wear-resisting Acetylene tape 1. During the molding of rubber products, the cohesive force of the elastomer cannot be eliminated due to the large pressure pressing. During the molding and mold release, extremely unstable shrinkage (the shrinkage rate of rubber varies due to different rubber types) often occurs. It must take a period of time before it can be gentle and stable. Therefore, at the beginning of the design of a rubber product, no matter the formula or the mold, it is necessary to carefully calculate the matching. If not, it is easy to cause dimensional instability of the product, resulting in low product quality. 2. Rubber belongs to thermosetting elastomer, while plastic belongs to thermosetting elastomer. Due to different sulfide types, the temperature range of rubber molding and curing is quite different, even affected by climate change and indoor temperature and humidity. Therefore, the production conditions of rubber products need to be properly adjusted at any time. If not, there may be differences in product quality. 3. The rubber product is the rubber mixture made from rubber raw materials after mixing in the internal mixer as the raw material. The formula is designed according to the characteristics of the required rubber products during mixing, and the required product hardness is determined. The product is molded by the rubber plate vulcanizer. After the product is formed, flash processing shall be carried out to make the product surface smooth without burrs. 4. The aging test of rubber products belongs to the category of aging test. Rubber aging refers to the phenomenon that the performance and structure of rubber and products are changed due to the combined effect of internal and external factors in the process of processing, storage and use, thus losing their use value. Acetylene tape Where can I find it? It is characterized by cracking, tackiness, hardening, softening, chalking, discoloration, mildew, etc. The following conditions shall be met when the ball mill uses the rubber lining plate: 1. The hardness of the ground material. The iron base alloy is similar to the rubber lining plate for materials below medium hardness, and the rubber lining plate is superior for materials above medium hardness. 2. The temperature of rubber lining plate is generally 70 ℃ - 90 ℃, and it can reach 110-130 ℃ under special circumstances. The temperature should be lower during dry grinding. 3. Feed size. Generally, the ball mill shall be more than 20-25mm; For the autogenous mill, the feeding particle size can be larger because no steel ball is added.

We are all denominators. Why treat ourselves as molecules. But I think we Acetylene tape Where can I find it? The mass of is absolutely the molecule in the same industry. From raw materials, the general manager is responsible for the purchase of raw materials. Raw materials can only enter the factory after passing the inspection. Because it is the boss's own purchase and inspection, there is no buyer to take kickback, which increases the cost of raw materials and reduces the quality of raw materials. Speaking of the manufacturer's production process, it is difficult to find the second advanced mixer equipment among the new sand pumping hose manufacturers in 2019. It ensures that our glue is more uniform. This ensures the quality of our sand pumping hose. About 70% of sand pumping hose is manual work, and the production technology experience of workshop workers largely determines the quality of our sand pumping hose. 70% of our workshop workers have more than 7 years of production wear-resisting Acetylene tape Experience. Select rubber hose Wang Xueyan purchases sand pumping rubber hose, which is more insurance than insurance company. Our goal is to become a member of the hose industry with excellent sand pumping hose quality. Place an order yesterday and deliver it today. At this speed, it is hard to find a second sand pumping hose in the industry. Life doesn't treat us kindly because we are women. But we should treat our own lives well and try to sell sand pumping hoses. As an excellent salesman, will you also receive an inquiry like chicken ribs. When I was just doing business, I received a 3 page quotation, and I patiently sorted it out for about 2 days. Finally, there was no news. Now I have been doing business for more than 10 years. Sometimes I can accurately judge the order rate of this order simply by looking at the inquiry list. The real heart of the words lies in the customers who make good deals.

Industrial pollution is a signal of environmental protection. These industrial pollution must be environmentally friendly. These equipment and machinery, insulation air valve pollution sources and discharge routes must be applied to the pipeline. Tibet Acetylene tape It is just one of the rare ventilation ducts. Let's take a look at the precautions of stainless steel pipe welding process. Stainless steel welded air duct is called welding nano, which is a kind of welding nano. Since the thickness of the pipe is 0.8-5.0mm, welding is rare in the market (the thickness of the seamless pipe formed in the steel plant is 5-30mm), which is different. It can be said that it is a thin wall welding nano. As the thickness of welded pipe, the thickness of welded pipe may not be required to be the same as that of seamless welding, but only to meet the national standard of ventilation pipe, and at the same time meet the requirements of full pressure and air volume in the ventilation system. In the application environment, the thickness of stainless steel welded air duct pipes can be customized according to the requirements of the enterprise factory (the demander) to adapt to the processing of welded pipes. In short, as long as the above requirements are met, the cost of the enterprise will be lower. As long as the enterprise factory knows that it needs more air volume to customize and sell the fan, and then press the full pressure and air volume of the fan, the welding size of the stainless steel pipe can be determined. Because of the small wind resistance of round air ducts, ordinary air ducts are rarely used to connect environmental protection equipment. even if wear-resisting Acetylene tape The air outlet of the equipment is square or round (also called square turn). Circles, heaven and earth, cylindrical dampers and circular places are connected to fans and air ducts. In this case, the circular pipe is very good for installation.

Tibet Acetylene tape 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Acetylene tape Where can I find it? When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.

With the rapid development of the national economy and the continuous improvement of the technical level, almost all walks of life need to do exhaust ventilation systems, Tibet Acetylene tape What are the advantages worth pursuing? 1. The welding method is unique. It adopts a new low temperature welding form, which does not damage the galvanized layer of the product. The welding spot is firm, the weld seam is beautiful, and the sealing is good. After welding, no treatment is required for the weld seam. 2. The manufacture of mechanically formed air duct makes the high-quality galvanized sheet not damaged, and the galvanized layer not damaged, thus prolonging the service life. 3. The specification is uniform and the size is standard, which ensures that the inner wall of the pipeline is flat and smooth, so that it is easy to clean and the material transportation is smooth. 4. The self forming flange can make the pipe material uniform, no longer use angle steel flange, and reduce the pipe weight by more than 20%, so the load bearing capacity of the building can be greatly reduced, thus reducing the overall cost of the building. 5. Enhance the beautiful pipeline, beautiful appearance, exquisite structure, smooth lines, superior performance, and the installation of exposed air ducts, especially suitable for this product. 6. Typical round air pipe fittings are generally 3-6 meters long and rectangular pipe fittings are 1-1.5 meters long, reducing the connection points of pipe fittings and minimizing the leakage at the joint of pipe fittings. 7. The pipe fittings, joints and spare parts made by mechanized assembly line all have standard sealing rings. As they are produced in a standardized and factory way, they have better air tightness. 8. Mechanically formed compression ribs and stiffeners can improve the strength of the pipe wall, save material thickness and reduce costs. The thickness of the seam of the spiral pipe is 4 times that of the pipe body, which makes the pipe very rigid and has the best pressure bearing performance, especially the negative pressure. 9. Scientific joint and seaming methods can ensure smooth pipeline gas without affecting pipeline flow diameter. Therefore, mechanized assembly line production improves production efficiency and effectively shortens delivery cycle. Advanced computer process control program blanking, production, Acetylene tape Where can I find it? It ensures the dimensional accuracy of pipeline components, thus ensuring fast and convenient installation and construction, and improving work efficiency and economic benefits.