The reason why welded air duct has become the favorite of the market, Daqing Steel wire/transparent tube Compared with the air duct made of traditional materials, it has obvious advantages in technology, energy conservation, environmental protection and economy. This product has been inspected, tested and proved by the National Building Materials Testing Center, the National Fire Building Materials Quality Supervision and Inspection Center, the National Air Conditioning Equipment Quality Supervision and Inspection Center, the National Non ferrous Metal Quality Supervision and Inspection Center and other relevant authorities, In addition, no smoke is generated in the fire, and the smoke density is only 4, which is 10 to 20 times that of other organic foam materials. In modern buildings, central air conditioning is very common, and ventilation ducts are an important part of the central air conditioning system. According to statistics, China's annual demand is about 100 million square meters, reaching 20 billion yuan. Among all kinds of air ducts, welded air ducts stand out for their unique excellent performance and cost performance, and are becoming the new favorite in the central air-conditioning market. The manufacturing of welded air ducts is highly automated and the production speed is very fast. Ordinary air ducts can produce 20~40 meters per minute. Due to the low price of the raw material galvanized strip steel compared with the whole galvanized steel sheet, and its factory production and specification standardization, the cost is lower than that of rectangular air ducts; In addition, the total cost is low due to the less demand for supports and hangers and the less installation work. Since the four corners of rectangular air duct are prone to turbulence, Steel wire/transparent tube Price The effective flow area is reduced. The technology of welded air duct is very close to the international level; In terms of supporting services, more and more enterprises like this company provide high standard services. If there are any suggestions, we hope to see more and more enterprises with a sense of mission for the development of the industry.
Daqing Steel wire/transparent tube The entry threshold is low, the industry market is mixed, and small enterprises with small scale, lack of core competitiveness and low technical level can be seen everywhere. Most of these enterprises lack brand awareness, and there are many brand names and unlicensed products. It is difficult to form enterprise influence through brands, and it is more difficult to improve product added value through brands. If the metal hose wants to take the road of high-end, it must improve both inside and outside. A good brand image promotion and influence building can certainly provide a strong driving force for the development of enterprises, but the root of this driving force lies in the high quality of the metal hose products themselves. Tongfeng Metal Hose said that in the future, domestic metal hose products will focus on high precision, high efficiency, high firmness, multi-function, multi specification, multi variety standardization, serialization and generalization to show their characteristics. One of the main reasons why China's metal hoses have been in the low-end state for a long time is the lack of independent research and development of products. On the one hand, the homogenization competition is serious. In order to win consumers, metal hose enterprises have long focused on low-cost competition and low price shopping. As a result, many enterprises only focus on the production and marketing of low-end products, ignoring the upgrading and innovation of product technology. on the other hand, Steel wire/transparent tube Price ZHUANLI's weak awareness of protection and the serious phenomenon of technology plagiarism and infringement in the industry make the technology cost invested by many enterprises more than worth the cost, which has seriously hit the enthusiasm of metal hose enterprises for innovation.
high quality Steel wire/transparent tube 1. During the molding of rubber products, the cohesive force of the elastomer cannot be eliminated due to the large pressure pressing. During the molding and mold release, extremely unstable shrinkage (the shrinkage rate of rubber varies due to different rubber types) often occurs. It must take a period of time before it can be gentle and stable. Therefore, at the beginning of the design of a rubber product, no matter the formula or the mold, it is necessary to carefully calculate the matching. If not, it is easy to cause dimensional instability of the product, resulting in low product quality. 2. Rubber belongs to thermosetting elastomer, while plastic belongs to thermosetting elastomer. Due to different sulfide types, the temperature range of rubber molding and curing is quite different, even affected by climate change and indoor temperature and humidity. Therefore, the production conditions of rubber products need to be properly adjusted at any time. If not, there may be differences in product quality. 3. The rubber product is the rubber mixture made from rubber raw materials after mixing in the internal mixer as the raw material. The formula is designed according to the characteristics of the required rubber products during mixing, and the required product hardness is determined. The product is molded by the rubber plate vulcanizer. After the product is formed, flash processing shall be carried out to make the product surface smooth without burrs. 4. The aging test of rubber products belongs to the category of aging test. Rubber aging refers to the phenomenon that the performance and structure of rubber and products are changed due to the combined effect of internal and external factors in the process of processing, storage and use, thus losing their use value. Steel wire/transparent tube Price It is characterized by cracking, tackiness, hardening, softening, chalking, discoloration, mildew, etc. The following conditions shall be met when the ball mill uses the rubber lining plate: 1. The hardness of the ground material. The iron base alloy is similar to the rubber lining plate for materials below medium hardness, and the rubber lining plate is superior for materials above medium hardness. 2. The temperature of rubber lining plate is generally 70 ℃ - 90 ℃, and it can reach 110-130 ℃ under special circumstances. The temperature should be lower during dry grinding. 3. Feed size. Generally, the ball mill shall be more than 20-25mm; For the autogenous mill, the feeding particle size can be larger because no steel ball is added.
