The so-called acid and alkali resistant rubber hose is the rubber hose used to transport acid and alkali solutions, which can be divided into high quality Rubber hose , acid and alkali resistant cloth clip hose, etc; In actual production, using a certain proportion of recycled rubber for acid and alkali resistant rubber hose can not only reduce the cost of raw materials, but also improve the aging resistance of rubber compound, thus extending the service performance and service life of acid and alkali resistant rubber hose. However, if you want to significantly improve the aging resistance of acid and alkali resistant hose, it is impossible to rely solely on recycled rubber, and rubber antioxidant is essential. What anti-aging can be used in acid and alkali resistant hose? 1. Antioxidant A: Antioxidant A, namely, antioxidant A, is in the form of yellowish brown to purple crystal blocks at room temperature. It is a universal antioxidant, which has good resistance to heat, oxygen, flexion, weather and fatigue aging. It also has a certain inhibitory effect on harmful metals. It is easy to disperse in the rubber compound, and has no obvious impact on the processing performance of the rubber compound and the physical and mechanical strength of the vulcanizate, It is the preferred antioxidant product in the production of acid and alkali resistant hose. It can also be used as a stabilizer in the acid and alkali resistant hose containing styrene butadiene rubber, which can significantly delay the aging time of acid and alkali resistant hose. 2. Antioxidant D: antioxidant D, namely N-phenyl - β－ Naphthylamine (D) is a kind of heat aging resistance commonly used in the production of rubber products, Rubber hose company Anti aging agent resistant to fatigue aging; Due to the poor heat resistance of the acid and alkali resistant hose, the use of a small amount of antioxidant D in the protection system can improve the heat aging resistance of the rubber compound, thereby improving the heat resistance of the acid and alkali resistant hose, expanding the use temperature range, and extending the use time.

Zibo Rubber hose It is a kind of hose that can be used for sand pumping and sand suction produced with high abrasion resistant rubber. It is often used in sand blasting industry, cement, steel, minerals and other industries, but it is mainly used in river dredging, slurry transportation in mines, sand digging and sand taking and other industries to transport sharp granular solids or solid-liquid mixtures. Its product structure is composed of high wear-resistant layer, reinforced water pipe layer, skeleton steel wire and outer rubber. Today, Myers will introduce the application field of wear-resistant sand absorption rubber pipe. When the wear-resistant sand suction rubber pipe is applied in the mine pit, it is necessary to set a floating boat equipped with a sand pump in the mine pit, and use the floating sand suction rubber pipe to connect with the sand pump. The floating boat will float up and down with the rise and fall of the water level. It is required that the pipe body has good flexibility and good tear resistance and bending resistance. The offshore pipeline is connected by non floating sand suction hose until the pulp transportation destination. The overall pipeline is divided into two parts, one for surface use and the other for onshore use. The main raw material of these two kinds of hoses is high abrasion and corrosion resistant rubber, and cord reinforcement layer and steel wire skeleton layer are added in the pipe wall to ensure the pressure resistance and tear resistance of the hose. The connection mode is vulcanized flange connection, that is, the flange and the hose are a whole, so there is no need to worry about the flange falling off. Floating sand suction hose used on the water surface. This kind of hose is required to float on the water surface. Due to the large drop of the mine (100 meters) and the long conveying distance Rubber hose company The hose shall have high pressure resistance, and the design pressure is 25 kg/cm2 according to the calculation. It should be considered that the floating ship will move up and down with the rise and fall of the water level and the wave will cause lateral displacement. Its internal structure is the same as the sand suction hose used offshore, except that a floating body is installed outside the hose.

1. Mutual wear of rubber lining plate and steel ball of ball mill: both the rubber lining plate and steel ball of ball mill are vulnerable parts. During grinding, the steel ball and material of ball mill do throw line falling movement in the barrel Zibo Rubber hose It will collide with steel balls and materials and cause friction. In continuous operation, the rubber lining plate and steel ball of ball mill will be severely worn, which is directly related to the hardness of materials. The greater the hardness of the material, the faster the abrasion speed of the rubber lining plate and steel ball of the ball mill, which may cause equipment damage or even safety accidents in serious cases. In addition, it is also related to the ball of the ball mill. The size and quantity of the ball will affect the service life of the rubber lining plate of the ball mill. If the ball mill is in operation, increasing the amount of steel balls or filling steel balls with larger diameters will increase the wear of the rubber lining plate of the ball mill. 2. The heat treatment process of the rubber lining plate of the ball mill is unreasonable: the unreasonable heat treatment of the rubber lining plate of the ball mill will not only increase the wear of the lining plate, but also affect the yield strength of the lining plate, resulting in the fracture of the bolt of the ball mill under the large shear force. In the actual operation, the staff lacked the understanding of the lining plate material and the heat treatment processing of the ball mill rubber lining plate was insufficient, so the strengthening effect of the ball mill rubber lining plate was not in place and the strength was low. When impacted by steel balls and materials, Rubber hose company Plastic deformation often occurs. 3. The material of the rubber lining plate of the ball mill is unreasonable: the material of the rubber lining plate of the ball mill and its heat treatment process are the key to determine the mechanical performance of the lining plate. If the material of the lining plate is not properly selected, its fatigue strength and life will be greatly reduced, which will not meet the requirements of the ball mill, or even plastic deformation or bulge will occur.

