The hard core method adopts the core extrusion process to extrude the inner rubber tube blank, which directly uses the extruder to cover the inner rubber tube blank on the iron core, instead of the traditional casing process, and simplifies the process flow. the north sea Oil hose The billet forming adopts the process method of intertwining outer film and steel wire braiding forming. Similar to wrapping water wrapped cloth, the overlapping width is 1/2 of the film width. This process method can replace the method of wrapping outer film by extruder or by hand, reducing energy consumption and cost. We all know that the reinforcing layer and reinforcing layer of the rubber hose are the main force bearing parts, which are used to bear the load pressure. The factors determining the stress condition of the reinforced layer of the rubber hose are determined by the tension of the braided steel wire and the braiding angle. The high-speed steel wire hose braiding machine developed by our factory has introduced the advanced technology of foreign braiding production lines, and integrated the characteristics of domestic braiding machines. It integrates the advanced functions of hydraulic brake hose braiding production line, such as horizontal mechanical transmission, automatic lubrication, and so on, to develop equipment with high productivity and high degree of automation. The range of braiding diameter can be achieved Ф 6— Ф 25 Long core rubber hose (reinforcement layer). It fills the gap of domestic knitting production equipment, which can be widely used in rubber and plastic hose, rubber hose (reinforcement layer) knitting production equipment. The structure of high-pressure rubber hose is composed of four parts: inner liner, inner rubber layer, skeleton layer, middle rubber layer and outer rubber layer. Oil hose Price In case of direct contact with the conveying medium, the synthetic rubber with good medium resistance, high tensile strength, high constant tensile stress, small compression permanent deformation and easy processing is usually selected. In order to meet the use requirements of strong polar medium resistance, the inner liner is composed of polytetrafluoroethylene layer and rubber layer, and a layer of film or adhesive is added on the surface of the inner liner to improve the adhesion with the skeleton material.

What is stainless steel spiral duct? Oil hose Price The products are mainly used to connect the air flow between two places and play the role of ventilation. There are three types of galvanized spiral air ducts, stainless steel spiral air ducts and composite spiral air ducts. Here we mainly talk about the stainless steel spiral air duct, and briefly analyze the reason why it is widely used in villas. The so-called stainless steel air duct is strictly a kind of air duct processing technology, also known as spiral seamed thin-walled tube. The best quality is the thin-walled tube with spiral seamed made of metal strips. Because the applied material is metal, it is also called spiral seamed metal tube. It was first used in the military industry of western countries, such as ships, ship ventilation, air conditioning systems, and later used in trains Subway, mine and other civil facilities. By 2000, according to statistics, 95.6% of office buildings, shopping malls and subways in the United States had applied spiral air ducts. In civil residential buildings, 72.5% of central air conditioners use spiral air ducts. Since the mid-1990s, China has introduced this technology into the shipbuilding industry. With the rapid development of China's economy, the use of central air conditioners has increased year by year, and the quality of auxiliary products for exhaust and air supply has been continuously improved. Spiral air ducts have been widely used in some villas. (1) Product standardization: The production of spiral round air duct fittings (pipe fittings and joints) has been highly automated, systematic, and has industrialized quality control. It is well known that the wind resistance of circular duct is much smaller than that of rectangular duct. (2) Easy to install. The installation of spiral air duct significantly reduces the connection points between pipes and minimizes the leakage at the joint of pipe fittings. The typical spiral air duct is 3~6m long, while the typical rectangular air duct is only 1~1.5m long; The connection of two spiral air ducts requires only one pipe connector, while the connection of traditional rectangular air ducts often requires a completely independent double flange system. (3) Usually only small installation space is required: the same production Oil hose The circular pipe with a diameter of 200mm in the installation space can replace 250 × 150mm rectangular pipe. On the premise of not increasing additional installation space, several parallel circular pipes can replace flat rectangular pipes.

