Whether in the process of purchase or use, high quality Rubber hose The quality of all needs to be checked regularly. During the inspection, the following items should be noted. 1. Standard size and actual error of high-pressure rubber hose: because the inner diameter and outer diameter of high-pressure sand blasting pipe and the outer diameter of the skeleton layer will shake, if the shaking amplitude exceeds the allowable limit, the balance of the buckling amount of the sand blasting pipe joint cannot be guaranteed, and the quality of the sand blasting pipe assembly cannot be guaranteed. Therefore, for the sand blasting pipe selected for the production of sand blasting pipe assembly, it is necessary to strictly check whether the inner diameter and outer diameter of the skeleton layer meet the requirements, and the requirements for the outer diameter error can be appropriately relaxed. 2. Wall thickness error of high-pressure hose: due to the local pain of the rubber layer in the high-pressure sandblasting pipe and the influence of the overlapping width of the rubber layer of the high-pressure sandblasting pipe quality inspection center between the skeleton layers, the wall thickness error of the sandblasting pipe may be too large. If the wall thickness error exceeds the allowable range, it will affect the tightness and pull-out strength of the connector, and even cause some deflection (tilting head) of the hose assembly connector. Quality inspection of high-pressure sand blasting pipe Therefore, the wall thickness error of sand blasting pipe should be strictly controlled. Generally, the rubber hose with wall thickness error exceeding 0.5mm shall be selected stably. 3. Adhesion between each layer of high-pressure rubber hose: high-quality high-pressure sand blasting pipe shall have prominent integrity, that is, the quality inspection of high-pressure sand blasting pipe shall have high adhesion between each structural layer, and the adhesion between each adhesive layer shall become an integrity. Only in this way can we meet various technical requirements in the process of joint installation and fastening, and only in this way can we ensure the quality inspection requirements of high-pressure sand blasting pipes for sand blasting pipe assembly. Therefore, Rubber hose Price It is necessary to control the adhesive force between each layer of the rubber hose not lower than that specified in the technical standard, and the rubber hose with high adhesive force shall be selected as far as possible to produce the rubber hose assembly.

Beijing Rubber hose The break of the sandblasting hose usually refers to the appearance and change of the crack of the sandblasting hose. The sandblasting hose has one or more cracks, but the cracks are neat. Another is that the internal bending cracks at the crack of the sandblasting hose are neat. The causes of different errors are different, and the treatment methods are also different. Therefore, in the process of using or protecting the sandblasting hose, the sandblasting hose should not be subject to changing torque. When installing the sandblasting hose, try to keep the axis of the two joints on the same plane to avoid twisting the sandblasting hose in use. Therefore, be careful with the application, and try not to make the sandblasting hose change excessively to avoid consumption. Sand blasting hose plays a very important role in the industry. Its inner rubber layer is added with carbon black, which can effectively eliminate static electricity and directly contact with compressed air and abrasives. The requirement for wear resistance is quite high. Once worn through, the reinforcement layer will be exposed, and the sand blasting hose will burst. The reinforcing layer of sandblasting hose is a pressure resistant layer, so high quality Rubber hose The material and layout of the reinforcement layer directly determine the pressure rating of the sandblasting hose. There are two common enhancement layers: cloth clip enhancement layer and surround enhancement layer. The sand blasting hose with an inner diameter of 50mm or more is mostly used in the construction occasions where the sand blasting pipe needs to be extended to reduce the pressure loss in the sand blasting hose and ensure the normal operation of shot blasting.

Beijing Rubber hose It is widely used in mining, chemical industry, construction and iron and steel fields. At present, 90% of ball mills, rod mills and moistening mills on the market still use manganese steel cylinder liners, and the manganese steel material consumed on liners alone every year is more than one million tons. The emergence of rubber liners is favored by many big customers in the ball mill field. What are the indexes that affect the rubber lining plate of the ball mill? 1. Conditions of ball mill use scenario The feeding particle size of ore also plays an important role, so a good ball mill rubber lining plate will be designed according to the size of the customer's mill, feeding particle size, and steel ball diameter. Select the rubber formula suitable for customers, and carry out mapping, design, testing and processing. 2. Rubber formula and processing technology: The rubber material and formula directly affect the performance of the rubber lining plate of the ball mill. Wear resistance is a key factor. It is impossible to determine how long its service life is because of the impact of industrial and mining conditions. The second is corrosion resistance. This is the characteristic of the formula, so even if the appearance is the same, the performance is an advantage. Do not buy for cheap. 3. Regular maintenance: everyone knows that the rubber lining plate of the ball mill is fixed to the cylinder by means of T-bolts, so it is also very important to regularly check the tightness of the bolts and the wear of the rubber strips inside the cylinder. In order to avoid damaging the rubber lining plate of the cylinder and the cylinder of the ball mill when the lifting strip is worn out, the gain is not worth the loss. Rubber hose Price One of the advantages of the manganese steel lining plate is that the replacement is simple and only needs two people to operate, and it can be replaced wherever it is broken. This is an advantage that the manganese steel lining plate does not have.

