For the woodworking industry, many users high quality Sanding pipe Not unfamiliar, this is an industrial dust collector used on woodworking carving machines, mainly used to absorb wood chips, wood ash, etc. At present, there are many kinds of woodworking vacuum tubes on the market. In the past few years, major furniture factories used PVC steel wire hoses with flat ends. In recent years, more and more enterprises have replaced cheap PVC steel wire hoses with more wear-resistant and durable pu steel wire expansion tubes. Some of the former take a few days or a month, while some of the latter take a few months or a year, They are also steel wire hoses. Why is the service life gap so far? First of all, you may have the impression that many PVC hoses have a very bad smell. This kind of hose is often used in daily life. Because the raw material itself is very cheap, the price of the finished product is also very low. For example, only a dozen yuan a piece. Think about the price of PVC raw materials, which is generally 8-15 yuan a kilogram, And most businesses will not use expensive PVC raw materials, Sanding pipe Where can I find it? The woodworking vacuum tube produced in this way has a very strong smell, not only unpleasant, but also many times the product can not even achieve environmental protection. However, the current updated product, pu steel wire telescopic tube, is a large woodworking furniture factory. An expensive woodworking carving machine uses a cheap vacuum tube with a very smelly smell, which has much to do with the overall style.

We are all denominators. Why treat ourselves as molecules. But I think we Sanding pipe Where can I find it? The mass of is absolutely the molecule in the same industry. From raw materials, the general manager is responsible for the purchase of raw materials. Raw materials can only enter the factory after passing the inspection. Because it is the boss's own purchase and inspection, there is no buyer to take kickback, which increases the cost of raw materials and reduces the quality of raw materials. Speaking of the manufacturer's production process, it is difficult to find the second advanced mixer equipment among the new sand pumping hose manufacturers in 2019. It ensures that our glue is more uniform. This ensures the quality of our sand pumping hose. About 70% of sand pumping hose is manual work, and the production technology experience of workshop workers largely determines the quality of our sand pumping hose. 70% of our workshop workers have more than 7 years of production high quality Sanding pipe Experience. Select rubber hose Wang Xueyan purchases sand pumping rubber hose, which is more insurance than insurance company. Our goal is to become a member of the hose industry with excellent sand pumping hose quality. Place an order yesterday and deliver it today. At this speed, it is hard to find a second sand pumping hose in the industry. Life doesn't treat us kindly because we are women. But we should be kind to our own lives and try to sell sand pumping hoses. As an excellent salesman, will you also receive an inquiry like chicken ribs. When I was just doing business, I received a 3 page quotation, and I patiently sorted it out for about 2 days. Finally, there was no news. Now I have been doing business for more than 10 years. Sometimes I can accurately judge the order rate of this order simply by looking at the inquiry list. The real heart of the words lies in the customers who make good deals.

Zhengzhou Sanding pipe It is a kind of hose that can be used for sand pumping and sand suction produced with high abrasion resistant rubber. It is often used in sand blasting industry, cement, steel, minerals and other industries, but it is mainly used in river dredging, slurry transportation in mines, sand digging and sand taking and other industries to transport sharp granular solids or solid-liquid mixtures. Its product structure is composed of high wear-resistant layer, reinforced water pipe layer, skeleton steel wire and outer rubber. Today, Myers will introduce the application field of wear-resistant sand absorption rubber pipe. When the wear-resistant sand suction rubber pipe is applied in the mine pit, it is necessary to set a floating boat equipped with a sand pump in the mine pit, and use the floating sand suction rubber pipe to connect with the sand pump. The floating boat will float up and down with the rise and fall of the water level. It is required that the pipe body has good flexibility and good tear resistance and bending resistance. The offshore pipeline is connected by non floating sand suction hose until the pulp transportation destination. The overall pipeline is divided into two parts, one for surface use and the other for onshore use. The main raw material of these two kinds of hoses is high abrasion and corrosion resistant rubber, and cord reinforcement layer and steel wire skeleton layer are added in the pipe wall to ensure the pressure resistance and tear resistance of the hose. The connection mode is vulcanized flange connection, that is, the flange and the hose are a whole, so there is no need to worry about the flange falling off. Floating sand suction hose used on the water surface. This kind of hose is required to float on the water surface. Due to the large drop of the mine (100 meters) and the long conveying distance Sanding pipe Where can I find it? The hose shall have high pressure resistance, and the design pressure is 25 kg/cm2 according to the calculation. It should be considered that the floating ship will move up and down with the rise and fall of the water level and the wave will cause lateral displacement. Its internal structure is the same as the sand suction hose used offshore, except that a floating body is installed outside the hose.

