Whether in the process of purchase or use, wear-resisting Large diameter suction pipe The quality of all needs to be checked regularly. During the inspection, the following items should be noted. 1. Standard size and actual error of high-pressure rubber hose: because the inner diameter and outer diameter of high-pressure sand blasting pipe and the outer diameter of the skeleton layer will shake, if the shaking amplitude exceeds the allowable limit, the balance of the buckling amount of the sand blasting pipe joint cannot be guaranteed, and the quality of the sand blasting pipe assembly cannot be guaranteed. Therefore, for the sand blasting pipe selected for the production of sand blasting pipe assembly, it is necessary to strictly check whether the inner diameter and outer diameter of the skeleton layer meet the requirements, and the requirements for the outer diameter error can be appropriately relaxed. 2. Wall thickness error of high-pressure hose: due to the local pain of the rubber layer in the high-pressure sandblasting pipe and the influence of the overlapping width of the rubber layer in the high-pressure sandblasting pipe quality inspection center between the skeleton layers, the wall thickness error of the sandblasting pipe may be too large. If the wall thickness error exceeds the allowable range, it will affect the tightness and pull-out strength of the connector, and even cause some deflection (tilting head) of the hose assembly connector. Quality inspection of high-pressure sand blasting pipe Therefore, the wall thickness error of sand blasting pipe should be strictly controlled. Generally, the rubber hose with wall thickness error exceeding 0.5mm shall be selected stably. 3. Adhesion between each layer of high-pressure rubber hose: high-quality high-pressure sand blasting pipe shall have prominent integrity, that is, the quality inspection of high-pressure sand blasting pipe shall have high adhesion between each structural layer, and the adhesion between each adhesive layer shall become an integrity. Only in this way can we meet various technical requirements in the process of joint installation and fastening, and only in this way can we ensure the quality inspection requirements of high-pressure sand blasting pipes for sand blasting pipe assembly. Therefore, Large diameter suction pipe company It is necessary to control the adhesive force between each layer of the rubber hose not lower than that specified in the technical standard, and the rubber hose with high adhesive force shall be selected as far as possible to produce the rubber hose assembly.
I, wear-resisting Large diameter suction pipe Quantitative display of quality. In the evaluation plan prepared by the Ministry of Health and Social Insurance for the medical and health system, some indicators were put forward for the service quality of the hospital, such as the number of deaths before and after the operation, the number of unplanned rehospitalization, the infection rate of patients in the hospital, and the immunization rate. It can be seen that the quantification of quality is to reflect the quality of things through a series of quantitative analysis and synthesis. Sand blasting hose enterprises use public opinion polls to measure benefits and service quality. Since the purpose of administrative activities is to meet the needs of society or the public, the best way to measure the social effect and quality is to face the service objects, understand their evaluation and their satisfaction. Although popular, public opinion polls also have limitations, such as high cost, which is difficult to be accurate and reliable due to the influence of public judgment. In addition, the satisfaction of beneficiaries does not answer the question - is this service provided to those who need it most? III, Large diameter suction pipe company Administrative departments and public service institutions with single business nature. For those departments that have applied the quality assurance system, their performance evaluation only pays attention to efficiency and economy.
Although fire Shangrao Large diameter suction pipe Explosion proof pipe) can be compressed and stretched, but if the installation position is incorrect, it will break quickly and reduce the service life. The sandblasting hose can be installed horizontally, vertically or obliquely. The most ideal condition is vertical installation. At the same time, avoid installing near the wheel, and install baffle if necessary. Generally speaking, the flame spraying metal sand blasting hose (explosion-proof pipe) can be divided into three lengths: the first is the compression length, that is, the length of the sand blasting hose when it is compressed to the limit position; The second is the installation length, that is, the length of the sandblasting hose when it is in the middle of half of the maximum displacement. The third type is the stretching length, that is, the length when the sandblasting hose is stretched to the maximum limit. When installing the sandblasting hose, the sandblasting hose should be in the middle position, which is called the installation length. When installed at this position, the sandblasting hose can move in two directions when bearing axial load. Otherwise, if it can only move in one direction, its strength will be affected and its service life will be reduced. In the actual installation process, considering that measuring the length of the sandblasting hose with a ruler according to the calculation results may affect the production efficiency, some foreign manufacturers directly install the ruler on the sandblasting hose, and cut the ruler after installation. From the structural point of view, the metal flame spraying metal sandblasting hose (explosion-proof pipe) is composed of strip and tube parts, which can form annular flame spraying metal sandblasting hose bellows and spiral flame spraying metal sandblasting hose bellows. Large diameter suction pipe company Just because the corrugated pipe of the fire sprinkler metal sandblasting hose formed by this article always has a certain length of brazing or welding buckles and fire sprinkler metal sandblasting hose joints, the residues of the working medium often accumulate in these places, and the cleaning test and mechanical impurities in the working medium will deposit down to pollute the inner cavity. Therefore, its use reliability is relatively poor.
