The hard core method adopts the core extrusion process to extrude the inner rubber tube blank, which directly uses the extruder to cover the inner rubber tube blank on the iron core, instead of the traditional casing process, and simplifies the process flow. Lhasa Corbel tube The billet forming adopts the process method of intertwining outer film and steel wire braiding forming. Similar to wrapping water wrapped cloth, the overlapping width is 1/2 of the film width. This process method can replace the method of wrapping outer film by extruder or by hand, reducing energy consumption and cost. We all know that the reinforcing layer and reinforcing layer of the rubber hose are the main force bearing parts, which are used to bear the load pressure. The factors determining the stress condition of the reinforced layer of the rubber hose are determined by the tension of the braided steel wire and the braiding angle. The high-speed steel wire hose braiding machine developed by our factory has introduced the advanced technology of foreign braiding production lines, and integrated the characteristics of domestic braiding machines. It integrates the advanced functions of hydraulic brake hose braiding production line, such as horizontal mechanical transmission, automatic lubrication, and so on, to develop equipment with high productivity and high degree of automation. The range of braiding diameter can be achieved Ф 6— Ф 25 Long core rubber hose (reinforcement layer). It fills the gap of domestic knitting production equipment, which can be widely used in rubber and plastic hose, rubber hose (reinforcement layer) knitting production equipment. The structure of high-pressure rubber hose is composed of four parts: inner liner, inner rubber layer, skeleton layer, middle rubber layer and outer rubber layer. Corbel tube company In case of direct contact with the conveying medium, the synthetic rubber with good medium resistance, high tensile strength, high constant tensile stress, small compression permanent deformation and easy processing is usually selected. In order to meet the use requirements of strong polar medium resistance, the inner liner is composed of polytetrafluoroethylene layer and rubber layer, and a layer of film or adhesive is added on the surface of the inner liner to improve the adhesion with the skeleton material.
With the rapid development of the national economy and the continuous improvement of the technical level, almost all walks of life need to do exhaust ventilation systems, Lhasa Corbel tube What are the advantages worth pursuing? 1. The welding method is unique. It adopts a new low temperature welding form, which does not damage the galvanized layer of the product. The welding spot is firm, the weld seam is beautiful, and the sealing is good. After welding, no treatment is required for the weld seam. 2. The manufacture of mechanically formed air duct makes the high-quality galvanized sheet not damaged, and the galvanized layer not damaged, thus prolonging the service life. 3. The specification is uniform and the size is standard, which ensures that the inner wall of the pipeline is flat and smooth, so that it is easy to clean and the material transportation is smooth. 4. The self forming flange can make the pipe material uniform, no longer use angle steel flange, and reduce the pipe weight by more than 20%, so the load bearing capacity of the building can be greatly reduced, thus reducing the overall cost of the building. 5. Enhance the beautiful pipeline, beautiful appearance, exquisite structure, smooth lines, superior performance, and the installation of exposed air ducts, especially suitable for this product. 6. Typical round air pipe fittings are generally 3-6 meters long and rectangular pipe fittings are 1-1.5 meters long, reducing the connection points of pipe fittings and minimizing the leakage at the joint of pipe fittings. 7. The pipe fittings, joints and spare parts made by mechanized assembly line all have standard sealing rings. As they are produced in a standardized and factory way, they have better air tightness. 8. Mechanically formed compression ribs and stiffeners can improve the strength of the pipe wall, save material thickness and reduce costs. The thickness of the seam of the spiral pipe is 4 times that of the pipe body, which makes the pipe very rigid and has the best pressure bearing performance, especially the negative pressure. 9. Scientific joint and seaming methods can ensure smooth pipeline gas without affecting pipeline flow diameter. Therefore, mechanized assembly line production improves production efficiency and effectively shortens delivery cycle. Advanced computer process control program blanking, production, Corbel tube company It ensures the dimensional accuracy of pipeline components, thus ensuring fast and convenient installation and construction, and improving work efficiency and economic benefits.