Ventilation pipes on ships are generally made of galvanized iron sheet high quality Sanding pipe This kind of air duct is generally made by hand, and the production efficiency is low. Later, circular spiral air ducts made by machines greatly improved the production efficiency of air ducts and the quality of air ducts, which were widely used on civilian ships. However, for military ships with very strict height restrictions, circular air ducts obviously occupied more height than rectangular air ducts, which limited the promotion and use of circular spiral air ducts on ships. In the 1980s, 708 Research Institute, the Military Representative Office of Navy Garrison 426 Factory and Dalian Bohai Air Conditioning Auxiliary Factory jointly successfully trial produced the flat spiral air duct. It combines the advantages of the circular spiral air duct and the rectangular air duct. It is the third generation of air duct for ships, which is welcomed by the ship design department and has achieved good results after many ship use. The structure of the spiral air duct is the same as the round spiral air duct. It is also formed by rolling galvanized iron sheet on a special pipe coiler. Therefore, it can be produced mechanically, and the inner surface of the air duct is flat and smooth. The utilization rate of materials is also high. The thickness of galvanized iron sheet is generally 0.6mm. Although it is 0.75~slightly thinner than the commonly used rectangular air duct iron sheet, its rigidity is higher than that of rectangular air duct due to the reinforcement effect of spiral undercut. There are two types of flat spiral air duct: non adiabatic and pre adiabatic. Non adiabatic type is applicable to air conditioning ducts with simple mechanical ventilation, natural ventilation and external insulation. Zhengzhou Sanding pipe There are two types, one is air layer insulation, that is, there is 12.5~thick air layer between the inner pipe and the outer pipe. The other is that the inner and outer pipes are filled with thermal insulation materials rock wool or ultra-fine glass wool to become good thermal insulation air conditioning ducts.

People buy in daily life high quality Sanding pipe Take it home for installation. It is obviously installed very well, but the spiral air duct will become loose for a long time, which gives most users a headache. So what is the problem with spiral air duct reinforcement? This is of course necessary. The following manufacturer of galvanized spiral air duct will give you a detailed introduction. 1. Reinforcement measures shall be taken for circular pipes (excluding spiral pipes) with a diameter greater than or equal to 80 mm, a section length greater than 1250 mm or a total area greater than 4 ㎡; 2. The side length of rectangular air duct is more than 630 mm, the length of pipeline insulation side is more than 800 mm, the section length is more than 1250 mm, or the plane area of one side of low pressure pipeline is more than 1.2 m2, and that of medium and high pressure pipeline is more than 1.0 m2, so reinforcement measures should be taken; 3. For reinforcement of irregular oval pipes, the reinforcement method of rectangular pipes shall be referred to. The spiral air duct manufacturer Hongyuansheng Electromechanical also has something to say: the reinforcement of galvanized air duct non-metallic air duct should also meet the following requirements: when the diameter or side length of the rigid PVC pipe is greater than 500 mm, the connection between the pipe and the flange should be equipped with stiffening plates, and the spacing should not be greater than 450 mm. The reinforcement of organic and inorganic FRP pipes shall be made of the same materials with the same anti-corrosion performance as the pipes themselves. Sanding pipe Where can I find it? The manufacture of rectangular pipe elbows shall generally adopt concentric arc elbows with the curvature radius of the length inside and outside the plane. When other forms of elbow are used, and the plane length is more than 500 mm, the elbow deflector shall be set.