Cord hose Price It has become the standard configuration of the modern new ball mill, but many problems may occur during the use or installation of the rubber lining plate, which will cause the failure of the rubber lining plate of the ball mill. Here is a brief introduction to the causes of the more common failure of the rubber lining plate of the ball mill. The design and installation are not professional and reasonable. The design and installation are also common problems for many novice manufacturers. For example, the bolt holes for fixing the ball mill lining plate are square, which will cause stress concentration and fracture. Adjust the size of lining plate to control the gap between lining plates at about 8mm; The installation quality of lining plate is very important to the safe operation of ball mill. First, tighten the fixed wedge symmetrically, put the lining plate in sequence, and then use the tightening wedge to secure it; Therefore, professional installation guidance can easily avoid these problems. The reason why the rubber lining plate of the ball mill does not match the steel ball is relatively common, and it is easy for many novice manufacturers to ignore and make mistakes. During the operation of the ball mill, the rubber lining plate of the ball mill, materials and steel balls promote the normal grinding and crushing of the ball mill due to the interaction of forces. The hardness of materials is related to wear resistance, and the wear resistance increases with the increase of hardness, Kunming Cord hose It is a pair of friction pairs, and the increase of hardness of one side will cause the wear of the other side to increase. Therefore, the high wear-resistant rubber lining plate is matched with the high wear-resistant steel ball, and the low wear-resistant rubber lining plate is matched with the low wear-resistant steel ball, so as to ensure the normal wear of the rubber lining plate of the ball mill and extend the service life of the ball mill.

What is stainless steel spiral duct? Cord hose Price The products are mainly used to connect the air flow between two places and play the role of ventilation. There are three types of galvanized spiral air ducts, stainless steel spiral air ducts and composite spiral air ducts. Here we mainly talk about the stainless steel spiral air duct, and briefly analyze the reason why it is widely used in villas. The so-called stainless steel air duct is strictly a kind of air duct processing technology, also known as spiral seamed thin-walled tube. The best quality is the thin-walled tube with spiral seamed made of metal strips. Because the applied material is metal, it is also called spiral seamed metal tube. It was first used in the military industry of western countries, such as ships, ship ventilation, air conditioning systems, and later used in trains Subway, mine and other civil facilities. By 2000, according to statistics, 95.6% of office buildings, shopping malls and subways in the United States had applied spiral air ducts. In civil residential buildings, 72.5% of central air conditioners use spiral air ducts. Since the mid-1990s, China has introduced this technology into the shipbuilding industry. With the rapid development of China's economy, the use of central air conditioners has increased year by year, and the quality of auxiliary products for exhaust and air supply has been continuously improved. Spiral air ducts have been widely used in some villas. (1) Product standardization: The production of spiral round air duct fittings (pipe fittings and joints) has been highly automated, systematic, and has industrialized quality control. It is well known that the wind resistance of circular duct is much smaller than that of rectangular duct. (2) Easy to install. The installation of spiral air duct significantly reduces the connection points between pipes and minimizes the leakage at the joint of pipe fittings. The typical spiral air duct is 3~6m long, while the typical rectangular air duct is only 1~1.5m long; The connection of two spiral air ducts requires only one pipe connector, while the connection of traditional rectangular air ducts often requires a completely independent double flange system. (3) Usually only small installation space is required: the same wear-resisting Cord hose The circular pipe with a diameter of 200mm in the installation space can replace 250 × 150mm rectangular pipe. On the premise of not increasing additional installation space, several parallel circular pipes can replace flat rectangular pipes.

Many people have never understood wear-resisting Cord hose It is better to use cast iron or rubber lining plate, so today I will give you a detailed analysis. The lining plate of the ball mill can tell you for sure that it is better to use rubber lining plate, which is also a trend for rubber lining plate to replace manganese steel lining plate. The rubber lining plate has many advantages that can not be achieved by manganese steel lining plates such as cast iron, so it has more advantages. One of the advantages of using cast iron or rubber liner for ball mill liner is that the noise of rubber liner is lower. In the process of grinding the rubber lining plate with materials, the noise is lower because it is not directly rubbed. Moreover, the rubber lining plate can throw the steel ball up for the second time to form the second grinding of materials, which makes the grinding of materials more thorough and the grinding fineness more uniform with good effect. In addition, the rubber lining plate can reduce the noise by an average of 30 dB compared with the noise of the cast iron lining plate, making it acceptable. Another important reason is energy saving. Energy consumption is an unavoidable problem for users of ball mills, because the cast iron lining plate is heavy in quality, Cord hose Price Therefore, when the motor drives the lining plate, it will consume a lot of power. The rubber used by the rubber lining plate itself is light, so the electric energy consumed by the motor when driving is very small, which can be more than 10000 yuan of electric energy a year.

wear-resisting Cord hose The thickness of the seaming plate shall be within the regular range of products of various specifications. If it is less than the thickness, cracks, wrinkles and other defects are likely to occur during seaming; If it is larger than the large thickness, as the square of the plate thickness is proportional, the bending force will significantly increase, which will cause abnormal damage to the forming roller, overloading of the transmission system, and stuffiness. In dust removal system: galvanized air duct can be used for collection and transportation of dust removal device. In the oil smoke exhaust system: there are a lot of oil smoke in restaurants, restaurants and hotel kitchens, which need to be discharged. The galvanized air duct is suitable, strong, economical and practical. In air conditioning system: galvanized air duct can be pasted with thermal insulation materials inside, and the surface is beautiful. In bulk material transportation: pneumatic transportation system, some finer and looser material particles can be transported by galvanized air ducts, with low cost and good effect. In the ventilation system: supply fresh air and exhaust gas, exhaust harmful gas outdoors, and send outdoor fresh air indoors. The strength of stainless steel plate shall be higher than that of ordinary steel plate. Before seaming with stainless steel plate, forming test shall be carried out first to avoid overloading the equipment and causing excessive wear or mechanical trouble. Due to the poor plasticity of the aluminum plate, it is easy to crack during the forming of the seaming. The forming test should also be carried out before construction. At the same time, because the aluminum plate is lack of elasticity, the aluminum plate air duct cannot be subject to snap seaming. After the zinc coating of galvanized air duct is passivated, dyed or coated with light protection agent, Cord hose Price It can obviously improve its protection and decoration. The fireproof function of galvanized air duct is mainly reflected in that it is incombustible, but one thing needs to be noted is that whether its insulation layer is burned depends on the material. We suggest that the galvanized air duct should be made of incombustible insulation materials such as centrifugal glass wool.