production Sandblasting hose The inner rubber layer of（ ф 0.3-2.0 reinforcement layer) is the skeleton material that plays the role of reinforcement. What should be paid attention to when storing the wear-resistant sandblasting pipe. 1. The wear-resistant sandblasting pipe should be stored as loose as possible. Generally, rubber hoses with inner diameter less than 76 mm can be wound and stored. 2. During the storage of wear-resistant sand blasting pipe, it is strictly prohibited to stack heavy objects on the pipe body to prevent external extrusion and damage. 3. During the storage of wear-resistant sand blasting pipe, do not contact with acid, alkali, oil, organic solvent or other corrosive liquids and gases, and the heat release should start from 1m away. 4. The storage period of wear-resistant sand blasting pipe shall not exceed 2 years, and it shall be used by the first person to prevent the quality of rubber pipe from being affected by long-term storage. 5. When wear-resistant sand blasting pipes need to be temporarily stored in the open air, the site should be flat and the rubber pipe should be laid flat. The upper cover should be placed under the rubber pipe and no heavy objects should be stacked. At the same time, the hose shall not contact the heat source. 6. The storage place of the upper and lower rubber pipes in the well shall be kept clean and ventilated, and the relative humidity shall be 80. The temperature of the storage place shall be kept between - 15 ℃ and 40 ℃, and the rubber pipe shall be protected from direct sunlight and water spray. 7. When storing wear-resistant sand blasting pipe, Sandblasting hose company Both ends of the hose shall be sealed firmly to prevent sundries from entering the hose. 8. When the wear-resistant sand blasting pipe is stored, it should be placed separately according to different varieties and specifications, not mixed, and hang the management board. 9. In order to prevent the pipes from being pressed and deformed during storage, they should not be stacked too high, and the stacking height should not exceed 1.5m. It also requires rubber hoses to be "stacked" frequently during storage, at least once a quarter.

I, production Sandblasting hose Quantitative display of quality. In the evaluation plan prepared by the Ministry of Health and Social Insurance for the medical and health system, some indicators were put forward for the service quality of the hospital, such as the number of deaths before and after the operation, the number of unplanned rehospitalization, the infection rate of patients in the hospital, and the immunization rate. It can be seen that the quantification of quality is to reflect the quality of things through a series of quantitative analysis and synthesis. Sand blasting hose enterprises use public opinion polls to measure benefits and service quality. Since the purpose of administrative activities is to meet the needs of society or the public, the best way to measure the social effect and quality is to face the service objects, understand their evaluation and their satisfaction. Although popular, public opinion polls also have limitations, such as high cost, which is difficult to be accurate and reliable due to the influence of public judgment. In addition, the satisfaction of beneficiaries does not answer the question - is this service provided to those who need it most? III, Sandblasting hose company Administrative departments and public service institutions with single business nature. For those departments that have applied the quality assurance system, their performance evaluation only pays attention to efficiency and economy.

Whether in the process of purchase or use, production Sandblasting hose The quality of all needs to be checked regularly. During the inspection, the following items should be noted. 1. Standard size and actual error of high-pressure rubber hose: because the inner diameter and outer diameter of high-pressure sand blasting pipe and the outer diameter of the skeleton layer will shake, if the shaking amplitude exceeds the allowable limit, the balance of the buckling amount of the sand blasting pipe joint cannot be guaranteed, and the quality of the sand blasting pipe assembly cannot be guaranteed. Therefore, for the sand blasting pipe selected for the production of sand blasting pipe assembly, it is necessary to strictly check whether the inner diameter and outer diameter of the skeleton layer meet the requirements, and the requirements for the outer diameter error can be appropriately relaxed. 2. Wall thickness error of high-pressure hose: due to the local pain of the rubber layer in the high-pressure sandblasting pipe and the influence of the overlapping width of the rubber layer in the high-pressure sandblasting pipe quality inspection center between the skeleton layers, the wall thickness error of the sandblasting pipe may be too large. If the wall thickness error exceeds the allowable range, it will affect the tightness and pull-out strength of the connector, and even cause some deflection (tilting head) of the hose assembly connector. Quality inspection of high-pressure sand blasting pipe Therefore, the wall thickness error of sand blasting pipe should be strictly controlled. Generally, the rubber hose with wall thickness error exceeding 0.5mm shall be selected stably. 3. Adhesion between each layer of high-pressure rubber hose: high-quality high-pressure sand blasting pipe shall have prominent integrity, that is, the quality inspection of high-pressure sand blasting pipe shall have high adhesion between each structural layer, and the adhesion between each adhesive layer shall become an integrity. Only in this way can we meet various technical requirements in the process of joint installation and fastening, and only in this way can we ensure the quality inspection requirements of high-pressure sand blasting pipes for sand blasting pipe assembly. Therefore, Sandblasting hose company It is necessary to control the adhesive force between each layer of the rubber hose not lower than that specified in the technical standard, and the rubber hose with high adhesive force shall be selected as far as possible to produce the rubber hose assembly.