the north sea Oil hose It is a kind of hose that can be used for sand pumping and sand suction produced with high abrasion resistant rubber. It is often used in sand blasting industry, cement, steel, minerals and other industries, but it is mainly used in river dredging, slurry transportation in mines, sand digging and sand taking and other industries to transport sharp granular solids or solid-liquid mixtures. Its product structure is composed of high wear-resistant layer, reinforced water pipe layer, skeleton steel wire and outer rubber. Today, Myers will introduce the application field of wear-resistant sand absorption rubber pipe. When the wear-resistant sand suction rubber pipe is applied in the mine pit, it is necessary to set a floating boat equipped with a sand pump in the mine pit, and use the floating sand suction rubber pipe to connect with the sand pump. The floating boat will float up and down with the rise and fall of the water level. It is required that the pipe body has good flexibility and good tear resistance and bending resistance. The offshore pipeline is connected by non floating sand suction hose until the pulp transportation destination. The overall pipeline is divided into two parts, one for surface use and the other for onshore use. The main raw material of these two kinds of hoses is high abrasion and corrosion resistant rubber, and cord reinforcement layer and steel wire skeleton layer are added in the pipe wall to ensure the pressure resistance and tear resistance of the hose. The connection mode is vulcanized flange connection, that is, the flange and the hose are a whole, so there is no need to worry about the flange falling off. Floating sand suction hose used on the water surface. This kind of hose is required to float on the water surface. Due to the large drop of the mine (100 meters) and the long conveying distance Oil hose Price The hose shall have high pressure resistance, and the design pressure is 25 kg/cm2 according to the calculation. It should be considered that the floating ship will move up and down with the rise and fall of the water level and the wave will cause lateral displacement. Its internal structure is the same as the sand suction hose used offshore, except that a floating body is installed outside the hose.

Many people don't know much about spiral tube. In fact production Oil hose It is very extensive. Spiral air duct is mainly used to connect the two places for ventilation. Spiral air ducts (stainless steel and galvanized iron sheet) are widely used in the market. Spiral air duct market is generally divided into three categories according to material: galvanized spiral air duct, stainless steel spiral air duct and composite spiral air duct. Among them, the stainless steel air duct has good quality and strong applicability, but its price is high. The return air duct of purification system, central air conditioning ventilation duct, industrial air supply and exhaust duct, environmental protection system suction and exhaust duct, mine gas drainage duct, mine coating duct, etc. The spiral duct is first used for ventilation and cooling, which belongs to the category of air duct. It is named according to its purpose, but it can also be used in other places, even for drainage, drainage or as a container, which cannot be called a pipe. Named according to the structure, it should be called spiral grooved thin-walled tube, because it is mainly made of metal, also called spiral grooved metal tube. According to the material name, there may be several names: galvanized (any zinc) (galvanized) (iron), spiral pipe, stainless steel spiral pipe (stainless steel acid resistant steel), aluminum (aluminum) spiral pipe, or in order to distinguish from the existing acid resistant stainless steel pipe, Oil hose Price It can be called ultra-thin stainless steel pipe, because it can use 0.3mm or even thinner to roll stainless steel strip.

the north sea Oil hose Prevention of vibration and noise during installation: the prevention of vibration and noise during installation is a key point in the installation process. The prevention of vibration and noise of spiral air duct during installation is mainly from the following aspects: 1. The fan and spiral air duct are connected by hose, and the hose at the suction inlet of the fan shall be installed with appropriate tightness, Avoid noise and vibration caused by reducing the area of air inlet and outlet due to loose soft connection. 2. The spiral air duct shall be made, installed and connected with the components. The connection shall be tight to reduce the gap and avoid air leakage noise. 3 In order to prevent the spiral air duct from vibration, fixed supports shall be installed at the turning of each system spiral air duct and at the connection with the ventilator and the air outlet for shock absorption. 4 The vibration damping device shall be set according to the design requirements or construction specifications during fan installation. Air leakage rate test of spiral air duct After the installation of spiral air duct, air leakage rate test shall be carried out. According to the specifications, the air leakage rate test of spiral air duct adopts the combination of light leakage legality and quantitative air leakage rate test. The light leakage method is suitable for the tightness test of medium and low pressure systems; The air leakage rate test is suitable for sampling inspection of medium pressure system and full detection of high pressure system. Light leak detection of spiral air duct Light leak detection is a qualitative method to detect the tightness of the spiral air duct of the system by using the strong penetration of light to holes. The test method is to use a bulb with protective cover whose voltage is not higher than 36V and power is more than 100W in the spiral air duct on a certain length of spiral air duct in dark environment, and slowly move from one end of the spiral air duct to the other end. If light can be observed outside the spiral air duct during the test, it indicates that there is a leak point in the spiral air duct, and repair the leak point of the spiral air duct. Oil hose Price The light leak detection method of the low-pressure system adopts the method of subsection detection and summary analysis. The spiral air duct of the tested system is not allowed to have multiple obvious light leaks in the form of slits. The spiral air duct of the low-pressure system has no more than two light leak points every 10 meters, and the average joint of 100 meters is no more than 16; For every 10 joints of spiral air duct of medium pressure system, no more than 1 light leak point, and no more than 8 joints per 100 meters are qualified.