If conditions permit, secondary vulcanization shall be adopted, high quality Extruded tube Effectively remove the odor generated during the consumption of odorless hose. Pay attention to the volatilization of various ingredients in the odorless hose formula. When the odorless hose is consumed, in addition to paying special attention to the raw materials and vulcanization process of the reclaimed rubber, pay attention to the selection of various ingredients and whether they will volatilize in the vulcanization process. The volatilization of vulcanizing agent, accelerator and antioxidant will produce a great smell. It is very important to accurately determine the length of the required rubber sand blasting pipe by using the rubber sand blasting pipe. It shall also be checked whether the use conditions of the rubber sand blasting pipe meet the requirements of the selected rubber sand blasting pipe. It should be ensured that the rubber sand blasting pipe you will use is the most suitable one. The working pressure and suction should be carefully determined. Special attention shall be paid to the test standard pressure change or pressure peak of wear-resistant sand blasting pipe. Exceeding the promised maximum value will greatly shorten the service life of the rubber sand blasting pipe. Both ends of the rubber sand blasting pipe cannot be continuously immersed in the transported material. If the bending radius of the rubber sand blasting pipe is less than the minimum value, Taiyuan Extruded tube Its service life will be greatly shortened. Therefore, before installation, it is recommended that you consult the application of information, especially the information about the bending radius of the rubber sand blasting pipe. Protection and cleaning of rubber sand blasting hose: it is recommended to empty the hose after use. Clean if necessary. Inspection: After each use, the rubber sand blasting pipe must be inspected to ensure that it does not show structural damage.

high quality Extruded tube It will burst for a long time due to frequent and severe pressure shocks. This situation is usually not caused by excessive static pressure, but is related to the strength and frequency of pressure shock. During the operation of construction machinery, the oil pressure in the oil resistant hose will rise or fall repeatedly, and then it will form frequent pressure shocks to the oil pipe, causing the oil seal of each part to become more damaged, the oil resistant hose will bubble and break, and the pipe joint will become loose and leak. Therefore, in the process of operation, the valve rod should not be pulled too hard, and it needs to be gentle. The application temperature of the oil in the oil resistant rubber hose is too high, resulting in aging and bursting of the rubber hose. During the operation of construction machinery, the hydraulic system will cause the oil to become hot due to power failure, and the influence of external temperature (especially in summer) will cause the oil temperature to rise sharply. The higher the oiling temperature is, the easier the rubber hose ages, the worse the elasticity is, the lower the strength and sealing function are, and the oil resistant hose will burst quickly. Therefore, Extruded tube Price During operation, when the temperature rise of the hydraulic system is too high or too fast, the causes should be found and eliminated in time. Necessary cooling measures shall be taken for summer operation, especially continuous operation.

Taiyuan high quality In places that must be crossed or may rub with the mechanical surface when working, hose clamps or springs and other protective devices should be used to prevent the outer layer of the sandblasting hose from being damaged. Sand blasting hose shall be arranged to avoid heat source as far as possible and away from the performance of engine exhaust pipe. If necessary, sleeve or protective screen can be used to prevent the hose from being heated and deteriorated. When the sand blasting hose must be bent, the bending radius should not be too small, and should be greater than 9 times the outer diameter. There should be a straight line section greater than 2 times the outer diameter of the pipe at the joint between the rubber hose and the joint. How high-quality the products and equipment we use are, it is inevitable that there will be some large and small failures in the process of using them, which will more or less have a certain impact on our work. Just like the use of sandblasting hose, there are traces of its outer adhesive seam, problems must be solved, For this, we explained the following solutions: First, the used water cloth should be used according to the original elastic edge of the water cloth when it is reused. 2： When we wrap the water cloth around the seam of the sandblasting hose, we should apply sufficient and uniform pressure to the pipe body. 3. The water cloth with different widths should be selected according to the size of the outer diameter of the wrapped sandblasting hose (for hose with an outer diameter of less than 30mm, the width of the water cloth should not exceed 90mm). The overlapping width of the water cloth should be 3/5-2/3 of the width of the water cloth.

We are all denominators. Why treat ourselves as molecules. But I think we Extruded tube Price The mass of is absolutely the molecule in the same industry. From raw materials, the general manager is responsible for the purchase of raw materials. Raw materials can only enter the factory after passing the inspection. Because it is the boss's own purchase and inspection, there is no buyer to take kickback, which increases the cost of raw materials and reduces the quality of raw materials. Speaking of the manufacturer's production process, it is difficult to find the second advanced mixer equipment among the new sand pumping hose manufacturers in 2019. It ensures that our glue is more uniform. This ensures the quality of our sand pumping hose. About 70% of sand pumping hose is manual work, and the production technology experience of workshop workers largely determines the quality of our sand pumping hose. 70% of our workshop workers have more than 7 years of production high quality Extruded tube Experience. Select rubber hose Wang Xueyan purchases sand pumping rubber hose, which is more insurance than insurance company. Our goal is to become a member of the hose industry with excellent sand pumping hose quality. Place an order yesterday and deliver it today. At this speed, it is hard to find a second sand pumping hose in the industry. Life doesn't treat us kindly because we are women. But we should treat our own lives well and try to sell sand pumping hoses. As an excellent salesman, will you also receive an inquiry like chicken ribs. When I was just doing business, I received a 3 page quotation, and I patiently sorted it out for about 2 days. Finally, there was no news. Now I have been doing business for more than 10 years. Sometimes I can accurately judge the order rate of this order simply by looking at the inquiry list. The real heart of the words lies in the customers who make good deals.