Sandblasting pipe Where can I find it? Precautions ① The acid and alkali resistant rubber hose used shall not only be oil resistant, but also be pressure resistant, heat resistant, cold resistant, wear resistant and aging resistant. ② The rubber hose should not be too long or too short, generally 1.4 meters. ③ The interface is tight and can be fastened with thin iron wire or clip to prevent falling off and air leakage. ④ It is forbidden to pull acid and alkali resistant rubber hose from one room to another or through walls, floors and floors to prevent accidents caused by rubber hose breaking and falling off. ⑤) The acid and alkali resistant rubber hose should be placed in a place where it can be seen frequently, so that it is easy to detect leakage. Check whether the rubber hose leaks after each bottle change. ⑥ Do not replace acid and alkali resistant rubber hose with universal rubber hose. Since the full rubber hose does not contain a skeleton layer, it is only necessary to use a press out machine to press out the hose; The cloth clamping hose needs to use a molding machine that wraps the adhesive tape on the inner adhesive layer; When forming the suction hose, first wrap the metal spiral wire and then wrap the inner rubber; Special fabric knitting machine or winding machine shall be used for knitting and winding hose; Knitting machine is required for knitting hose. Jiaozuo Sandblasting pipe The basic production processes include rubber mix processing, cord fabric and canvas processing, rubber tube molding, vulcanization, etc. The manufacturer of acid and alkali resistant rubber hose said that the processing method of the skeleton layer and the forming equipment of the rubber hose are different for different structures and different skeletons.

Ventilation pipes on ships are generally made of galvanized iron sheet high quality Sandblasting pipe This kind of air duct is generally made by hand, and the production efficiency is low. Later, circular spiral air ducts made by machines greatly improved the production efficiency of air ducts and the quality of air ducts, which were widely used on civilian ships. However, for military ships with very strict height restrictions, circular air ducts obviously occupied more height than rectangular air ducts, which limited the promotion and use of circular spiral air ducts on ships. In the 1980s, 708 Research Institute, the Military Representative Office of Navy Garrison 426 Factory and Dalian Bohai Air Conditioning Auxiliary Factory jointly successfully trial produced the flat spiral air duct. It combines the advantages of the circular spiral air duct and the rectangular air duct. It is the third generation of air duct for ships, which is welcomed by the ship design department and has achieved good results after many ship use. The structure of the spiral air duct is the same as the round spiral air duct. It is also formed by rolling galvanized iron sheet on a special pipe coiler. Therefore, it can be produced mechanically, and the inner surface of the air duct is flat and smooth. The utilization rate of materials is also high. The thickness of galvanized iron sheet is generally 0.6mm. Although it is 0.75~slightly thinner than the commonly used rectangular air duct iron sheet, its rigidity is higher than that of rectangular air duct due to the reinforcement effect of spiral undercut. There are two types of flat spiral air duct: non adiabatic and pre adiabatic. Non adiabatic type is applicable to air conditioning ducts with simple mechanical ventilation, natural ventilation and external insulation. Jiaozuo Sandblasting pipe There are two types, one is air layer insulation, that is, there is 12.5~thick air layer between the inner pipe and the outer pipe. The other is that the inner and outer pipes are filled with thermal insulation materials rock wool or ultra-fine glass wool to become good thermal insulation air conditioning ducts.

Jiaozuo Sandblasting pipe The structure is composed of liquid resistant synthetic rubber inner rubber layer, medium rubber layer, I or II or III steel wire braid reinforcement layer, and weather resistant synthetic rubber outer rubber layer. Sand pumping hose features: 1. Sand pumping hose is made of special synthetic rubber, which has excellent oil resistance, heat resistance and aging resistance. 2. The rubber hose has high bearing pressure and excellent pulse performance. 3. The pipe body is tightly combined, soft to use, and has little deformation under pressure. 4. Sand pumping hose has excellent bending resistance and fatigue resistance. 5. The sand pumping hose is long, φ 20 meters above 32, φ Below 25 meters, it can reach 10 meters or even 100 meters. Sand pumping hose parameters: 1. The inner wall of nylon cord hose is smooth and has little friction. Reinforcing layer: high-strength synthetic wire, spiral winding of steel wire and iron wire (sand suction pipe) 2 high quality Sandblasting pipe Flange connection (ANSI150 standard flange) 3. Nominal pressure: 20BAR4, temperature: - 50 ℃ -+95 ℃ 5. Working pressure of sand suction hose and mud discharge pipe: positive pressure: 10kg; Test pressure: working negative pressure of 15kg steel ring sand suction hose: ≥ 15kg sand suction hose has strong flexibility, which is mainly used as the sand pump sand discharge pipe to connect the sand transport pipe and sand pump, as well as the pipe connection bend.

Let's take a look today Jiaozuo Sandblasting pipe How should the maintenance work be done? Firstly, the thickness of galvanized air duct splice plate shall be within the range specified in various specifications. If it is less than the thickness, it is easy to have defects such as cracking and wrinkling due to significant increase of bending force, abnormal damage of forming roll, overload of transmission system, boring, etc. Secondly, in the dedusting system: galvanized air ducts can be used for the collection and transportation of dedusting devices. In terms of air exhaust system: there is a large amount of smoke in the dining room, dining room and hotel kitchen, which needs air exhaust. The galvanized pipe is more appropriate, with good strength, economy and practicality. In air conditioning system: galvanized air duct can be pasted with thermal insulation materials, and the surface is beautiful. In bulk material transportation: in the pneumatic conveying system, some materials with fine loose particles can be transported by galvanized pipes, which has low cost and good effect. In the ventilation system: fresh air is supplied and discharged, harmful gases are discharged outdoors, and outdoor fresh air is sent indoors. The strength of stainless steel plate is greater than that of ordinary steel plate. When stainless steel plate is used for seaming, first of all, a forming test should be carried out to avoid overloading of equipment and excessive wear or mechanical problems. Due to the poor plasticity of aluminum plate, it is easy to crack when biting into forming. Forming test shall be conducted before construction. The last point is that the protection and decoration of the galvanized layer of the galvanized air duct can be significantly improved after passivation treatment, dyeing or brushing light protective agent. and Jiaozuo Sandblasting pipe The fire prevention function of is mainly reflected in that it is nonflammable, but it should be noted that whether the insulation layer is burned depends on the material. We recommend that galvanized air duct materials use nonflammable insulation materials such as centrifugal glass wool.