Xining Cord hose Vulcanization of technical performance indicators is an important process to enhance the adhesive strength between rubber and reinforcement layer and make it a whole in rubber hose manufacturing, and also an important link to ensure and improve product quality. In order to obtain good pulse performance and service performance of steel wire reinforced rubber hose, in addition to reasonable structure and formula, it is necessary to ensure the compactness of vulcanized hose. In order to meet this performance requirement, the traditional vulcanization method is to wrap the water in water cloth on the semi-finished hose before vulcanization, make braided hose or steel wire for reinforcement and fastening, and vulcanize in batches with steam vulcanization tank. Since the performance requirements of medium and low pressure hoses are low, the rubber hose can also be directly put into the curing tank without fastening. Although water wrapped cloth vulcanization can also increase the compactness of the hose, its appearance is poor. In order to obtain the smooth outer surface of the hose, the lead coating vulcanization method is widely used at home and abroad. For decades, people have been using this method as an effective method to vulcanize and strengthen rubber hoses, especially high-pressure rubber hoses. So far, many domestic and foreign manufacturers are still using this method to produce rubber hoses. But the fatal disadvantage of this method is that it pollutes the environment. Cord hose company The main control function of the air compressor station unit is to exhaust more air. According to different structures, it can be divided into full hose, cloth hose, steel braided hose, etc. According to different uses, it can be divided into air hose, water suction hose, water delivery hose, heat resistant hose, acid (alkali) resistant hose, oil resistant hose and special hose., It can be closed within the specified range.

Cord hose company The following recommendations contain a series of precautions to prevent items from aging to a greater extent during storage. 1. During storage, the rotating plan system shall be adopted to shorten the storage time of high-pressure braided hose as much as possible. If long-term storage cannot be avoided and the following recommendations cannot be followed, high-pressure braided hoses should be thoroughly inspected before use. 2. Physical storage conditions: The high-pressure braided hose must be stored without mechanical pressure, including excessive stretching, compression or deformation, and without contact with sharp or sharp objects. High pressure braided hoses should be stored on suitable supports or on dry ground. High pressure braided rubber tubes packaged as coils must be stored horizontally. High pressure braided rubber pipes shall not be stacked. If stacking cannot be avoided, the stacking height shall not cause permanent deformation of the high-pressure braided rubber pipe below. Pumping high-pressure hydraulic hose is a common high-pressure hydraulic hose. In order to ensure the operation safety of the pumped high-pressure hydraulic hose, the following small series will briefly introduce the correct use of the pumped high-pressure hydraulic hose: 1. Before each use of the high-pressure hydraulic hose, the surface of the high-pressure hydraulic hose must be evenly coated with soap liquid, which can play a non bonding role between the high-pressure hydraulic hose and the concrete, and play a lubricating role in the drawing process, It can greatly increase the reuse times of high-pressure hydraulic hoses. 2. Installation: first, insert the steel hinge wire into the inner hole of the draw tube to avoid extrusion deformation when pouring concrete. Then, pull out the high-pressure hydraulic hose coated with soap liquid from the prestressed hole and fix it in the correct position with a fixing ring. The spacing of the retaining rings is controlled by the suspension and is usually about 500 mm. wear-resisting Cord hose When connecting the high-pressure hydraulic hose, wrap both ends of the high-pressure hydraulic hose for one and a half weeks or two weeks with thin iron sheet or PVC pipe (vertical cutting), fix them with iron wire, and then seal both ends of the PVC pipe with tape to avoid entering the mortar.

