Henan Rubber steel wire pipe The break of the sandblasting hose usually refers to the appearance and change of the crack of the sandblasting hose. The sandblasting hose has one or more cracks, but the cracks are neat. Another is that the internal bending cracks at the crack of the sandblasting hose are neat. The causes of different errors are different, and the treatment methods are also different. Therefore, in the process of using or protecting the sandblasting hose, the sandblasting hose should not be subject to changing torque. When installing the sandblasting hose, try to keep the axis of the two joints on the same plane to avoid twisting the sandblasting hose in use. Therefore, be careful with the application, and try not to make the sandblasting hose change excessively to avoid consumption. Sand blasting hose plays a very important role in the industry. Its inner rubber layer is added with carbon black, which can effectively eliminate static electricity and directly contact with compressed air and abrasives. The requirement for wear resistance is quite high. Once worn through, the reinforcement layer will be exposed, and the sand blasting hose will burst. The reinforcing layer of sandblasting hose is a pressure resistant layer, so wear-resisting Rubber steel wire pipe The material and layout of the reinforcement layer directly determine the pressure rating of the sandblasting hose. There are two common enhancement layers: cloth clip enhancement layer and surround enhancement layer. The sand blasting hose with an inner diameter of 50mm or more is mostly used in the construction occasions where the sand blasting pipe needs to be extended to reduce the pressure loss in the sand blasting hose and ensure the normal operation of shot blasting.

With the development of modern industry, the demand for high temperature and high pressure sandblasting hoses is growing, Rubber steel wire pipe company Scope of application: completely flexible conveying pipe is required to prevent the pipe from being in vibration position. It is suitable for steam, gas, air, heavy oil, petroleum, chemical industry, etc. First of all, the structure of fire sprinkler metal sandblasting hose (explosion-proof pipe) must have compulsory knowledge. Fire sprinkler metal sandblasting hose (hereinafter referred to as explosion-proof pipe) is a high-quality sandblasting hose in modern industrial pipelines. It is mainly composed of fire sprinkler metal sandblasting hose bellows, fire sprinkler metal sandblasting hose net sleeve and fire sprinkler metal sandblasting hose connector. The inner pipe is a thin-walled stainless steel fire sprinkler metal sandblasting hose corrugated pipe with spiral or circular waveform. The outer layer of the fire sprinkler metal sandblasting hose corrugated pipe is woven by stainless steel wire or steel strip according to certain parameters. The fire spraying metal sand blasting hose connector or flange at both ends of the sand blasting hose shall match with the fire spraying metal sand blasting hose connector or flange of the user's pipeline. wear-resisting Rubber steel wire pipe Scope of application of fire sprinkler metal sandblasting hose (explosion-proof pipe): full flexible conveying pipe is required in vibration places to prevent pipes, which is applicable to steam, gas, air, heavy oil, petroleum, chemical industry, etc. The annular flame spraying metal sandblasting hose bellows is a special geometric pipe. The outer edges of several annular diaphragms are tangent to several concave half rings facing the center, and the inner edges are tangent to several concave half rings of the vest. Its blanks are mainly made of tubes. The fire sprinkler metal sandblasting hose bellows has the characteristics of large flexibility, good elasticity, simple manufacturing and small rigidity.

Due to the limitation of spatial location conditions, wear-resisting Rubber steel wire pipe The installation stress of can often bring various difficulties to the installation work: formed pipes cannot be installed; When you bend down, you are about to come. If you make do with pipes, local cold correction will inevitably occur. According to the size of the pipeline and the specific situation on site, the cold correction amount varies from several millimeters to tens of millimeters, some as high as hundreds of millimeters. Practice has proved that the greater the quantity, the higher the internal stress. These residual installation stresses in the rubber sand blasting pipe are undoubtedly huge hidden information. The lubricating oil duct of a certain type of engine bearing was broken for many times due to excessive installation stress in actual operation. Because it can be bent at will, the internal stress generated by bending under the condition of rated bending radius is very small, which brings great convenience to the installation work, and also plays a certain role in ensuring the safe operation of the rubber sand blasting pipe. This is the main reason why some rubber sand blasting pipes must be used. Since it is necessary to load and unload the mold, the movable cylinder on the vulcanizer will move up and down. After repeated reciprocation, the copper serpentine tube will undergo fatigue fracture. Although it can continue to be used after repair, stopping for repair will cause time loss. Henan Rubber steel wire pipe Although it has good flexibility and strong fatigue resistance, it is also weak in pressure bearing, temperature resistance, aging resistance and other aspects, and can not be used after several months. The good comprehensive performance of rubber sand blasting pipe is fully reflected here.

For the woodworking industry, many users wear-resisting Rubber steel wire pipe Not unfamiliar, this is an industrial dust collector used on woodworking carving machines, mainly used to absorb wood chips, wood ash, etc. At present, there are many kinds of woodworking vacuum tubes on the market. In the past few years, major furniture factories used PVC steel wire hoses with flat ends. In recent years, more and more enterprises have replaced cheap PVC steel wire hoses with more wear-resistant and durable pu steel wire expansion tubes. Some of the former take a few days or a month, while some of the latter take a few months or a year, They are also steel wire hoses. Why is the service life gap so far? First of all, you may have the impression that many PVC hoses have a very bad smell. This kind of hose is often used in daily life. Because the raw material itself is very cheap, the price of the finished product is also very low. For example, only a dozen yuan a piece. Think about the price of PVC raw materials, which is generally 8-15 yuan a kilogram, And most businesses will not use expensive PVC raw materials, Rubber steel wire pipe company The woodworking vacuum tube produced in this way has a very strong smell, not only unpleasant, but also many times the product can not even achieve environmental protection. However, the current updated product, pu steel wire telescopic tube, is a large woodworking furniture factory. An expensive woodworking carving machine uses a cheap vacuum tube with a very smelly smell, which has much to do with the overall style.