The consumption of galvanized iron sheet air duct in China's chemical industry also shows a rapid growth trend. The rapid increase in the consumption of galvanized iron sheet air duct in China's chemical industry has stimulated domestic Rubber hose company With the rapid development of industry and the support of relevant government policies, in a short period of time, the production of galvanized iron air ducts in China has been developing rapidly. From the perspective of industrial chain, galvanized iron duct and upstream and downstream products enterprises of galvanized iron duct are interdependent and competing industries. Steel production enterprises can establish long-term and stable strategic alliances with downstream enterprises through deep processing of steel products, which is conducive to promoting the development of new varieties, quality improvement and market expansion of galvanized iron sheet air duct industry, and is an effective way to extend the value of steel products to the downstream and improve the competitiveness of the product market. It can be said that the development of high-quality galvanized iron duct projects has become a development strategy for Chinese galvanized iron duct manufacturers to cope with fierce market competition and improve product competitiveness. At present, in the consumption structure of galvanized iron duct in China, except for some high-end products that still rely on imports, middle and low-end products can basically achieve self-sufficiency. The situation that galvanized iron duct consumption completely depends on imports has been greatly improved, and the export volume is also expanding rapidly. However, compared with the developed areas of galvanized iron duct industry, China's galvanized iron duct industry system is not perfect, and there is still a big gap compared with Japan, South Korea and other large stainless steel reactor production countries. The development of galvanized iron sheet air duct industry in China started late, and the social demand for stainless steel reaction kettle grew too fast, which led to high quality Rubber hose The first problem to be solved for industrial development is to rapidly increase output to meet the growing social demand, gradually replace imports, and complete the two steps of "quantitative change" and "qualitative change". At present, the development of galvanized iron duct industry in China has completed the accumulation process of "quantitative change", and is currently facing the transformation of "quality".

Before construction, the technicians must be familiar with the drawings and relevant data carefully, and understand the technological process, working medium, pressure, temperature and other technical parameters as well as the materials, models and specifications of the materials and accessories used. The construction personnel must be fully familiar with the construction procedures, construction methods, quality standards, operating procedures and safety technical requirements, and strictly implement them during construction. Main materials used for making galvanized air duct, Zibo Rubber hose It shall comply with the current national product standards and the enterprise standards of the manufacturer, and shall have the factory certificate and other relevant material certificates. All material accessories must be rechecked with the design and current national product standards, and shall have the factory certificate, material quality assurance and other relevant material certificates. Combined flange air duct is also called thin-walled steel plate flange air duct. It is an air duct connected by non profile steel and made of galvanized steel plate. Its connection form can be directly pressed by strips or steel plates or the air duct and flange can be integrally formed. This kind of air duct has advanced manufacturing technology, accurate blanking, low material consumption, stable product quality, many varieties, smooth contour lines, and air leakage rate far lower than the national standard, which is conducive to the production of ventilation ducts to be industrialized, large-scale, standardized and automated. It is a scientific and technological achievement project that has been vigorously promoted in China in recent years as one of the non blue air duct processes. The National Grand Theater project is to use this new process air duct. Common plate flange air duct 1 Fabrication of composite flange air duct Common mechanical equipment for fabrication of composite flange air duct include: rectangular air duct full-automatic production line, plasma automatic cutting machine, flange strip forming machine, hook code forming machine, conjoined flange forming machine, etc. The combined flange air duct is based on the air duct size given in the drawing, Rubber hose company Fully automatic production line is used to produce coiled material with a common width of 1250mm, and the plate thickness is 0.5~1.2mm. When the large side of the air duct is less than or equal to 2m, the air duct is formed into TDC1 flange, and the standard pipe length is 1170mm; When the large side of the fabricated air duct is less than or equal to 2.5m, the air duct is formed into TDC2 flange, and the standard pipe length is 1250mm; When the large side of the fabricated air duct is more than 2.5m, the air duct is formed into an angle steel flange, and the standard pipe length is 1230mm

high quality Rubber hose 1. During the molding of rubber products, the cohesive force of the elastomer cannot be eliminated due to the large pressure pressing. During the molding and mold release, extremely unstable shrinkage (the shrinkage rate of rubber varies due to different rubber types) often occurs. It must take a period of time before it can be gentle and stable. Therefore, at the beginning of the design of a rubber product, no matter the formula or the mold, it is necessary to carefully calculate the matching. If not, it is easy to cause dimensional instability of the product, resulting in low product quality. 2. Rubber belongs to thermosetting elastomer, while plastic belongs to thermosetting elastomer. Due to different sulfide types, the temperature range of rubber molding and curing is quite different, even affected by climate change and indoor temperature and humidity. Therefore, the production conditions of rubber products need to be properly adjusted at any time. If not, there may be differences in product quality. 3. The rubber product is the rubber mixture made from rubber raw materials after mixing in the internal mixer as the raw material. The formula is designed according to the characteristics of the required rubber products during mixing, and the required product hardness is determined. The product is molded by the rubber plate vulcanizer. After the product is formed, flash processing shall be carried out to make the product surface smooth without burrs. 4. The aging test of rubber products belongs to the category of aging test. Rubber aging refers to the phenomenon that the performance and structure of rubber and products are changed due to the combined effect of internal and external factors in the process of processing, storage and use, thus losing their use value. Rubber hose company It is characterized by cracking, tackiness, hardening, softening, chalking, discoloration, mildew, etc. The following conditions shall be met when the ball mill uses the rubber lining plate: 1. The hardness of the ground material. The iron base alloy is similar to the rubber lining plate for materials below medium hardness, and the rubber lining plate is superior for materials above medium hardness. 2. The temperature of rubber lining plate is generally 70 ℃ - 90 ℃, and it can reach 110-130 ℃ under special circumstances. The temperature should be lower during dry grinding. 3. Feed size. Generally, the ball mill shall be more than 20-25mm; For the autogenous mill, the feeding particle size can be larger because no steel ball is added.