In the shipbuilding industry, radio industry, electrical industry, telecommunications industry, instrument industry, aviation industry, medical industry, etc., we often see acid and alkali resistant hose, then what is Anshan Suction pipe What about? If you want to know more, please read down! Acid and alkali resistant silicone hose is a kind of pipe specially used for power equipment, which uses acid and alkali resistant silica gel as the main raw material and tightly wraps the pipe wall with electrical grade polyethylene spiral wire. Due to the chemical inertia of acid and alkali resistant silica gel, this kind of pipe has good acid and alkali resistance performance and electrical performance, and is commonly used in the production of wires, cables and lead wires in extreme acid and alkali environments. Also called: acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose, acid and alkali resistant silicone rubber hose. Features: 1. High temperature resistance (250-300 ℃) and low temperature resistance (- 40-60 ℃); 2. Good acid and alkali resistance. Physiologically stable, able to withstand repeated harsh and disinfection conditions, resistant to ozone aging, light aging, weather aging and ultraviolet radiation. 3. Small resilience and permanent deformation (no more than 50% at 200 ℃ for 48 hours), breakdown voltage (20-25KV/mm), ozone resistance and UV resistance. Suction pipe Where can I find it? Radiation resistance and other characteristics, 4. Good electrical performance, small change when exposed to moisture, water or temperature rise, even if the silica generated by short circuit combustion is still an insulator, which ensures that electrical equipment continues to work, so it is most suitable for making wires, cables and lead wires.
Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Anshan Suction pipe It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Suction pipe Where can I find it? The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.
one Anshan Suction pipe When using, the talcum powder on the inner wall of the hose must be blown clean to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with acids, alkalis, oils and other organic solvents that can damage the hose. The storage temperature shall be - 15~40 ℃, and the distance from the heat source shall not be less than 1m. 3. According to the national standards, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; The acetylene hose is black, the working pressure vessel is 0.3MPa, the inner diameter of the hose is 8mm, and the outer diameter is 16mm. 4. The gas cutting operation requires a large oxygen output, so the valves of the gas cylinder (or oxygen pipeline) connected to the high pressure end of the oxygen meter should be fully opened to ensure adequate flow and stable pressure. The low pressure gauge has indicated the working pressure, but the pressure drops suddenly when using oxygen. At this time, it is easy to backfire and may backfire into the oxygen hose to cause explosion. 5. Oxygen hose and acetylene hose shall not be mixed or substituted with each other, and oxygen and hose shall not be used to blow away the blockage of acetylene hose. At the same time, it is necessary to check and eliminate the defects such as gas leakage and blockage of the welding torch at any time to prevent the formation of oxygen and acetylene mixture in the hose. It should be pointed out that the hose color specified in the national standard is opposite to that specified in the international standard (ISO) (oxygen hose is black, acetylene hose is red). At the same time, it is different from the original ministerial standard (HG4-605-66) that oxygen hose is red and acetylene hose is green. Before 1966, domestic oxygen hose was black or green and acetylene hose was red. thus Suction pipe Where can I find it? It causes inconsistency between the understanding and habits of the supply department and the user, and is easy to cause accidents due to the mixing and substitution of rubber hoses. At present, it should be emphasized that unified understanding and use should be carried out in accordance with the provisions of national standards, and attention should be paid to distinguishing the rubber hoses of imported equipment.
Anshan high quality Suction pipe Plays an important role. In the application of different industries, according to their own needs, check the performance of the products, give proper play to the advantages of the products, and ensure the normal use of daily applications. When replacing the wear-resistant sand blasting pipe, the length of the rubber pipe, the number of steel wire layers, the shape and size of the joint should be reasonable, and the curvature of the rubber pipe should be minimized. When tightening the connecting nuts, do not tighten the rubber hose. Excessive bending and twisting will greatly reduce the service life of the rubber hose. Protective measures shall be taken for the parts liable to friction to prevent the rubber hose from bursting due to wear. What should we pay attention to when purchasing wear-resistant sandblasting pipe? Different types of wear-resistant sand blasting pipes have different working pressures. When purchasing rubber hose, you should first determine the working pressure of the system, Suction pipe Where can I find it? Then select the equivalent working pressure of the hose. If the system is often affected by pressure, it is necessary to increase the working pressure of the hose and choose the hose with higher pulse life. The inner diameter of wear-resistant sand blasting pipe is one of the factors to be considered when selecting rubber hose. The small inner diameter will increase the flow rate of the medium, raise the temperature of the system, reduce the working efficiency, and affect the working performance of the system. The large inner diameter will increase the purchase cost. Therefore, the proper inner diameter should be selected according to the flow rate of the medium. The wear-resistant sand blasting pipe has allowable operating temperature range. The service life and pressure bearing capacity of the rubber pipe can be guaranteed only when it works at an appropriate temperature. When the operating temperature of the equipment exceeds the allowable temperature range of the rubber hose for a long time, special rubber hose shall be purchased or special protective sleeve shall be added on the wear-resistant sand blasting pipe. If the medium to be transported is special, make sure that the hose material is compatible with the medium.
Anshan Suction pipe It is composed of sand blasting hose, net sleeve and joint. The sand blasting hose is the main body of the rubber sand blasting pipe, playing a flexible role, and the net plays a role of strengthening and shielding; Joints play the role of connection. For different use requirements, they are connected in different ways: sandblasting hose, net sleeve and joint are connected by welding, which is called welding type; The connection in the form of mechanical clamping is called mechanical clamping. In addition, the combination of the above two methods is called hybrid clamping. Rubber sand blasting pipe products include oil suction hose, steam hose, sand blasting hose, acid and alkali suction hose, food hose, oxygen blowing hose and various special-shaped hoses. It is widely used in machinery, chemical industry, petroleum, metallurgy, food and other industries. What is the pressure range of pressure resistant rubber sand blasting pipe: the pressure range of hose is generally Pn 0.6-32.0 MPa. The rubber sand blasting pipe up to 42.0 MPa is the main pressure bearing part of the hose installed in the pressure pipe, and it acts as the sheath of the sand blasting hose. Suction pipe Where can I find it? One or more layers of stainless steel wire or steel strip can be selected for braiding according to the pressure in the pipeline and the place of use. It can also achieve the effect of reducing noise. This is why some rubber sand blasting pipes use rubber sand blasting pipes.
