Abrasion resistant sand blasting pipe It has a wide range of uses, from the needs of daily life to industrial production and oil exploitation. It can be said that it plays an important role in all walks of life. In the application of different industries, according to their own needs, check the performance of the products, give proper play to the advantages of the products, and ensure the normal use of daily applications.

Replace wear-resistant Sandblasting pipe The length of the rubber hose, the number of steel wire layers, the shape and size of the joint should be reasonable, and the curvature of the rubber hose should be minimized. When tightening the connecting nut, do not tighten the rubber hose. Excessive bending and twisting will greatly reduce the service life of the rubber hose. Protective measures shall be taken for the parts liable to friction to prevent the rubber hose from bursting due to wear.

What should we pay attention to when purchasing wear-resistant sandblasting pipe? Different types of wear-resistant sand blasting pipes have different working pressures. When purchasing rubber hose, first determine the working pressure of the system, and then select the equivalent working pressure of the rubber hose. If the system is often affected by pressure, it is necessary to increase the working pressure of the hose and choose the hose with higher pulse life.

The inner diameter of wear-resistant sand blasting pipe is one of the factors to be considered when selecting rubber hose. The small inner diameter will increase the flow rate of the medium, raise the temperature of the system, reduce the working efficiency, and affect the working performance of the system. The large inner diameter will increase the purchase cost. Therefore, the proper inner diameter should be selected according to the flow rate of the medium. The wear-resistant sand blasting pipe has allowable operating temperature range. The service life and pressure bearing capacity of the rubber pipe can be guaranteed only when it works at an appropriate temperature. When the operating temperature of the equipment exceeds the allowable temperature range of the rubber hose for a long time, special rubber hose shall be purchased or special protective sleeve shall be added on the wear-resistant sand blasting pipe. If the medium to be transported is special, make sure that the hose material is compatible with the medium.

The inner rubber layer of the wear-resistant sand blasting pipe has the function of bearing the pressure of the transmission medium and protecting the steel wire from corrosion, and the outer rubber layer protects the steel wire from damage（ ф 0.3-2.0 reinforcement layer) is the skeleton material for reinforcement

What to pay attention to when storing wear-resistant sand blasting pipe

1. The wear-resistant sand blasting pipe shall be stored in a loose state as far as possible. Generally, rubber hoses with inner diameter less than 76 mm can be wound and stored.

2. During the storage of wear-resistant sand blasting pipe, it is strictly prohibited to stack heavy objects on the pipe body to prevent external extrusion and damage.

3. During the storage of wear-resistant sand blasting pipe, do not contact with acid, alkali, oil, organic solvent or other corrosive liquids and gases, and the heat release should start from 1m away.

4. The storage period of wear-resistant sand blasting pipe shall not exceed 2 years, and it shall be used by one person to prevent the quality of rubber hose from being affected by long-term storage.

five Abrasion resistant sand blasting pipe If temporary outdoor storage is required, the site shall be flat, the rubber hose shall be laid flat, and the upper cover shall be placed under the rubber hose. No heavy objects shall be stacked. At the same time, the hose shall not contact the heat source.

6. The storage place of the upper and lower rubber pipes in the well shall be kept clean and ventilated, and the relative humidity shall be 80. The temperature of the storage place shall be kept between - 15 ℃ and 40 ℃, and the rubber pipe shall be protected from direct sunlight and water spray.

7. When storing wear-resistant sand blasting pipe, both ends of the hose shall be sealed firmly to prevent sundries from entering the hose.

8. When the wear-resistant sand blasting pipe is stored, it should be placed separately according to different varieties and specifications, not mixed, and hang a management board.

9. In order to prevent the pipes from being pressed and deformed during storage, they should not be stacked too high, and the stacking height should not exceed 1.5m. It also requires rubber hoses to be "stacked" frequently during storage, at least once a quarter.