As production Sand suction hose As an important part of sand blasting machinery, its safety plays a vital role in the safety of equipment operation. The following will briefly analyze the precautions in the use of high-pressure sandblasting pipe: I. Pipe inner diameter: inner diameter of high-pressure sandblasting pipe. 2、 Attention shall be paid to the following items in the use and design of high-pressure sandblasting pipe: 1. The bending radius of high-pressure sandblasting pipe shall not be too small, and generally shall not be less than the value specified in the assembly technology of high-pressure sandblasting pipe. The joint between the high-pressure sandblasting pipe assembly and the pipe joint shall have a straight section, and its length shall not be less than twice the outer diameter of the pipe. 2. The length of high-pressure rubber hose assembly shall consider that the high-pressure rubber hose will shrink and deform after introducing pressure oil. Generally speaking, the shrinkage rate is 3~4 times of the pipe length. When installing the high-pressure rubber hose assembly, it is not allowed to bear tension. 3. During installation, the high-pressure sandblasting pipe assembly shall be free from torsional deformation. Sand suction hose company The connecting shaft of shall be placed in the moving plane as far as possible to avoid damaging the high-pressure sandblasting pipe when both ends move with each other. 4. High pressure resistant sand blasting pipe shall avoid contact and friction with mechanical sharp corners to avoid damaging the pipe. Safety measures: to ensure the safe and reliable use of high-pressure sandblasting pipe assembly.
Shenyang Sand suction hose With the continuous updating of technology, the products are also developing in the continuous updating. At present, the inspection requirements of rubber hose are also improved compared with the previous ones. The inspection index of ultra-high pressure hose shall meet the following index requirements according to the requirements of the Safety Code for High Pressure Water Jet Cleaning Operation: 1) The bursting pressure shall be more than 2.5 times of the working pressure. 2) The test pressure shall be 1.5 times of the working pressure, and the pressure shall be kept for more than 2 minutes without damage. 3) Pulse pressure shall be within the range from zero to working pressure, and 50000 pressure pulses shall be free of damage; The pulse frequency is 15 times/min when the working pressure is 1000-2800bar, and 110 times/min when the pressure is above 2800bar. Since high-pressure cleaning machine has been widely used in all walks of life, and the working condition of high-pressure hose is relatively the worst, we must pay attention to the quality when selecting high-pressure hose, so as to avoid unnecessary safety accidents. Sand suction hose company The development of rubber hose can not be separated from cooperation, R&D and innovation can not be separated from communication, and the inspection requirements of rubber hose have been improved compared with the previous ones. The storage site shall be free of ozone, heat source and equipment generating electromagnetic field. The coiled hoses or hose assemblies shall be stored horizontally, and the stacking height shall be limited to the extent that the products at the bottom will not produce permanent deformation.
Shenyang Sand suction hose It is used for transportation, construction and other operating equipment. Incorrect operation and incorrect environment may affect the normal use of steel braided sandblasting pipe. What specific factors will affect the normal use of steel braided sand blasting pipe? The quality will definitely affect the use effect. The poor quality is actually related to the selected raw materials. Some raw materials are of high quality, and the quality of steel braided sandblasting pipes produced is also very good. However, if the steel braided sand blasting pipe is made of inferior plastic, the quality is very poor, which also affects the use effect. The use environment affects the use effect. Anti static steel braided sand blasting pipe is usually used in industry. Because these products are very common, the demand is also large. However, people do not pay attention to the use environment. If used in strong acid and alkali environment, steel braided sand blasting pipe will naturally corrode. Or if used in a relatively high temperature area, the steel braided sandblasting pipe may melt. Anti static steel braided sand blasting pipe will also affect the use effect. In the eyes of most users, the greater the degree, the better the nature. So if you choose a good one, users can use it with confidence. Understanding and avoiding the wrong use of high-pressure pipeline can reduce the possibility of high-pressure pipeline failure. The following brief introduction will help you. 1. Frequent and serious pressure shock: high-pressure pipeline burst is generally not caused by excessive static pressure, but is related to the severity and frequency of pressure shock. During the operation of construction machinery, the sudden increase or decrease of oil pressure in the high-pressure pipe will occur repeatedly, which will cause frequent pressure shocks to the oil pipe, leading to the aggravation of oil seal damage at various parts, blistering and cracking of rubber hose, and loosening and leakage of pipe joints. Therefore, during operation, the valve rod shall not be pulled too hard, but must be pulled gently. 2. The use temperature of oil is too high: during the operation of construction machinery, due to the power loss of the hydraulic system, the oil will rise, and the external temperature (especially in summer) will lead to a sharp rise in the oil temperature. production Sand suction hose company The higher the oil temperature is, the easier the rubber is to age, the worse the elasticity is, the lower the strength and sealing performance are, and the high-pressure pipe will burst rapidly. Therefore, when the temperature rise of the hydraulic system is too high or too fast during operation, the causes should be found out and eliminated in time. For summer operation, especially continuous operation, necessary cooling measures shall be taken.
