“ wear-resisting Air compression hose What are the applications in engineering transformation? " In this issue, we will explain this problem for you. Those who have consulted this problem will come to see it: First, we should consider the water supply and drainage of all water related equipment, such as wells, pumps, etc., their location, installation method and temperature, including galvanized air ducts. 2、 It is very important to consider galvanized air duct in advance to avoid temporary replacement of galvanized air duct materials. 3、 After the location of the machine tool is determined, the drainage outlet can be considered to be arranged underground, which is not only convenient but also durable. 4、 After river reconstruction, there should be a suppression test, but now many construction teams do not suppress the test. It is usually said that it is not important, that there is water and pressure in the galvanized air duct, and so on. Try to be present to suppress the test. 5. If the installation is completed, pay attention to the inspection of the workshop, water pump room and FRPP drain. If the drainage system is slow, the installation program should be able to open the installation. Water outlets should be protected, especially during civil engineering construction, Air compression hose Price It may cause soil loss and blockage. I believe that you have a better understanding of this information, and we will continue to improve the galvanized air duct to make it more widely used.

wear-resisting Air compression hose Or PVC steel wire spiral reinforced pipe. The commodity is made of high-quality PVC plastic raw materials. PVC steel wire reinforced pipe is also a PVC steel wire reinforced hose that uses steel wire reinforcement. The embedded spiral steel wire is used as the reinforcement layer, so the product has both rigidity and flexibility, that is, it has both satisfying mechanical properties and rigidity, and excellent flexibility. The reinforced pipe of latex fiber is PVC hose embedded with steel wire framework. The inner and outer tube walls are clear, lubricated, free of bubbles, and the fluid transportation is clearly visible. Silicone fiber tube is resistant to low concentration of acid and alkali, high elasticity, not easy to age, and has a long service life. Resistant to high pressure and can be kept intact under high pressure and vacuum. PVC steel wire pipe is made of new PVC reinforced materials, and has made great progress in compressive strength and hardness. The main production method of silica gel steel wire pipe is multiple production method. The main types of steel wire pipe in shopping malls include high pressure steel wire pipe, low pressure steel wire pipe, steel wire skeleton pipe and Tongming steel wire pipe. The application methods are different in different environments. The new PVC steel wire pipe is the most widely used commodity today. Air compression hose Price After use, it will not be the same as the metal pipe, which is easy to deform and leak. What advantages does the PVC fiber reinforced pipe have.

Air duct mainly refers to the ventilation duct of the central air-conditioning system, which is often ignored, but it is an important part of the air-conditioning system. Luoyang Air compression hose What are the regulations for welding air ducts? Gongfa HVAC is a manufacturer dedicated to the production of air ducts, which has been recognized and supported by the majority of users for many years. 1、 The welding regulations of carbon steel plate air duct are as follows: 1. The carbon steel plate air duct should be welded by DC welder. Introduction to welding air duct If AC welding machine is used for welding, a vibrator must be added to reduce excitation and stabilize the arc. When welding steel plates, the arc is unstable, which can lead to deterioration of weld quality. 2. Before welding, remove the dirt, oil stain and rust at the welding port; When spot welding or continuous welding is used, the oxide shall also be removed. The butt joint shall be kept with the minimum gap, and the overlap at the manual spot welding location shall be removed in time. After welding, the electrode slag and residual welding wire in the weld and its surrounding area shall be removed in time. 2、 The welding regulations of stainless steel air duct are as follows: 1. Before welding the air duct, remove the grease and dirt in the weld area to prevent pores and sand holes in the weld. Cleaning can be carried out with gasoline, acetone, etc. When welding stainless steel plates by electric arc welding, the surfaces on both sides of the weld should be coated with white ash, Luoyang Air compression hose To avoid welding slag splashes adhering to the surface of the plate. 2. After welding, attention shall be paid to removing the slag at the weld, brushing the metal luster with a copper wire brush, pickling with 10% nitric acid solution, and then cleaning with hot water.

You know? Luoyang Air compression hose Are there reinforcement regulations and requirements? Stainless steel welded air duct is a commonly used equipment, and its reinforcement actually has regulations and requirements, do you know? If in pipe support is adopted, the spacing between each support point and the edge or flange of the air duct shall be uniform, and the value shall not be greater than 950 mm. If the corrugated bars or wires are used for reinforcement, the arrangement should be regular and the spacing should be even. Moreover, there should be no obvious deformation and other problems for the board surface. If the welded air duct is reinforced, it should be made of ribbed bars, vertical bars, angle steel, flat steel, reinforcing bars and supports inside the duct. The appropriate one can be selected according to the actual situation and needs. If angle steel or reinforcing bars are used, they should also be arranged neatly and symmetrically. The height shall not be greater than the flange width. Principles and requirements for stainless steel air duct plate connection. When the thickness is less than or equal to 1mm, the splicing of plates shall be done by biting or riveting. When the thickness of plates is greater than 1mm, argon arc welding or electric arc welding shall be used instead of gas welding. The mature argon arc welding process of "single side welding, double side forming" shall be adopted; When assembling weldments, the welding materials and process measures selected for spot welding shall be consistent with the formal Air compression hose Price The requirements are the same. The misalignment deviation of the pipe butt joint is less than 20% of the wall thickness and less than 2mm. Adjust the butt joint clearance, and do not use the method of heating, tensioning and twisting the pipe. It is not allowed to strike an arc or test the current on the weldment, and the pipe surface shall be free of arc scratch and other defects. Splash prevention measures shall be taken during welding. After welding, the slag and spatter shall be cleaned with stainless steel flat shovel. After welding, the slag on the weld surface and the spatter on both sides shall be cleaned.

The reason why welded air duct has become the favorite of the market, Luoyang Air compression hose Compared with the air duct made of traditional materials, it has obvious advantages in technology, energy conservation, environmental protection and economy. This product has been inspected, tested and proved by the National Building Materials Testing Center, the National Fire Building Materials Quality Supervision and Inspection Center, the National Air Conditioning Equipment Quality Supervision and Inspection Center, the National Non ferrous Metal Quality Supervision and Inspection Center and other relevant authorities, In addition, no smoke is generated in the fire, and the smoke density is only 4, which is 10 to 20 times that of other organic foam materials. In modern buildings, central air conditioning is very common, and ventilation ducts are an important part of the central air conditioning system. According to statistics, China's annual demand is about 100 million square meters, reaching 20 billion yuan. Among all kinds of air ducts, welded air ducts stand out for their unique excellent performance and cost performance, and are becoming the new favorite in the central air-conditioning market. The manufacturing of welded air ducts is highly automated and the production speed is very fast. Ordinary air ducts can produce 20~40 meters per minute. Due to the low price of the raw material galvanized strip steel compared with the whole galvanized steel sheet, and its factory production and specification standardization, the cost is lower than that of rectangular air ducts; In addition, the total cost is low due to the less demand for supports and hangers and the less installation work. Since the four corners of rectangular air duct are prone to turbulence, Air compression hose Price The effective flow area is reduced. The technology of welded air duct is very close to the international level; In terms of supporting services, more and more enterprises like this company provide high standard services. If there are any suggestions, we hope to see more and more enterprises with a sense of mission for the development of the industry.

Luoyang Air compression hose 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Air compression hose Price When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.