Whether in the process of purchase or use, wear-resisting Oil resistant hose The quality of all needs to be checked regularly. During the inspection, the following items should be noted. 1. Standard size and actual error of high-pressure rubber hose: because the inner diameter and outer diameter of high-pressure sand blasting pipe and the outer diameter of the skeleton layer will shake, if the shaking amplitude exceeds the allowable limit, the balance of the buckling amount of the sand blasting pipe joint cannot be guaranteed, and the quality of the sand blasting pipe assembly cannot be guaranteed. Therefore, for the sand blasting pipe selected for the production of sand blasting pipe assembly, it is necessary to strictly check whether the inner diameter and outer diameter of the skeleton layer meet the requirements, and the requirements for the outer diameter error can be appropriately relaxed. 2. Wall thickness error of high-pressure hose: due to the local pain of the rubber layer in the high-pressure sandblasting pipe and the influence of the overlapping width of the rubber layer in the high-pressure sandblasting pipe quality inspection center between the skeleton layers, the wall thickness error of the sandblasting pipe may be too large. If the wall thickness error exceeds the allowable range, it will affect the tightness and pull-out strength of the connector, and even cause some deflection (tilting head) of the hose assembly connector. Quality inspection of high-pressure sand blasting pipe Therefore, the wall thickness error of sand blasting pipe should be strictly controlled. Generally, the rubber hose with wall thickness error exceeding 0.5mm shall be selected stably. 3. Adhesion between each layer of high-pressure rubber hose: high-quality high-pressure sand blasting pipe shall have prominent integrity, that is, the quality inspection of high-pressure sand blasting pipe shall have high adhesion between each structural layer, and the adhesion between each adhesive layer shall become an integrity. Only in this way can we meet various technical requirements in the process of joint installation and fastening, and only in this way can we ensure the quality inspection requirements of high-pressure sand blasting pipes for sand blasting pipe assembly. Therefore, Oil resistant hose company It is necessary to control the adhesive force between each layer of the rubber hose not lower than that specified in the technical standard, and the rubber hose with high adhesive force shall be selected as far as possible to produce the rubber hose assembly.

Guizhou Oil resistant hose Vulcanization of technical performance indicators is an important process to enhance the adhesive strength between rubber and reinforcement layer and make it a whole in rubber hose manufacturing, and also an important link to ensure and improve product quality. In order to obtain good pulse performance and service performance of steel wire reinforced rubber hose, in addition to reasonable structure and formula, it is necessary to ensure the compactness of vulcanized hose. In order to meet this performance requirement, the traditional vulcanization method is to wrap the water in water cloth on the semi-finished hose before vulcanization, make braided hose or steel wire for reinforcement and fastening, and vulcanize in batches with steam vulcanization tank. Since the performance requirements of medium and low pressure hoses are low, the rubber hose can also be directly put into the curing tank without fastening. Although water wrapped cloth vulcanization can also increase the compactness of the hose, its appearance is poor. In order to obtain the smooth outer surface of the hose, the lead coating vulcanization method is widely used at home and abroad. For decades, people have been using this method as an effective method to vulcanize and strengthen rubber hoses, especially high-pressure rubber hoses. So far, many domestic and foreign manufacturers are still using this method to produce rubber hoses. But the fatal disadvantage of this method is that it pollutes the environment. Oil resistant hose company The main control function of the air compressor station unit is to exhaust more air. According to different structures, it can be divided into full hose, cloth hose, steel braided hose, etc. According to different uses, it can be divided into air hose, water suction hose, water delivery hose, heat resistant hose, acid (alkali) resistant hose, oil resistant hose and special hose., It can be closed within the specified range.

Guizhou Oil resistant hose The break of the sandblasting hose usually refers to the appearance and change of the crack of the sandblasting hose. The sandblasting hose has one or more cracks, but the cracks are neat. Another is that the internal bending cracks at the crack of the sandblasting hose are neat. The causes of different errors are different, and the treatment methods are also different. Therefore, in the process of using or protecting the sandblasting hose, the sandblasting hose should not be subject to changing torque. When installing the sandblasting hose, try to keep the axis of the two joints on the same plane to avoid twisting the sandblasting hose in use. Therefore, be careful with the application, and try not to make the sandblasting hose change excessively to avoid consumption. Sand blasting hose plays a very important role in the industry. Its inner rubber layer is added with carbon black, which can effectively eliminate static electricity and directly contact with compressed air and abrasives. The requirement for wear resistance is quite high. Once worn through, the reinforcement layer will be exposed, and the sand blasting hose will burst. The reinforcing layer of sandblasting hose is a pressure resistant layer, so wear-resisting Oil resistant hose The material and layout of the reinforcement layer directly determine the pressure rating of the sandblasting hose. There are two common enhancement layers: cloth clip enhancement layer and surround enhancement layer. The sand blasting hose with an inner diameter of 50mm or more is mostly used in the construction occasions where the sand blasting pipe needs to be extended to reduce the pressure loss in the sand blasting hose and ensure the normal operation of shot blasting.

With the development of modern industry, the demand for high temperature and high pressure sandblasting hoses is growing, Oil resistant hose company Scope of application: completely flexible conveying pipe is required to prevent the pipe from being in vibration position. It is suitable for steam, gas, air, heavy oil, petroleum, chemical industry, etc. First of all, the structure of fire sprinkler metal sandblasting hose (explosion-proof pipe) must have compulsory knowledge. Fire sprinkler metal sandblasting hose (hereinafter referred to as explosion-proof pipe) is a high-quality sandblasting hose in modern industrial pipelines. It is mainly composed of fire sprinkler metal sandblasting hose bellows, fire sprinkler metal sandblasting hose net sleeve and fire sprinkler metal sandblasting hose connector. The inner pipe is a thin-walled stainless steel fire sprinkler metal sandblasting hose corrugated pipe with spiral or circular waveform. The outer layer of the fire sprinkler metal sandblasting hose corrugated pipe is woven by stainless steel wire or steel strip according to certain parameters. The fire spraying metal sand blasting hose connector or flange at both ends of the sand blasting hose shall match with the fire spraying metal sand blasting hose connector or flange of the user's pipeline. wear-resisting Oil resistant hose Scope of application of fire sprinkler metal sandblasting hose (explosion-proof pipe): full flexible conveying pipe is required in vibration places to prevent pipes, which is applicable to steam, gas, air, heavy oil, petroleum, chemical industry, etc. The annular flame spraying metal sandblasting hose bellows is a special geometric pipe. The outer edges of several annular diaphragms are tangent to several concave half rings facing the center, and the inner edges are tangent to several concave half rings of the vest. Its blanks are mainly made of tubes. The fire sprinkler metal sandblasting hose bellows has the characteristics of large flexibility, good elasticity, simple manufacturing and small rigidity.