the outer diameter of the wrapped sandblasting hose (for hose with an outer diameter of less than 30mm, the width of the water cloth should not exceed 90mm). The overlapping width of the water cloth should be 3/5-2/3 of the width of the water cloth.

wear-resisting Flange rubber pipe The inner rubber layer of（ ф 0.3-2.0 reinforcement layer) is the skeleton material that plays the role of reinforcement. What should be paid attention to when storing the wear-resistant sandblasting pipe. 1. The wear-resistant sandblasting pipe should be stored as loose as possible. Generally, rubber hoses with inner diameter less than 76 mm can be wound and stored. 2. During the storage of wear-resistant sand blasting pipe, it is strictly prohibited to stack heavy objects on the pipe body to prevent external extrusion and damage. 3. During the storage of wear-resistant sand blasting pipe, do not contact with acid, alkali, oil, organic solvent or other corrosive liquids and gases, and the heat release should start from 1m away. 4. The storage period of wear-resistant sand blasting pipe shall not exceed 2 years, and it shall be used by the first person to prevent the quality of rubber pipe from being affected by long-term storage. 5. When wear-resistant sand blasting pipes need to be temporarily stored in the open air, the site should be flat and the rubber pipe should be laid flat. The upper cover should be placed under the rubber pipe and no heavy objects should be stacked. At the same time, the hose shall not contact the heat source. 6. The storage place of the upper and lower rubber pipes in the well shall be kept clean and ventilated, and the relative humidity shall be 80. The temperature of the storage place shall be kept between - 15 ℃ and 40 ℃, and the rubber pipe shall be protected from direct sunlight and water spray. 7. When storing wear-resistant sand blasting pipe, Flange rubber pipe Price Both ends of the hose shall be sealed firmly to prevent sundries from entering the hose. 8. When the wear-resistant sand blasting pipe is stored, it should be placed separately according to different varieties and specifications, not mixed, and hang the management board. 9. In order to prevent the pipes from being pressed and deformed during storage, they should not be stacked too high, and the stacking height should not exceed 1.5m. It also requires rubber hoses to be "stacked" frequently during storage, at least once a quarter.

Although fire Sichuan Flange rubber pipe Explosion proof pipe) can be compressed and stretched, but if the installation position is incorrect, it will break quickly and reduce the service life. The sandblasting hose can be installed horizontally, vertically or obliquely. The most ideal condition is vertical installation. At the same time, avoid installing near the wheel, and install baffle if necessary. Generally speaking, the flame spraying metal sand blasting hose (explosion-proof pipe) can be divided into three lengths: the first is the compression length, that is, the length of the sand blasting hose when it is compressed to the limit position; The second is the installation length, that is, the length of the sandblasting hose when it is in the middle of half of the maximum displacement. The third type is the stretching length, that is, the length when the sandblasting hose is stretched to the maximum limit. When installing the sandblasting hose, the sandblasting hose should be in the middle position, which is called the installation length. When installed at this position, the sandblasting hose can move in two directions when bearing axial load. Otherwise, if it can only move in one direction, its strength will be affected and its service life will be reduced. In the actual installation process, considering that measuring the length of the sandblasting hose with a ruler according to the calculation results may affect the production efficiency, some foreign manufacturers directly install the ruler on the sandblasting hose, and cut the ruler after installation. From the structural point of view, the metal flame spraying metal sandblasting hose (explosion-proof pipe) is composed of strip and tube parts, which can form annular flame spraying metal sandblasting hose bellows and spiral flame spraying metal sandblasting hose bellows. Flange rubber pipe Price Just because the corrugated pipe of the fire sprinkler metal sandblasting hose formed by this article always has a certain length of brazing or welding buckles and fire sprinkler metal sandblasting hose joints, the residues of the working medium often accumulate in these places, and the cleaning test and mechanical impurities in the working medium will deposit down to pollute the inner cavity. Therefore, its use reliability is relatively poor.

1. The use of protection cannot be ignored: the long-term use of high-pressure sand blasting hose joints at home usually does not cause concern, but excessive use and improper protection also buried the hidden danger of joint cracking to a certain extent. It is understood that the service life of the joint is usually 200000 times, and it should be replaced after long-term use. When using the side, Flange rubber pipe Price Care should be taken to close and open as gently as possible and not to rotate the knob of the hose connector repeatedly. 2. Differentiation of quality can be based on standard evidence collection. It is understood that it is still difficult to determine the cause of joint cracking. At present, the National Bureau of Technology and Quality Supervision has issued recommendations for sealing nozzles and hose specifications. These two specifications perfectly adjust the quality specification target of connectors and hoses. Consumers can go to the quality inspection department to check the torsional strength of the connecting hose, the tightness of the connecting spool and the strength of the connecting materials. If the content of standard rules cannot be met, it will be attributed to quality problems, which can serve as a strong basis for expression. 3. The appearance of hose connector is difficult to distinguish between good and bad. In order to pursue profits and reduce costs, many manufacturers currently use selected cast iron (easy to rust) and zinc alloy (non anti-corrosion) as materials to produce high-pressure sand blasting hose joints, which causes product quality problems. It is understood that the quality of connectors and hoses is not up to standard, Sichuan Flange rubber pipe The strength function and sealing function of high-pressure sand blasting hose joints are not up to standard due to problems such as materials and wall thickness, which should be paid attention to by consumers.

Sichuan wear-resisting Flange rubber pipe Plays an important role. In the application of different industries, according to their own needs, check the performance of the products, give proper play to the advantages of the products, and ensure the normal use of daily applications. When replacing the wear-resistant sand blasting pipe, the length of the rubber pipe, the number of steel wire layers, the shape and size of the joint should be reasonable, and the curvature of the rubber pipe should be minimized. When tightening the connecting nuts, do not tighten the rubber hose. Excessive bending and twisting will greatly reduce the service life of the rubber hose. Protective measures shall be taken for the parts liable to friction to prevent the rubber hose from bursting due to wear. What should we pay attention to when purchasing wear-resistant sandblasting pipe? Different types of wear-resistant sand blasting pipes have different working pressures. When purchasing rubber hose, you should first determine the working pressure of the system, Flange rubber pipe Price Then select the equivalent working pressure of the hose. If the system is often affected by pressure, it is necessary to increase the working pressure of the hose and choose the hose with higher pulse life. The inner diameter of wear-resistant sand blasting pipe is one of the factors to be considered when selecting rubber hose. The small inner diameter will increase the flow rate of the medium, raise the temperature of the system, reduce the working efficiency, and affect the working performance of the system. The large inner diameter will increase the purchase cost. Therefore, the proper inner diameter should be selected according to the flow rate of the medium. The wear-resistant sand blasting pipe has allowable operating temperature range. The service life and pressure bearing capacity of the rubber pipe can be guaranteed only when it works at an appropriate temperature. When the operating temperature of the equipment exceeds the allowable temperature range of the rubber hose for a long time, special rubber hose shall be purchased or special protective sleeve shall be added on the wear-resistant sand blasting pipe. If the medium to be transported is special, make sure that the hose material is compatible with the medium.