Handan Sand suction hose Also called pu steel wire pipe, ventilation pipe, dust removal pipe, dust collection pipe, dust conveying pipe, industrial powder dust collection pipe, sweeping car dust collection pipe, drilling machine dust collection pipe, woodworking dust collection pipe, collectively called dust collection pipe. Therefore, industrial food dust transportation and industrial dust transportation are used for dust collection pipe. The production process structure of copper plated steel wire dust collection pipe is to wrap the pipe wall with solid elastic copper plated steel wire spirally, and the pipe wall material is coated with copper plated steel wire with special polyether PUR. PUR material is also called PU material. The thickness of pipe wall can be 0.4mm, 0.6mm, 0.9mm, 1.2mm, 1.5mm, 1.8mm and 2.1mm, depending on the customer's needs. Such as the temperature, wear resistance, flexibility and bending, hydrolysis resistance of the dust collection pipe. It is also necessary to consider whether static electricity is generated in the process of pipe full conveying dust to avoid unnecessary dust explosion and fire. Copper plated steel wire plastic coated dust collection tube is suitable for vacuum suction of powder and particle in industrial and mining, agriculture and water conservancy, civil engineering, food, petroleum, chemical industry, health and other industries, as well as transportation of water, oil, chemical materials, food, etc. Abrasive solids such as dust, powder, fiber, chip and particle, gas and liquid environment, for dedusting and suction plant, Sand suction hose Where can I find it? Industrial vacuum cleaners, paper and textile fibers, are used as protective tubes. It is widely used in farmland irrigation, industry and mining, oil depot, sand extraction, sand blasting, food, medicine, indoor gas, powder, dust absorption and emission and other fields. This product is a substitute for PVC, rubber and metal pipes.

Handan Sand suction hose 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Sand suction hose Where can I find it? When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.

Handan wear-resisting Sand suction hose Plays an important role. In the application of different industries, according to their own needs, check the performance of the products, give proper play to the advantages of the products, and ensure the normal use of daily applications. When replacing the wear-resistant sand blasting pipe, the length of the rubber pipe, the number of steel wire layers, the shape and size of the joint should be reasonable, and the curvature of the rubber pipe should be minimized. When tightening the connecting nuts, do not tighten the rubber hose. Excessive bending and twisting will greatly reduce the service life of the rubber hose. Protective measures shall be taken for the parts liable to friction to prevent the rubber hose from bursting due to wear. What should we pay attention to when purchasing wear-resistant sandblasting pipe? Different types of wear-resistant sand blasting pipes have different working pressures. When purchasing rubber hose, you should first determine the working pressure of the system, Sand suction hose Where can I find it? Then select the equivalent working pressure of the hose. If the system is often affected by pressure, it is necessary to increase the working pressure of the hose and choose the hose with higher pulse life. The inner diameter of wear-resistant sand blasting pipe is one of the factors to be considered when selecting rubber hose. The small inner diameter will increase the flow rate of the medium, raise the temperature of the system, reduce the working efficiency, and affect the working performance of the system. The large inner diameter will increase the purchase cost. Therefore, the proper inner diameter should be selected according to the flow rate of the medium. The wear-resistant sand blasting pipe has allowable operating temperature range. The service life and pressure bearing capacity of the rubber pipe can be guaranteed only when it works at an appropriate temperature. When the operating temperature of the equipment exceeds the allowable temperature range of the rubber hose for a long time, special rubber hose shall be purchased or special protective sleeve shall be added on the wear-resistant sand blasting pipe. If the medium to be transported is special, make sure that the hose material is compatible with the medium.

Sand suction hose Where can I find it? It has become the standard configuration of the modern new ball mill, but many problems may occur during the use or installation of the rubber lining plate, which will cause the failure of the rubber lining plate of the ball mill. Here is a brief introduction to the causes of the more common failure of the rubber lining plate of the ball mill. The design and installation are not professional and reasonable. The design and installation are also common problems for many novice manufacturers. For example, the bolt holes for fixing the ball mill lining plate are square, which will cause stress concentration and fracture. Adjust the size of lining plate to control the gap between lining plates at about 8mm; The installation quality of lining plate is very important to the safe operation of ball mill. First, tighten the fixed wedge symmetrically, put the lining plate in sequence, and then use the tightening wedge to secure it; Therefore, professional installation guidance can easily avoid these problems. The reason why the rubber lining plate of the ball mill does not match the steel ball is relatively common, and it is easy for many novice manufacturers to ignore and make mistakes. During the operation of the ball mill, the rubber lining plate of the ball mill, materials and steel balls promote the normal grinding and crushing of the ball mill due to the interaction of forces. The hardness of materials is related to wear resistance, and the wear resistance increases with the increase of hardness, Handan Sand suction hose It is a pair of friction pairs, and the increase of hardness of one side will cause the wear of the other side to increase. Therefore, the high wear-resistant rubber lining plate is matched with the high wear-resistant steel ball, and the low wear-resistant rubber lining plate is matched with the low wear-resistant steel ball, so as to ensure the normal wear of the rubber lining plate of the ball mill and extend the service life of the ball mill.

If conditions permit, secondary vulcanization shall be adopted, wear-resisting Sand suction hose Effectively remove the odor generated during the consumption of odorless hose. Pay attention to the volatilization of various ingredients in the odorless hose formula. When the odorless hose is consumed, in addition to paying special attention to the raw materials and vulcanization process of the reclaimed rubber, pay attention to the selection of various ingredients and whether they will volatilize in the vulcanization process. The volatilization of vulcanizing agent, accelerator and antioxidant will produce a great smell. It is very important to accurately determine the length of the required rubber sand blasting pipe by using the rubber sand blasting pipe. It shall also be checked whether the use conditions of the rubber sand blasting pipe meet the requirements of the selected rubber sand blasting pipe. It should be ensured that the rubber sand blasting pipe you will use is the most suitable one. The working pressure and suction should be carefully determined. Special attention shall be paid to the test standard pressure change or pressure peak of wear-resistant sand blasting pipe. Exceeding the promised maximum value will greatly shorten the service life of the rubber sand blasting pipe. Both ends of the rubber sand blasting pipe cannot be continuously immersed in the transported material. If the bending radius of the rubber sand blasting pipe is less than the minimum value, Handan Sand suction hose Its service life will be greatly shortened. Therefore, before installation, it is recommended that you consult the application of information, especially the information about the bending radius of the rubber sand blasting pipe. Protection and cleaning of rubber sand blasting hose: it is recommended to empty the hose after use. Clean if necessary. Inspection: After each use, the rubber sand blasting pipe must be inspected to ensure that it does not show structural damage.