The so-called acid and alkali resistant rubber hose is the rubber hose used to transport acid and alkali solutions, which can be divided into wear-resisting Acetylene tape , acid and alkali resistant cloth clip hose, etc; In actual production, using a certain proportion of recycled rubber for acid and alkali resistant rubber hose can not only reduce the cost of raw materials, but also improve the aging resistance of rubber compound, thus extending the service performance and service life of acid and alkali resistant rubber hose. However, if you want to significantly improve the aging resistance of acid and alkali resistant hose, it is impossible to rely solely on recycled rubber, and rubber antioxidant is essential. What anti-aging can be used in acid and alkali resistant hose? 1. Antioxidant A: Antioxidant A, namely, antioxidant A, is in the form of yellowish brown to purple crystal blocks at room temperature. It is a universal antioxidant, which has good resistance to heat, oxygen, flexion, weather and fatigue aging. It also has a certain inhibitory effect on harmful metals. It is easy to disperse in the rubber compound, and has no obvious impact on the processing performance of the rubber compound and the physical and mechanical strength of the vulcanizate, It is the preferred antioxidant product in the production of acid and alkali resistant hose. It can also be used as a stabilizer in the acid and alkali resistant hose containing styrene butadiene rubber, which can significantly delay the aging time of acid and alkali resistant hose. 2. Antioxidant D: antioxidant D, namely N-phenyl - β－ Naphthylamine (D) is a kind of heat aging resistance commonly used in the production of rubber products, Acetylene tape Price Anti aging agent resistant to fatigue aging; Due to the poor heat resistance of the acid and alkali resistant hose, the use of a small amount of antioxidant D in the protection system can improve the heat aging resistance of the rubber compound, thereby improving the heat resistance of the acid and alkali resistant hose, expanding the use temperature range, and extending the use time.

Common for ventilation duct wear-resisting Acetylene tape What should be paid attention to during processing: the galvanized air duct shall not be connected with s-shaped, c-shaped right angle and vertical angle plugs. Clasp type air duct shall not be used for Grade 1 to 5 clean air. The rivet spacing of air duct shall be less than 100 mm. When the air purification level is 1-5, the rivet spacing of air duct shall be less than 65 mm. Before processing the galvanized air duct, use cleaning solution to remove the oil stain and dust on the surface of the plate. The cleaning solution shall be a neutral detergent, which will not damage the board surface, and will not produce dust after drying, so it will not be harmful to human health. Clean the vent pipe with cleaning solution after fabrication. After cleaning, the electric board shall be sealed in time after the white silk cloth cleaning inspection meets the requirements. The inner wall of color coated steel pipe shall be smooth, and the coating shall not be damaged during steel plate processing. The damaged parts shall be coated with epoxy resin. The galvanized air duct seamed joints, riveted joints and flange flanged corner joints shall be sealed with sealant or other sealing measures according to the design and cleaning level requirements. The sealing materials shall be isobutyl rubber, chloroprene rubber, modified silica gel, etc. The sealing surface of the air duct plate joint shall be located at the positive pressure side of the air duct wall. The production site of galvanized air duct shall be relatively closed, and the production site shall be paved with soft materials that are not easy to produce dust. The galvanized air duct shall have fewer longitudinal joints, glass fiber reinforced plastic ventilation pipes, and no transverse joints. Acetylene tape Price The processing of connecting bolts, nuts, washers and rivets shall be galvanized or other anti-corrosion measures, and blind rivets shall not be used.

How to install correctly Guiyang Acetylene tape ？ In the fire smoke exhaust pipe system, the airport and air valve must use non fuel, and the thickness of citizen flue and galvanized ventilation pipe should be improperly used. The high-pressure system should be selected according to the national code GB50243. When the fire smoke exhaust fan is installed on the roof, certain maintenance measures should be taken. The exposed power line must be threaded through the conduit, and the conduit material should be combined with the metal hose or Capelli and duck neck equipment to make it curved. The fire fighting system and equipment lines must be fixed with special clamps to avoid falling. Stainless steel air duct and ventilation equipment shall be made of three fabric flame retardant materials with soft connection. It is suggested that the length should be 15-30cm, and the electrical interpenetration should be completed. Bolts require the same length. The three main bodies should be grounded, ventilation equipment, and equipment and devices between dynamic loads should be equipped with shock absorption measures. When Acetylene tape Price Box type pipe fittings should not be used for changing direction, variable diameter, branch road, or junction, but the wind speed of box section should not exceed 1.5m/s for air distribution and static pressure box when necessary; It is advisable to have 5-10 times the pipe diameter between conduit pipes. The length of expandable metal pipes or non-metallic soft links should not exceed 2 meters. There should be no disintegration and dead corners. During the installation process, when the length of pipe elbows and straight pipes exceeds 20 meters, add anti impact frame open room exhaust fans and add or subtract supports.

Industrial pollution is a signal of environmental protection. These industrial pollution must be environmentally friendly. These equipment and machinery, insulation air valve pollution sources and discharge routes must be applied to the pipeline. Guiyang Acetylene tape It is just one of the rare ventilation ducts. Let's take a look at the precautions of stainless steel pipe welding process. Stainless steel welded air duct is called welding nano, which is a kind of welding nano. Since the thickness of the pipe is 0.8-5.0mm, welding is rare in the market (the thickness of the seamless pipe formed in the steel plant is 5-30mm), which is different. It can be said that it is a thin wall welding nano. As the thickness of welded pipe, the thickness of welded pipe may not be required to be the same as that of seamless welding, but only to meet the national standard of ventilation pipe, and at the same time meet the requirements of full pressure and air volume in the ventilation system. In the application environment, the thickness of stainless steel welded air duct pipes can be customized according to the requirements of the enterprise factory (the demander) to adapt to the processing of welded pipes. In short, as long as the above requirements are met, the cost of the enterprise will be lower. As long as the enterprise factory knows that it needs more air volume to customize and sell the fan, and then press the full pressure and air volume of the fan, the welding size of the stainless steel pipe can be determined. Because of the small wind resistance of round air ducts, ordinary air ducts are rarely used to connect environmental protection equipment. even if wear-resisting Acetylene tape The air outlet of the equipment is square or round (also called square turn). Circles, heaven and earth, cylindrical dampers and circular places are connected to fans and air ducts. In this case, the circular pipe is very good for installation.