production Sand suction hose 1. During the molding of rubber products, the cohesive force of the elastomer cannot be eliminated due to the large pressure pressing. During the molding and mold release, extremely unstable shrinkage (the shrinkage rate of rubber varies due to different rubber types) often occurs. It must take a period of time before it can be gentle and stable. Therefore, at the beginning of the design of a rubber product, no matter the formula or the mold, it is necessary to carefully calculate the matching. If not, it is easy to cause dimensional instability of the product, resulting in low product quality. 2. Rubber belongs to thermosetting elastomer, while plastic belongs to thermosetting elastomer. Due to different sulfide types, the temperature range of rubber molding and curing is quite different, even affected by climate change and indoor temperature and humidity. Therefore, the production conditions of rubber products need to be properly adjusted at any time. If not, there may be differences in product quality. 3. The rubber product is the rubber mixture made from rubber raw materials after mixing in the internal mixer as the raw material. The formula is designed according to the characteristics of the required rubber products during mixing, and the required product hardness is determined. The product is molded by the rubber plate vulcanizer. After the product is formed, flash processing shall be carried out to make the product surface smooth without burrs. 4. The aging test of rubber products belongs to the category of aging test. Rubber aging refers to the phenomenon that the performance and structure of rubber and products are changed due to the combined effect of internal and external factors in the process of processing, storage and use, thus losing their use value. Sand suction hose company It is characterized by cracking, tackiness, hardening, softening, chalking, discoloration, mildew, etc. The following conditions shall be met when the ball mill uses the rubber lining plate: 1. The hardness of the ground material. The iron base alloy is similar to the rubber lining plate for materials below medium hardness, and the rubber lining plate is superior for materials above medium hardness. 2. The temperature of rubber lining plate is generally 70 ℃ - 90 ℃, and it can reach 110-130 ℃ under special circumstances. The temperature should be lower during dry grinding. 3. Feed size. Generally, the ball mill shall be more than 20-25mm; For the autogenous mill, the feeding particle size can be larger because no steel ball is added.
Shenyang Sand suction hose It is mainly used for the transportation of liquid and gas. The use requirements of cloth clip sand blasting pipe are stricter than those of ordinary rubber hose. The so-called high voltage puts forward this requirement. The following small series will introduce the use requirements of cloth clip sandblasting pipe. According to the use characteristics of cloth clip sand blasting pipe, the larger working pressure of cloth clip sand blasting pipe is determined according to the system pressure. Each cloth clamping sand blasting pipe has a normal working pressure, and the bursting pressure of cloth clamping sand blasting pipe is 3-4 times of the larger working pressure. The higher the pressure, the higher the number of steel wire layers, and the more stringent the product production. Therefore, according to the actual pressure of the system, the higher the working pressure of the cloth clamping sand blasting pipe, the normal operation of the system can be ensured, and the appropriate cloth clamping sand blasting pipe can be selected. If the impact pressure of the system is frequent, the cloth clip sandblasting pipe with high pulse life shall be selected, and the specification and model classification of the cloth clip sandblasting pipe shall be properly improved. Temperature is also one of the factors considered by customers. Sand suction hose company The high and low temperature transition in the working environment will affect the service life and pressure bearing capacity of the rubber hose. Therefore, high-pressure rubber hoses should be used within their allowable range. For the system whose long-term operating temperature is not within its allowable range, hose sheath or special rubber hose shall be purchased.
Shenyang Sand suction hose The entry threshold is low, the industry market is mixed, and small enterprises with small scale, lack of core competitiveness and low technical level can be seen everywhere. Most of these enterprises lack brand awareness, and there are many brand names and unlicensed products. It is difficult to form enterprise influence through brands, and it is more difficult to improve product added value through brands. If the metal hose wants to take the road of high-end, it must improve both inside and outside. A good brand image promotion and influence building can certainly provide a strong driving force for the development of enterprises, but the root of this driving force lies in the high quality of the metal hose products themselves. Tongfeng Metal Hose said that in the future, domestic metal hose products will focus on high precision, high efficiency, high firmness, multi-function, multi specification, multi variety standardization, serialization and generalization to show their characteristics. One of the main reasons why China's metal hoses have been in the low-end state for a long time is the lack of independent research and development of products. On the one hand, the homogenization competition is serious. In order to win consumers, metal hose enterprises have long focused on low-cost competition and low price shopping. As a result, many enterprises only focus on the production and marketing of low-end products, ignoring the upgrading and innovation of product technology. on the other hand, Sand suction hose company ZHUANLI's weak awareness of protection and the serious phenomenon of technology plagiarism and infringement in the industry make the technology cost invested by many enterprises more than worth the cost, which has seriously hit the enthusiasm of metal hose enterprises for innovation.
