Many people don't know much about spiral tube. In fact wear-resisting Acid and alkali resistant rubber hose It is very extensive. Spiral air duct is mainly used to connect the two places for ventilation. Spiral air ducts (stainless steel and galvanized iron sheet) are widely used in the market. Spiral air duct market is generally divided into three categories according to material: galvanized spiral air duct, stainless steel spiral air duct and composite spiral air duct. Among them, the stainless steel air duct has good quality and strong applicability, but its price is high. The return air duct of purification system, central air conditioning ventilation duct, industrial air supply and exhaust duct, environmental protection system suction and exhaust duct, mine gas drainage duct, mine coating duct, etc. The spiral duct is first used for ventilation and cooling, which belongs to the category of air duct. It is named according to its purpose, but it can also be used in other places, even for drainage, drainage or as a container, which cannot be called a pipe. Named according to the structure, it should be called spiral grooved thin-walled tube, because it is mainly made of metal, also called spiral grooved metal tube. According to the material name, there may be several names: galvanized (any zinc) (galvanized) (iron), spiral pipe, stainless steel spiral pipe (stainless steel acid resistant steel), aluminum (aluminum) spiral pipe, or in order to distinguish from the existing acid resistant stainless steel pipe, Acid and alkali resistant rubber hose company It can be called ultra-thin stainless steel pipe, because it can use 0.3mm or even thinner to roll stainless steel strip.

the north sea Acid and alkali resistant rubber hose The structure is composed of liquid resistant synthetic rubber inner rubber layer, medium rubber layer, I or II or III steel wire braid reinforcement layer, and weather resistant synthetic rubber outer rubber layer. Sand pumping hose features: 1. Sand pumping hose is made of special synthetic rubber, which has excellent oil resistance, heat resistance and aging resistance. 2. The rubber hose has high bearing pressure and excellent pulse performance. 3. The pipe body is tightly combined, soft to use, and has little deformation under pressure. 4. Sand pumping hose has excellent bending resistance and fatigue resistance. 5. The sand pumping hose is long, φ 20 meters above 32, φ Below 25 meters, it can reach 10 meters or even 100 meters. Sand pumping hose parameters: 1. The inner wall of nylon cord hose is smooth and has little friction. Reinforcing layer: high-strength synthetic wire, spiral winding of steel wire and iron wire (sand suction pipe) 2 wear-resisting Acid and alkali resistant rubber hose Flange connection (ANSI150 standard flange) 3. Nominal pressure: 20BAR4, temperature: - 50 ℃ -+95 ℃ 5. Working pressure of sand suction hose and mud discharge pipe: positive pressure: 10kg; Test pressure: working negative pressure of 15kg steel ring sand suction hose: ≥ 15kg sand suction hose has strong flexibility, which is mainly used as the sand pump sand discharge pipe to connect the sand transport pipe and sand pump, as well as the pipe connection bend.

Many people have never understood wear-resisting Acid and alkali resistant rubber hose It is better to use cast iron or rubber lining plate, so today I will give you a detailed analysis. The lining plate of the ball mill can tell you for sure that it is better to use rubber lining plate, which is also a trend for rubber lining plate to replace manganese steel lining plate. The rubber lining plate has many advantages that can not be achieved by manganese steel lining plates such as cast iron, so it has more advantages. One of the advantages of using cast iron or rubber liner for ball mill liner is that the noise of rubber liner is lower. In the process of grinding the rubber lining plate with materials, the noise is lower because it is not directly rubbed. Moreover, the rubber lining plate can throw the steel ball up for the second time to form the second grinding of materials, which makes the grinding of materials more thorough and the grinding fineness more uniform with good effect. In addition, the rubber lining plate can reduce the noise by an average of 30 dB compared with the noise of the cast iron lining plate, making it acceptable. Another important reason is energy saving. Energy consumption is an unavoidable problem for users of ball mills, because the cast iron lining plate is heavy in quality, Acid and alkali resistant rubber hose company Therefore, when the motor drives the lining plate, it will consume a lot of power. The rubber used by the rubber lining plate itself is light, so the electric energy consumed by the motor when driving is very small, which can be more than 10000 yuan of electric energy a year.

Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. the north sea Acid and alkali resistant rubber hose It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Acid and alkali resistant rubber hose company The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.

With the rapid development of the national economy and the continuous improvement of the technical level, almost all walks of life need to do exhaust ventilation systems, the north sea Acid and alkali resistant rubber hose What are the advantages worth pursuing? 1. The welding method is unique. It adopts a new low temperature welding form, which does not damage the galvanized layer of the product. The welding spot is firm, the weld seam is beautiful, and the sealing is good. After welding, no treatment is required for the weld seam. 2. The manufacture of mechanically formed air duct makes the high-quality galvanized sheet not damaged, and the galvanized layer not damaged, thus prolonging the service life. 3. The specification is uniform and the size is standard, which ensures that the inner wall of the pipeline is flat and smooth, so that it is easy to clean and the material transportation is smooth. 4. The self forming flange can make the pipe material uniform, no longer use angle steel flange, and reduce the pipe weight by more than 20%, so the load bearing capacity of the building can be greatly reduced, thus reducing the overall cost of the building. 5. Enhance the beautiful pipeline, beautiful appearance, exquisite structure, smooth lines, superior performance, and the installation of exposed air ducts, especially suitable for this product. 6. Typical round air pipe fittings are generally 3-6 meters long and rectangular pipe fittings are 1-1.5 meters long, reducing the connection points of pipe fittings and minimizing the leakage at the joint of pipe fittings. 7. The pipe fittings, joints and spare parts made by mechanized assembly line all have standard sealing rings. As they are produced in a standardized and factory way, they have better air tightness. 8. Mechanically formed compression ribs and stiffeners can improve the strength of the pipe wall, save material thickness and reduce costs. The thickness of the seam of the spiral pipe is 4 times that of the pipe body, which makes the pipe very rigid and has the best pressure bearing performance, especially the negative pressure. 9. Scientific joint and seaming methods can ensure smooth pipeline gas without affecting pipeline flow diameter. Therefore, mechanized assembly line production improves production efficiency and effectively shortens delivery cycle. Advanced computer process control program blanking, production, Acid and alkali resistant rubber hose company It ensures the dimensional accuracy of pipeline components, thus ensuring fast and convenient installation and construction, and improving work efficiency and economic benefits.