We all know Cord hose company The noise pollution in industrial production is very serious, and noise pollution is also an important factor affecting workers' enthusiasm for production. Ball mills were once a major source of noise in mining equipment. In order to reduce the noise generated by ball mills, protect the physical and mental health of workers, improve workers' enthusiasm for production, and create greater profits for the company, Through the efforts and research of domestic and foreign industry experts, the ball mill liner has been transformed. Through repeated tests and comparison, it is found that the noise generated by the rubber liner and the manganese steel liner of the ball mill is far less than the manganese steel liner when the technical parameters are up to standard. According to the data provided by the noise monitoring station and the concentrator, We analyzed the noise intensity and the economic benefits: the domestic ND2 precision sound level meter and octave filter were used for detection, and the sound level meter was calibrated by the provincial sound level meter measurement and verification station; There is no sound insulation room in the ball mill workshop. The monitoring points are arranged according to the position of the ball mill and the flow of workers to observe the mechanical operation, 2m away from the sound source. One monitoring point is respectively set on the left and right of the east and west of the workshop and in the middle of the two ball mills. The measurement method is in accordance with the Noise Detection Specification for Industrial Enterprises. As the noise in the workshop is continuous and steady, sound level A is used as the evaluation basis. The rubber lining plate is manufactured by Hainan Rubber Lining Plate Factory according to the ball mill shell structure and the original manganese steel lining plate specification (1.4mx0.74mX0.07m). Xining Cord hose First, take out the manganese steel lining plate in the ball mill barrel, and then install the rubber lining plate in the barrel in turn (front and back). Each ball mill is installed with 48 pieces. First, use the pressure strip to compress, and then use the screws to fix the rubber lining plate on the ball mill barrel, so as to prevent falling off when rotating. The noise intensity of the ball mill workshop with manganese steel liner is 94-103dB (A), while the noise intensity of the ball mill workshop with rubber liner is 87-92dB (A), and the noise reduction difference is 7-11dB (A). The rubber liner has good noise reduction effect.

Xining Cord hose The break of the sandblasting hose usually refers to the appearance and change of the crack of the sandblasting hose. The sandblasting hose has one or more cracks, but the cracks are neat. Another is that the internal bending cracks at the crack of the sandblasting hose are neat. The causes of different errors are different, and the treatment methods are also different. Therefore, in the process of using or protecting the sandblasting hose, the sandblasting hose should not be subject to changing torque. When installing the sandblasting hose, try to keep the axis of the two joints on the same plane to avoid twisting the sandblasting hose in use. Therefore, be careful with the application, and try not to make the sandblasting hose change excessively to avoid consumption. Sand blasting hose plays a very important role in the industry. Its inner rubber layer is added with carbon black, which can effectively eliminate static electricity and directly contact with compressed air and abrasives. The requirement for wear resistance is quite high. Once worn through, the reinforcement layer will be exposed, and the sand blasting hose will burst. The reinforcing layer of sandblasting hose is a pressure resistant layer, so wear-resisting Cord hose The material and layout of the reinforcement layer directly determine the pressure rating of the sandblasting hose. There are two common enhancement layers: cloth clip enhancement layer and surround enhancement layer. The sand blasting hose with an inner diameter of 50mm or more is mostly used in the construction occasions where the sand blasting pipe needs to be extended to reduce the pressure loss in the sand blasting hose and ensure the normal operation of shot blasting.

Xining Cord hose It is mainly used for the transportation of liquid and gas. The use requirements of cloth clip sand blasting pipe are stricter than those of ordinary rubber hose. The so-called high voltage puts forward this requirement. The following small series will introduce the use requirements of cloth clip sandblasting pipe. According to the use characteristics of cloth clip sand blasting pipe, the larger working pressure of cloth clip sand blasting pipe is determined according to the system pressure. Each cloth clamping sand blasting pipe has a normal working pressure, and the bursting pressure of cloth clamping sand blasting pipe is 3-4 times of the larger working pressure. The higher the pressure, the higher the number of steel wire layers, and the more stringent the product production. Therefore, according to the actual pressure of the system, the higher the working pressure of the cloth clamping sand blasting pipe, the normal operation of the system can be ensured, and the appropriate cloth clamping sand blasting pipe can be selected. If the impact pressure of the system is frequent, the cloth clip sandblasting pipe with high pulse life shall be selected, and the specification and model classification of the cloth clip sandblasting pipe shall be properly improved. Temperature is also one of the factors considered by customers. Cord hose company The high and low temperature transition in the working environment will affect the service life and pressure bearing capacity of the rubber hose. Therefore, high-pressure rubber hoses should be used within their allowable range. For the system whose long-term operating temperature is not within its allowable range, hose sheath or special rubber hose shall be purchased.