wear-resisting Large diameter suction pipe The inner rubber layer of（ ф 0.3-2.0 reinforcement layer) is the skeleton material that plays the role of reinforcement. What should be paid attention to when storing the wear-resistant sandblasting pipe. 1. The wear-resistant sandblasting pipe should be stored as loose as possible. Generally, rubber hoses with inner diameter less than 76 mm can be wound and stored. 2. During the storage of wear-resistant sand blasting pipe, it is strictly prohibited to stack heavy objects on the pipe body to prevent external extrusion and damage. 3. During the storage of wear-resistant sand blasting pipe, do not contact with acid, alkali, oil, organic solvent or other corrosive liquids and gases, and the heat release should start from 1m away. 4. The storage period of wear-resistant sand blasting pipe shall not exceed 2 years, and it shall be used by the first person to prevent the quality of rubber pipe from being affected by long-term storage. 5. When wear-resistant sand blasting pipes need to be temporarily stored in the open air, the site should be flat and the rubber pipe should be laid flat. The upper cover should be placed under the rubber pipe and no heavy objects should be stacked. At the same time, the hose shall not contact the heat source. 6. The storage place of the upper and lower rubber pipes in the well shall be kept clean and ventilated, and the relative humidity shall be 80. The temperature of the storage place shall be kept between - 15 ℃ and 40 ℃, and the rubber pipe shall be protected from direct sunlight and water spray. 7. When storing wear-resistant sand blasting pipe, Large diameter suction pipe Where can I find it? Both ends of the hose shall be sealed firmly to prevent sundries from entering the hose. 8. When the wear-resistant sand blasting pipe is stored, it should be placed separately according to different varieties and specifications, not mixed, and hang the management board. 9. In order to prevent the pipes from being pressed and deformed during storage, they should not be stacked too high, and the stacking height should not exceed 1.5m. It also requires rubber hoses to be "stacked" frequently during storage, at least once a quarter.

1. The use of protection cannot be ignored: the long-term use of high-pressure sand blasting hose joints at home usually does not cause concern, but excessive use and improper protection also buried the hidden danger of joint cracking to a certain extent. It is understood that the service life of the joint is usually 200000 times, and it should be replaced after long-term use. When using the side, Large diameter suction pipe Where can I find it? Care should be taken to close and open as gently as possible and not to rotate the knob of the hose connector repeatedly. 2. Differentiation of quality can be based on standard evidence collection. It is understood that it is still difficult to determine the cause of joint cracking. At present, the National Bureau of Technology and Quality Supervision has issued recommendations for sealing nozzles and hose specifications. These two specifications perfectly adjust the quality specification target of connectors and hoses. Consumers can go to the quality inspection department to check the torsional strength of the connecting hose, the tightness of the connecting spool and the strength of the connecting materials. If the content of standard rules cannot be met, it will be attributed to quality problems, which can serve as a strong basis for expression. 3. The appearance of hose connector is difficult to distinguish between good and bad. In order to pursue profits and reduce costs, many manufacturers currently use selected cast iron (easy to rust) and zinc alloy (non anti-corrosion) as materials to produce high-pressure sand blasting hose joints, which causes product quality problems. It is understood that the quality of connectors and hoses is not up to standard, Wuxi Large diameter suction pipe The strength function and sealing function of high-pressure sand blasting hose joints are not up to standard due to problems such as materials and wall thickness, which should be paid attention to by consumers.

If conditions permit, secondary vulcanization shall be adopted, wear-resisting Large diameter suction pipe Effectively remove the odor generated during the consumption of odorless hose. Pay attention to the volatilization of various ingredients in the odorless hose formula. When the odorless hose is consumed, in addition to paying special attention to the raw materials and vulcanization process of the reclaimed rubber, pay attention to the selection of various ingredients and whether they will volatilize in the vulcanization process. The volatilization of vulcanizing agent, accelerator and antioxidant will produce a great smell. It is very important to accurately determine the length of the required rubber sand blasting pipe by using the rubber sand blasting pipe. It shall also be checked whether the use conditions of the rubber sand blasting pipe meet the requirements of the selected rubber sand blasting pipe. It should be ensured that the rubber sand blasting pipe you will use is the most suitable one. The working pressure and suction should be carefully determined. Special attention shall be paid to the test standard pressure change or pressure peak of wear-resistant sand blasting pipe. Exceeding the promised maximum value will greatly shorten the service life of the rubber sand blasting pipe. Both ends of the rubber sand blasting pipe cannot be continuously immersed in the transported material. If the bending radius of the rubber sand blasting pipe is less than the minimum value, Wuxi Large diameter suction pipe Its service life will be greatly shortened. Therefore, before installation, it is recommended that you consult the application of information, especially the information about the bending radius of the rubber sand blasting pipe. Protection and cleaning of rubber sand blasting hose: it is recommended to empty the hose after use. Clean if necessary. Inspection: After each use, the rubber sand blasting pipe must be inspected to ensure that it does not show structural damage.