1. Mutual wear of rubber lining plate and steel ball of ball mill: both the rubber lining plate and steel ball of ball mill are vulnerable parts. During grinding, the steel ball and material of ball mill do throw line falling movement in the barrel Changchun Sandblasting hose It will collide with steel balls and materials and cause friction. In continuous operation, the rubber lining plate and steel ball of ball mill will be severely worn, which is directly related to the hardness of materials. The greater the hardness of the material, the faster the abrasion speed of the rubber lining plate and steel ball of the ball mill, which may cause equipment damage or even safety accidents in serious cases. In addition, it is also related to the ball of the ball mill. The size and quantity of the ball will affect the service life of the rubber lining plate of the ball mill. If the ball mill is in operation, increasing the amount of steel balls or filling steel balls with larger diameters will increase the wear of the rubber lining plate of the ball mill. 2. The heat treatment process of the rubber lining plate of the ball mill is unreasonable: the unreasonable heat treatment of the rubber lining plate of the ball mill will not only increase the wear of the lining plate, but also affect the yield strength of the lining plate, resulting in the fracture of the bolt of the ball mill under the large shear force. In the actual operation, the staff lacked the understanding of the lining plate material and the heat treatment processing of the ball mill rubber lining plate was insufficient, so the strengthening effect of the ball mill rubber lining plate was not in place and the strength was low. When impacted by steel balls and materials, Sandblasting hose company Plastic deformation often occurs. 3. The material of the rubber lining plate of the ball mill is unreasonable: the material of the rubber lining plate of the ball mill and its heat treatment process are the key to determine the mechanical performance of the lining plate. If the material of the lining plate is not properly selected, its fatigue strength and life will be greatly reduced, which will not meet the requirements of the ball mill, or even plastic deformation or bulge will occur.

production Sandblasting hose It is characterized by high pressure, fire resistance, heat insulation, beautiful pipe body, corrosion resistance, anti-static, high wear resistance, light weight, high and low temperature resistance, good low-temperature bending performance, and long service life. Use: oilfield well control operation, metal smelting, chemical industry, etc. High temperature environment with heat source or thermal radiation. Hydraulic control pipeline of BOP for oil exploration and drilling. High pressure flame-retardant sand blasting pipe is mainly used for hydraulic transmission, medium transmission or power transmission under high-pressure, flammable and high-temperature environment. This product has been widely used in petroleum, chemical, marine, metallurgical and other industries. Flame retardant and fire-resistant: structure: take high temperature and high pressure steel wire winding hose as the base, and the outer skin is covered with nano fire-resistant coating, stainless steel wire braid and flame retardant layer. Hydraulic pipes in high-temperature environment near open fire, such as metallurgical industry, steelmaking, blast furnace, open hearth furnace, etc. Main Uses Hydraulic transmission is widely used in petroleum, chemical, marine transportation media or power transmission under high-pressure, flammable and high-temperature environments. Our products flame retardant sand blasting pipes are characterized by high pressure resistance, fire resistance, heat insulation, oil resistance, acid and alkali resistance. Sandblasting hose company When used in oil drilling well control system, it is superior to ordinary hard pipes, safe and reliable, easy to install and disassemble, time-saving, labor-saving, corrosion resistant, maintenance free, and long service life. Fire resistance: it can work for 15 minutes at 750 ℃. Oil resistance: Immerse in hydraulic oil at 40 ℃ - 100 ℃ for 24 hours without deterioration or falling off.