Lhasa Corbel tube 1. The manufacturing quality shall be guaranteed according to the national standards of Oxygen Hose (GB/T2550-91) and Acetylene Hose (GB/T2551-91) respectively, and the hose shall have sufficient compressive strength and flame retardant characteristics. According to the national standard, the oxygen hose is red, the working pressure vessel is 1.5MPa, the inner diameter of the hose is 8mm, and the outer diameter is 18mm; 2. Care must be taken when storing and using the hose to keep it clean and free from damage. For example, avoid exposure to sunlight, rain and snow, and prevent contact with substances such as acid, alkali, oil and other organic solvents that can damage the hose. The storage temperature shall be - 15 ℃~40 ℃, and the distance from the personnel shall not be less than 1m; 3. When using a new hose, the talcum powder on the inner wall of the hose must be blown out first to prevent the channel of the welding torch from being blocked. Avoid external extrusion and mechanical damage during use, and do not fold the pipe body. 4. If the oxygen hose catches fire, stop the air supply first, and then deal with the fire hose, but do not bend the hose. The cylinder valve must be closed when the cylinder is not in use or after work. 5. The hose with bulge, crack or air leakage shall not be used, and the air leakage hose shall not be used after being stuck with adhesive tape. Corbel tube company When connecting the two ends of the hose with tools, clamp or wire shall be used to fasten, and the intermediate joint shall be fastened with a gas pipe connector.
The consumption of galvanized iron sheet air duct in China's chemical industry also shows a rapid growth trend. The rapid increase in the consumption of galvanized iron sheet air duct in China's chemical industry has stimulated domestic Corbel tube company With the rapid development of industry and the support of relevant government policies, in a short period of time, the production of galvanized iron air ducts in China has been developing rapidly. From the perspective of industrial chain, galvanized iron duct and upstream and downstream products enterprises of galvanized iron duct are interdependent and competing industries. Steel production enterprises can establish long-term and stable strategic alliances with downstream enterprises through deep processing of steel products, which is conducive to promoting the development of new varieties, quality improvement and market expansion of galvanized iron sheet air duct industry, and is an effective way to extend the value of steel products to the downstream and improve the competitiveness of the product market. It can be said that the development of high-quality galvanized iron duct projects has become a development strategy for Chinese galvanized iron duct manufacturers to cope with fierce market competition and improve product competitiveness. At present, in the consumption structure of galvanized iron duct in China, except for some high-end products that still rely on imports, middle and low-end products can basically achieve self-sufficiency. The situation that galvanized iron duct consumption completely depends on imports has been greatly improved, and the export volume is also expanding rapidly. However, compared with the developed areas of galvanized iron duct industry, China's galvanized iron duct industry system is not perfect, and there is still a big gap compared with Japan, South Korea and other large stainless steel reactor production countries. The development of galvanized iron sheet air duct industry in China started late, and the social demand for stainless steel reaction kettle grew too fast, which led to production Corbel tube The first problem to be solved for industrial development is to rapidly increase output to meet the growing social demand, gradually replace imports, and complete the two steps of "quantitative change" and "qualitative change". At present, the development of galvanized iron duct industry in China has completed the accumulation process of "quantitative change", and is currently facing the transformation of "quality".
production Corbel tube 1. During the molding of rubber products, the cohesive force of the elastomer cannot be eliminated due to the large pressure pressing. During the molding and mold release, extremely unstable shrinkage (the shrinkage rate of rubber varies due to different rubber types) often occurs. It must take a period of time before it can be gentle and stable. Therefore, at the beginning of the design of a rubber product, no matter the formula or the mold, it is necessary to carefully calculate the matching. If not, it is easy to cause dimensional instability of the product, resulting in low product quality. 2. Rubber belongs to thermosetting elastomer, while plastic belongs to thermosetting elastomer. Due to different sulfide types, the temperature range of rubber molding and curing is quite different, even affected by climate change and indoor temperature and humidity. Therefore, the production conditions of rubber products need to be properly adjusted at any time. If not, there may be differences in product quality. 3. The rubber product is the rubber mixture made from rubber raw materials after mixing in the internal mixer as the raw material. The formula is designed according to the characteristics of the required rubber products during mixing, and the required product hardness is determined. The product is molded by the rubber plate vulcanizer. After the product is formed, flash processing shall be carried out to make the product surface smooth without burrs. 4. The aging test of rubber products belongs to the category of aging test. Rubber aging refers to the phenomenon that the performance and structure of rubber and products are changed due to the combined effect of internal and external factors in the process of processing, storage and use, thus losing their use value. Corbel tube company It is characterized by cracking, tackiness, hardening, softening, chalking, discoloration, mildew, etc. The following conditions shall be met when the ball mill uses the rubber lining plate: 1. The hardness of the ground material. The iron base alloy is similar to the rubber lining plate for materials below medium hardness, and the rubber lining plate is superior for materials above medium hardness. 2. The temperature of rubber lining plate is generally 70 ℃ - 90 ℃, and it can reach 110-130 ℃ under special circumstances. The temperature should be lower during dry grinding. 3. Feed size. Generally, the ball mill shall be more than 20-25mm; For the autogenous mill, the feeding particle size can be larger because no steel ball is added.