wear-resisting Large diameter suction pipe It will burst for a long time due to frequent and severe pressure shocks. This situation is usually not caused by excessive static pressure, but is related to the strength and frequency of pressure shock. During the operation of construction machinery, the oil pressure in the oil resistant hose will rise or fall repeatedly, and then it will form frequent pressure shocks to the oil pipe, causing the oil seal of each part to become more damaged, the oil resistant hose will bubble and break, and the pipe joint will become loose and leak. Therefore, in the process of operation, the valve rod should not be pulled too hard, and it needs to be gentle. The application temperature of the oil in the oil resistant rubber hose is too high, resulting in aging and bursting of the rubber hose. During the operation of construction machinery, the hydraulic system will cause the oil to become hot due to power failure, and the influence of external temperature (especially in summer) will cause the oil temperature to rise sharply. The higher the oiling temperature is, the easier the rubber hose ages, the worse the elasticity is, the lower the strength and sealing function are, and the oil resistant hose will burst quickly. Therefore, Large diameter suction pipe Where can I find it? During operation, when the temperature rise of the hydraulic system is too high or too fast, the causes should be found and eliminated in time. Necessary cooling measures shall be taken for summer operation, especially continuous operation.

For the woodworking industry, many users wear-resisting Large diameter suction pipe Not unfamiliar, this is an industrial dust collector used on woodworking carving machines, mainly used to absorb wood chips, wood ash, etc. At present, there are many kinds of woodworking vacuum tubes on the market. In the past few years, major furniture factories used PVC steel wire hoses with flat ends. In recent years, more and more enterprises have replaced cheap PVC steel wire hoses with more wear-resistant and durable pu steel wire expansion tubes. Some of the former take a few days or a month, while some of the latter take a few months or a year, They are also steel wire hoses. Why is the service life gap so far? First of all, you may have the impression that many PVC hoses have a very bad smell. This kind of hose is often used in daily life. Because the raw material itself is very cheap, the price of the finished product is also very low. For example, only a dozen yuan a piece. Think about the price of PVC raw materials, which is generally 8-15 yuan a kilogram, And most businesses will not use expensive PVC raw materials, Large diameter suction pipe Where can I find it? The woodworking vacuum tube produced in this way has a very strong smell, not only unpleasant, but also many times the product can not even achieve environmental protection. However, the current updated product, pu steel wire telescopic tube, is a large woodworking furniture factory. An expensive woodworking carving machine uses a cheap vacuum tube with a very smelly smell, which has much to do with the overall style.

Comprehensive evaluation of world conveyor belt wear-resisting Large diameter suction pipe The development level and the application practice of large industrial and mining enterprises in China, in the future, the technology and market development of conveyor belt vulcanizers in China will show the following eight characteristics: more intelligent: Canada Xiaoai Group has recently launched a new X-PAD conveyor belt vulcanizer control system, which uses full touch color screen control, and one operating system can implement real-time monitoring on multiple pairs of vulcanizer heating plates, And it can conduct remote monitoring through WIFI. This system will greatly improve the intelligent control degree of conveyor belt vulcanizer, and undoubtedly represents an important trend in the future development of conveyor belt vulcanizer technology. Higher cost performance: With the improvement of refined management of industrial and mining enterprises, the extensive "stupid and bulky" equipment can no longer adapt to modern production, and the provision of "customized combination" system solutions will become an inevitable choice for future conveyor belt vulcanizer suppliers - conveyor belt vulcanizer is a "tool type" equipment, Suppliers or design units can assist industrial and mining enterprises to comprehensively analyze the belt width, lap length and other use conditions of the conveyor system, and customize the overall solution of the conveyor belt vulcanizer that can be applied to multiple belt joints and maintenance at the same time. So as to effectively reduce procurement costs. More security: in terms of security measures, Large diameter suction pipe Where can I find it? As the leader in the conveyor belt vulcanizing machine industry, Xiao Ai segmented vulcanizing machine can be used as a model: (1) its beam system adopts aviation grade aluminum profile, zhuanliE design, and has a safety window. When it is used, it penetrates the safety bar, and is equipped with a safety pin protection system; (2) International certified cables such as American UL are used to fully ensure the safety and reliability of use. (3) The recently launched new UBR vulcanizing machine pioneered the use of new materials to replace the bolt structure with a strong rope system, and designed a related structure between the new beams, which used the safety protection measures of the vulcanizing machine pressurization system to the extreme.