What are the process requirements for making welded air ducts? Both ends of the expansion joint are welded to the outer wall of the air duct. production Suction pipe When the fan coil unit is equipped with two air outlets, the double-layer shutter with regulating valve should be selected. Usually only small installation space is required. Without increasing any pressure drop, a circular pipe with a diameter of 200mm in the same installation space can replace 250 × 150mm rectangular pipe. Features: The iron sheet is prone to chemical reaction in various environments, causing corrosion and rust. However, zinc hardly changes in dry air. The thermal insulation and fire resistance performance indicators of the welded air duct system shall meet the requirements of Code for Acceptance of Construction Quality of Ventilation and Air Conditioning Engineering (GB50243) and Technical Specification for Ventilation Ducts (JGJ141) respectively. In the ventilation system: supply fresh air and exhaust gas, exhaust harmful gas outdoors, and send outdoor fresh air indoors. This technology is widely used in various process pipelines, oil and gas pipelines in oil fields and other cleaning projects. Especially for pipeline cleaning of long-distance fluid transportation, it has advantages that cannot be replaced by other technologies. When the air leakage rate exceeds the requirements of the design and acceptance specifications, the leakage can be detected by listening, touching, observing, water or smoke, and the air leakage position can be found and marked; After repair, retest until qualified. Safety seal ring leak proof system. The exquisite spiral pressing rib technology enables the spiral air duct to have good strength under pressure, Suction pipe Where can I find it? With the addition of spiral ribs, the thickness of the seam is four times that of the pipe body. The rigidity of the pipe is very large, which shows the advantages of firmness. It can withstand large pressure loads without damaging deformation. The thickness of materials can be reduced by 15%, reducing costs.

Suction pipe Where can I find it? Precautions ① The acid and alkali resistant rubber hose used shall not only be oil resistant, but also be pressure resistant, heat resistant, cold resistant, wear resistant and aging resistant. ② The rubber hose should not be too long or too short, generally 1.4 meters. ③ The interface is tight and can be fastened with thin iron wire or clip to prevent falling off and air leakage. ④ It is forbidden to pull acid and alkali resistant rubber hose from one room to another or through walls, floors and floors to prevent accidents caused by rubber hose breaking and falling off. ⑤) The acid and alkali resistant rubber hose should be placed in a place where it can be seen frequently, so that it is easy to detect leakage. Check whether the rubber hose leaks after each bottle change. ⑥ Do not replace acid and alkali resistant rubber hose with universal rubber hose. Since the full rubber hose does not contain a skeleton layer, it is only necessary to use a press out machine to press out the hose; The cloth clamping hose needs to use a molding machine that wraps the adhesive tape on the inner adhesive layer; When forming the suction hose, first wrap the metal spiral wire and then wrap the inner rubber; Special fabric knitting machine or winding machine shall be used for knitting and winding hose; Knitting machine is required for knitting hose. Sichuan Suction pipe The basic production processes include rubber mix processing, cord fabric and canvas processing, rubber tube molding, vulcanization, etc. The acid and alkali resistant hose manufacturer said that the processing method of the skeleton layer and the hose molding equipment are different for different structures and different skeletons.

Sichuan Suction pipe It is a kind of hose that can be used for sand pumping and sand suction produced with high abrasion resistant rubber. It is often used in sand blasting industry, cement, steel, minerals and other industries, but it is mainly used in river dredging, slurry transportation in mines, sand digging and sand taking and other industries to transport sharp granular solids or solid-liquid mixtures. Its product structure is composed of high wear-resistant layer, reinforced water pipe layer, skeleton steel wire and outer rubber. Today, Myers will introduce the application field of wear-resistant sand absorption rubber pipe. When the wear-resistant sand suction rubber pipe is applied in the mine pit, it is necessary to set a floating boat equipped with a sand pump in the mine pit, and use the floating sand suction rubber pipe to connect with the sand pump. The floating boat will float up and down with the rise and fall of the water level. It is required that the pipe body has good flexibility and good tear resistance and bending resistance. The offshore pipeline is connected by non floating sand suction hose until the pulp transportation destination. The overall pipeline is divided into two parts, one for surface use and the other for onshore use. The main raw material of these two kinds of hoses is high abrasion and corrosion resistant rubber, and cord reinforcement layer and steel wire skeleton layer are added in the pipe wall to ensure the pressure resistance and tear resistance of the hose. The connection mode is vulcanized flange connection, that is, the flange and the hose are a whole, so there is no need to worry about the flange falling off. Floating sand suction hose used on the water surface. This kind of hose is required to float on the water surface. Due to the large drop of the mine (100 meters) and the long conveying distance Suction pipe Where can I find it? The hose shall have high pressure resistance, and the design pressure is 25 kg/cm2 according to the calculation. It should be considered that the floating ship will move up and down with the rise and fall of the water level and the wave will cause lateral displacement. Its internal structure is the same as the sand suction hose used offshore, except that a floating body is installed outside the hose.

production Suction pipe Or PVC steel wire spiral reinforced pipe. The commodity is made of high-quality PVC plastic raw materials. PVC steel wire reinforced pipe is also a PVC steel wire reinforced hose that uses steel wire reinforcement. The embedded spiral steel wire is used as the reinforcement layer, so the product has both rigidity and flexibility, that is, it has both satisfying mechanical properties and rigidity, and excellent flexibility. The reinforced pipe of latex fiber is PVC hose embedded with steel wire framework. The inner and outer tube walls are clear, lubricated, free of bubbles, and the fluid transportation is clearly visible. Silicone fiber tube is resistant to low concentration of acid and alkali, high elasticity, not easy to age, and has a long service life. Resistant to high pressure and can be kept intact under high pressure and vacuum. PVC steel wire pipe is made of new PVC reinforced materials, and has made great progress in compressive strength and hardness. The main production method of silica gel steel wire pipe is multiple production method. The main types of steel wire pipe in shopping malls include high pressure steel wire pipe, low pressure steel wire pipe, steel wire skeleton pipe and Tongming steel wire pipe. The application methods are different in different environments. The new PVC steel wire pipe is the most widely used commodity today. Suction pipe Where can I find it? After use, it will not be the same as the metal pipe, which is easy to deform and leak. What advantages does the PVC fiber reinforced pipe have.