Daqing Steel wire/transparent tube Prevention of vibration and noise during installation: the prevention of vibration and noise during installation is a key point in the installation process. The prevention of vibration and noise of spiral air duct during installation is mainly from the following aspects: 1. The fan and spiral air duct are connected by hose, and the hose at the suction inlet of the fan shall be installed with appropriate tightness, Avoid noise and vibration caused by reducing the area of air inlet and outlet due to loose soft connection. 2. The spiral air duct shall be made, installed and connected with the components. The connection shall be tight to reduce the gap and avoid air leakage noise. 3 In order to prevent the spiral air duct from vibration, fixed supports shall be installed at the turning of each system spiral air duct and at the connection with the ventilator and the air outlet for shock absorption. 4 The vibration damping device shall be set according to the design requirements or construction specifications during fan installation. Air leakage rate test of spiral air duct After the installation of spiral air duct, air leakage rate test is required. According to the specifications, the air leakage rate test of spiral air duct adopts the combination of light leakage legality and quantitative air leakage rate test. The light leakage method is suitable for the tightness test of medium and low pressure systems; The air leakage rate test is suitable for sampling inspection of medium pressure system and full detection of high pressure system. Light leak detection of spiral air duct Light leak detection is a qualitative method to detect the tightness of the spiral air duct of the system by using the strong penetration of light to holes. The test method is to use a bulb with protective cover whose voltage is not higher than 36V and power is more than 100W in the spiral air duct on a certain length of spiral air duct in dark environment, and slowly move from one end of the spiral air duct to the other end. If light can be observed outside the spiral air duct during the test, it indicates that there is a leak point in the spiral air duct, and repair the leak point of the spiral air duct. Steel wire/transparent tube Price The light leak detection method of the low-pressure system adopts the method of subsection detection and summary analysis. The spiral air duct of the tested system is not allowed to have multiple obvious light leaks in the form of slits. The spiral air duct of the low-pressure system has no more than two light leak points every 10 meters, and the average joint of 100 meters is no more than 16; For every 10 joints of spiral air duct of medium pressure system, no more than 1 light leak point, and no more than 8 joints per 100 meters are qualified.
Daqing high quality In places that must be crossed or may rub with the mechanical surface when working, hose clamps or springs and other protective devices should be used to prevent the outer layer of the sandblasting hose from being damaged. Sand blasting hose shall be arranged to avoid heat source as far as possible and away from the performance of engine exhaust pipe. If necessary, sleeve or protective screen can be used to prevent the hose from being heated and deteriorated. When the sand blasting hose must be bent, the bending radius should not be too small, and should be greater than 9 times the outer diameter. There should be a straight line section greater than 2 times the outer diameter of the pipe at the joint between the rubber hose and the joint. How high-quality the products and equipment we use are, it is inevitable that there will be some large and small failures in the process of using them, which will more or less have a certain impact on our work. Just like the use of sandblasting hose, there are traces of its outer adhesive seam, problems must be solved, For this, we explained the following solutions: First, the used water cloth should be used according to the original elastic edge of the water cloth when it is reused. 2： When we wrap the water cloth around the seam of the sandblasting hose, we should apply sufficient and uniform pressure to the pipe body. 3. The water cloth with different widths should be selected according to the size of the outer diameter of the wrapped sandblasting hose (for hose with an outer diameter of less than 30mm, the width of the water cloth should not exceed 90mm). The overlapping width of the water cloth should be 3/5-2/3 of the width of the water cloth.