wear-resisting Large diameter suction pipe The inner rubber layer of（ ф 0.3-2.0 reinforcement layer) is the skeleton material that plays the role of reinforcement. What should be paid attention to when storing the wear-resistant sandblasting pipe. 1. The wear-resistant sandblasting pipe should be stored as loose as possible. Generally, rubber hoses with inner diameter less than 76 mm can be wound and stored. 2. During the storage of wear-resistant sand blasting pipe, it is strictly prohibited to stack heavy objects on the pipe body to prevent external extrusion and damage. 3. During the storage of wear-resistant sand blasting pipe, do not contact with acid, alkali, oil, organic solvent or other corrosive liquids and gases, and the heat release should start from 1m away. 4. The storage period of wear-resistant sand blasting pipe shall not exceed 2 years, and it shall be used by the first person to prevent the quality of rubber pipe from being affected by long-term storage. 5. When wear-resistant sand blasting pipes need to be temporarily stored in the open air, the site should be flat and the rubber pipe should be laid flat. The upper cover should be placed under the rubber pipe and no heavy objects should be stacked. At the same time, the hose shall not contact the heat source. 6. The storage place of the upper and lower rubber pipes in the well shall be kept clean and ventilated, and the relative humidity shall be 80. The temperature of the storage place shall be kept between - 15 ℃ and 40 ℃, and the rubber pipe shall be protected from direct sunlight and water spray. 7. When storing wear-resistant sand blasting pipe, Large diameter suction pipe company Both ends of the hose shall be sealed firmly to prevent sundries from entering the hose. 8. When the wear-resistant sand blasting pipe is stored, it should be placed separately according to different varieties and specifications, not mixed, and hang the management board. 9. In order to prevent the pipes from being pressed and deformed during storage, they should not be stacked too high, and the stacking height should not exceed 1.5m. It also requires rubber hoses to be "stacked" frequently during storage, at least once a quarter.
Prof. Weina, University of New South Wales, Australia? Sahajwara has developed a new method of using waste rubber and plastic for steel production - polymer injection process. Shangrao Large diameter suction pipe It can not only greatly reduce the environmental pollution caused by waste rubber and waste plastics, but also effectively reduce the cost of steel production. Waste rubber and plastic contain a lot of carbon. Waste rubber and plastic are put into the electric arc furnace as substitutes for carbon element. The carbon originally locked in the waste plastic hose will react at ultra-high temperature and burn with coal to become clean fuel, thus reducing greenhouse gas emissions, At the same time, it also alleviates the environmental pollution caused by using them as landfill. The advantage of polymer injection process is that by injecting polymer and coke or anthracite rubber tube mixture, the volume of slag can be increased and the foaming degree can be increased, which can extend the arc length, increase the heat transfer from the arc to steel, reduce the heat loss through the slag and side walls, and thus improve the power efficiency. This reduces power consumption by about 3%. For every 1 ton of steel, about 24% of the cost comes from the cost of electricity. After polymer injection technology is adopted, each furnace of steel is, Large diameter suction pipe company The average total amount of carbon injected can be reduced by 10%~20%. In addition, the potential price of polymer is lower than that of coke, and the total cost of carbon injection can be saved by 15%~35%.
If conditions permit, secondary vulcanization shall be adopted, wear-resisting Large diameter suction pipe Effectively remove the odor generated during the consumption of odorless hose. Pay attention to the volatilization of various ingredients in the odorless hose formula. When the odorless hose is consumed, in addition to paying special attention to the raw materials and vulcanization process of the reclaimed rubber, pay attention to the selection of various ingredients and whether they will volatilize in the vulcanization process. The volatilization of vulcanizing agent, accelerator and antioxidant will produce a great smell. It is very important to accurately determine the length of the required rubber sand blasting pipe by using the rubber sand blasting pipe. It shall also be checked whether the use conditions of the rubber sand blasting pipe meet the requirements of the selected rubber sand blasting pipe. It should be ensured that the rubber sand blasting pipe you will use is the most suitable one. The working pressure and suction should be carefully determined. Special attention shall be paid to the test standard pressure change or pressure peak of wear-resistant sand blasting pipe. Exceeding the promised maximum value will greatly shorten the service life of the rubber sand blasting pipe. Both ends of the rubber sand blasting pipe cannot be continuously immersed in the transported material. If the bending radius of the rubber sand blasting pipe is less than the minimum value, Shangrao Large diameter suction pipe Its service life will be greatly shortened. Therefore, before installation, it is recommended that you consult the application of information, especially the information about the bending radius of the rubber sand blasting pipe. Protection and cleaning of rubber sand blasting hose: it is recommended to empty the hose after use. Clean if necessary. Inspection: After each use, the rubber sand blasting pipe must be inspected to ensure that it does not show structural damage.