Many people have never understood high quality Rubber hose It is better to use cast iron or rubber lining plate, so today I will give you a detailed analysis. The lining plate of the ball mill can tell you for sure that it is better to use rubber lining plate, which is also a trend for rubber lining plate to replace manganese steel lining plate. The rubber lining plate has many advantages that can not be achieved by manganese steel lining plates such as cast iron, so it has more advantages. One of the advantages of using cast iron or rubber liner for ball mill liner is that the noise of rubber liner is lower. In the process of grinding the rubber lining plate with materials, the noise is lower because it is not directly rubbed. Moreover, the rubber lining plate can throw the steel ball up for the second time to form the second grinding of materials, which makes the grinding of materials more thorough and the grinding fineness more uniform with good effect. In addition, the rubber lining plate can reduce the noise by an average of 30 dB compared with the noise of the cast iron lining plate, making it acceptable. Another important reason is energy saving. Energy consumption is an unavoidable problem for users of ball mills, because the cast iron lining plate is heavy in quality, Rubber hose Price Therefore, when the motor drives the lining plate, it will consume a lot of power. The rubber used by the rubber lining plate itself is light, so the electric energy consumed by the motor when driving is very small, which can be more than 10000 yuan of electric energy a year.

Beijing Rubber hose Structure type of product: sand blasting hose is mainly composed of liquid resistant inner rubber layer, middle rubber layer, 2 or 4 or 6 layers of steel wire winding reinforcement layer and outer rubber layer. The inner rubber layer has the function of bearing the pressure of the transmission medium and protecting the steel wire from erosion, the outer rubber layer protects the steel wire from damage, and the steel wire (0.3-2.0 steel wire) layer is the reinforced skeleton material. Application of sandblasting hose products: high-pressure sandblasting hose is mainly used for mining hydraulic support and oil field exploitation, and is suitable for engineering construction, lifting and transportation, metallurgical forging, mining equipment, ships, injection molding machinery, agricultural machinery, various machine tools, and mechanical and automatic hydraulic systems in various industrial sectors to transport petroleum base with a certain pressure (higher pressure) and temperature. (such as mineral oil, soluble oil, hydraulic oil, fuel oil, lubricating oil) and water-based liquid (such as emulsion, oil-water emulsion, water). And liquid transmission. The working withstand voltage can reach 70-100 MPa. The company's sand blasting hose standards refer to national standards/T10544-03, DIN 20023, and SaE100 R9-13. Rubber hose Price Made of special synthetic rubber, it has excellent oil resistance, heat resistance and aging resistance. The rubber hose has high bearing pressure and superior pulse performance. The tube body is tightly combined, soft to use, and has little compression deformation. The hose has excellent bending resistance and fatigue resistance. The sandblasting hose is 20m long and can be made within 50m as required.

Beijing high quality In places that must be crossed or may rub with the mechanical surface when working, hose clamps or springs and other protective devices should be used to prevent the outer layer of the sandblasting hose from being damaged. Sand blasting hose shall be arranged to avoid heat source as far as possible and away from the performance of engine exhaust pipe. If necessary, sleeve or protective screen can be used to prevent the hose from being heated and deteriorated. When the sand blasting hose must be bent, the bending radius should not be too small, and should be greater than 9 times the outer diameter. There should be a straight line section greater than 2 times the outer diameter of the pipe at the joint between the rubber hose and the joint. How high-quality the products and equipment we use are, it is inevitable that there will be some large and small failures in the process of using them, which will more or less have a certain impact on our work. Just like the use of sandblasting hose, there are traces of its outer adhesive seam, problems must be solved, For this, we explained the following solutions: First, the used water cloth should be used according to the original elastic edge of the water cloth when it is reused. 2： When we wrap the water cloth around the seam of the sandblasting hose, we should apply sufficient and uniform pressure to the pipe body. 3. The water cloth with different widths should be selected according to the size of the outer diameter of the wrapped sandblasting hose (for hose with an outer diameter of less than 30mm, the width of the water cloth should not exceed 90mm). The overlapping width of the water cloth should be 3/5-2/3 of the width of the water cloth.